Enhancement of Mechanical Properties of PCL/PLA/DMSO2 Composites for Bone Tissue Engineering
Source abstract
Abstract
Bone tissue engineering shows potential for regenerating or replacing damaged bone tissues by utilizing biomaterials renowned for their biocompatibility and structural support capabilities. Among these biomaterials, polycaprolactone (PCL) and polylactic acid (PLA) have gained attention due to their biodegradability and versatile applications. However, challenges such as low degradation rates and poor mechanical properties limit their effectiveness. Dimethyl sulfone (DMSO2) has emerged as a potential additive to address these limitations, offering benefits such as reduced viscosity, increased degradation time, and enhanced surface tension. In this study, we investigate tailored composites comprising PLA, PCL, and DMSO2 to enhance mechanical properties and hydrophilicity. Through material characterization and mechanical testing, we found that the addition of DMSO2 led to improvements in the yield strength, modulus, and hydrophilicity of the composites. PCL and DMSO2 10, 20, and 30 wt% were premixed, and 20 wt% PCL + 10, 20, and 30 wt% DMSO2 were mixed with PLA. Specifically, PLA/PCL/DMSO2 composites exhibited higher yield strengths and moduli compared to pure PLA, pure PCL, and PLA/PCL composites. Moreover, the hydrophilicity of the composites increased with DMSO2 concentration, facilitating cell attachment. Fourier-transform infrared spectroscopy (FTIR) confirmed the presence of –COOH and –COH bands in PLA/PCL/DMSO2 composites, indicating chemical interactions between DMSO2 and the polymer matrix. Fractography analysis revealed enhanced interface adhesion in PLA/PCL/DMSO2 composites due to the hydrogen bonding. Overall, this study demonstrates the potential of PLA/PCL/DMSO2 composites in bone tissue engineering applications, offering improved mechanical properties and enhanced cell compatibility. The findings contribute to the advancement of biomaterials for additive manufacturing in tissue engineering and regenerative medicine.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: biodegradable polymer synthesis and properties · Bone Tissue Engineering Materials · Electrospun Nanofibers in Biomedical Applications
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Department of Mechanical and Material Engineering, Portland State University, Portland, OR 97201, USA
Funding
Korea Institute of Industrial Technology
References (76)
Show source-provided references
1. Bone tissue engineering10.1007/s40610-015-0022-2 ↗
2. Bioprinting of three-dimensional scaffold based on alginate-gelatin as soft and hard tissue regeneration10.1016/j.jmrt.2021.08.069 ↗
3. Scaffold characteristics, fabrication methods, and biomaterials for the bone tissue engineering10.1007/s12541-022-00755-7 ↗
4. Bone tissue engineering: State of the art and future trends10.1002/mabi.200400026 ↗
5. Bone tissue engineering: Recent advances and challenges10.1615/CritRevBiomedEng.v40.i5.10 ↗
6. Development and biocompatibility evaluation of biodegradable bacterial cellulose as a novel peripheral nerve scaffold10.1002/jbm.a.36330 ↗
7. Characterization and biocompatibility of a fibrous glassy scaffold10.1002/term.2017 ↗
8. Use of Dimethyl Sulfone as Additive in Aprotic Electrolytes10.1149/04801.0135ecst ↗
9. Biodegradable polymers as biomaterials10.1016/j.progpolymsci.2007.05.017 ↗
10. Physical approaches to biomaterial design10.1038/nmat2344 ↗
11. Biomaterials and biocompatibility: An historical overview10.1002/jbm.a.36930 ↗
12. Dielectric and biodegradation properties of biodegradable nano-hydroxyapatite/starch bone scaffold10.1016/j.jmrt.2022.04.014 ↗
13. Biodegradable and biocompatible polymers for tissue engineering application: A review10.3109/21691401.2016.1146731 ↗
14. Biomaterials and fabrication to optimise scaffold properties for musculoskeletal tissue engineering10.2174/1574888X11666160614101037 ↗
15. Sulfur in human health
16. Fracture micromechanisms of bioabsorbable PLLA/PCL polymer blends10.1016/j.engfracmech.2006.05.021 ↗
17. Toughening of polylactic acid: An overview of research progress10.1080/03602559.2015.1098698 ↗
18. Mechanical and biological behaviour of PCL and PCL/PLA scaffolds for tissue engineering applications
19. Fracture mechanisms of biodegradable PLA and PLA/PCL blends
20. Large-scale production, properties and commercial applications of polylactic acid polymers10.1016/S0141-3910(97)00148-1 ↗
21. A literature review of poly (lactic acid)10.1023/A:1020200822435 ↗
22. An overview of polylactides as packaging materials10.1002/mabi.200400043 ↗
23. Averous, L., and Pollet, E. (2012). Environmental Silicate Nano-Biocomposites, Springer.10.1007/978-1-4471-4108-2 ↗
24. The design of scaffolds for use in tissue engineering. Part II. Rapid prototyping techniques10.1089/107632702753503009 ↗
25. 3D printing of personalized artificial bone scaffolds10.1089/3dp.2015.0001 ↗
26. Poly-ε-caprolactone and its copolymers
27. Polymer blends
28. Crystallization, morphology, and mechanical behavior of polylactide/poly (ε-caprolactone) blends10.1002/pen.20609 ↗
29. Preparation and characterization of biodegradable PLA/PCL polymeric blends10.1016/j.mspro.2014.07.201 ↗
30. Influence of blending and blend morphology on the thermal properties and crystallization behaviour of PLA and PCL in PLA/PCL blends10.1007/s10853-016-9784-z ↗
31. Micromechanical analysis and fracture mechanics of Poly (lactic acid)(PLA)/Polycaprolactone (PCL) binary blends10.1016/j.polymertesting.2023.107984 ↗
32. Hou, A.-L., and Qu, J.-P. (2019). Super-toughened poly (lactic acid) with poly (ε-caprolactone) and ethylene-methyl acrylate-glycidyl methacrylate by reactive melt blending. Polymers, 11.10.3390/polym11050771 ↗
33. Wong, T., Bloomer, R.J., Benjamin, R.L., and Buddington, R.K. (2017). Small intestinal absorption of methylsulfonylmethane (MSM) and accumulation of the sulfur moiety in selected tissues of mice. Nutrients, 10.10.3390/nu10010019 ↗
34. Physicochemical properties of aqueous solutions of dimethyl-and diethylsulfones10.1134/S0036024411120211 ↗
35. Osteoarthritis: A disease of the joint as an organ10.1002/art.34453 ↗
36. Jang, J.-W., Min, K.-E., Kim, C., Wern, C., and Yi, S. (2023). PCL and DMSO2 composites for bio-scaffold materials. Materials, 16.10.3390/ma16062481 ↗
37. (1997). Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials (Standard No. ASTM D790).
38. (2013). Standard Practice for Surface Wettability of Coatings, Substrates and Pigments by Advancing Contact Angle Measurement (Standard No. D7334-08).
39. The impact of contact angle on the biocompatibility of biomaterials10.1097/OPX.0b013e3181da863e ↗
40. Surface modification of poly (lactic acid) by UV/Ozone irradiation10.1007/s12221-008-0106-1 ↗
41. Electrospun PCL and PLA hybrid nanofibrous scaffolds containing Nigella sativa herbal extract for effective wound healing10.1002/app.49528 ↗
42. Influence of chemistry and fiber diameter of electrospun PLA, PCL and their blend membranes, intended as cell supports, on their biological behavior10.1016/j.polymertesting.2021.107364 ↗
43. Liu, Q., Jia, H., Ouyang, W., Mu, Y., and Wu, Z. (2021). Fabrication of antimicrobial multilayered nanofibrous scaffolds-loaded drug via electrospinning for biomedical application. Front. Bioeng. Biotechnol., 9.10.3389/fbioe.2021.755777 ↗
44. Melt electrowriting of PLA, PCL, and composite PLA/PCL scaffolds for tissue engineering application10.1038/s41598-022-24275-6 ↗
45. Development of biodegradable webs of PLA/PCL blends prepared via electrospinning: Morphological, chemical, and thermal characterization10.1002/jbm.b.34846 ↗
46. Preparation and characterisation of polylactic acid (PLA)/polycaprolactone (PCL) composite microfibre membranes10.5604/12303666.1196607 ↗
47. Agrawal, G., Negi, Y.S., Pradhan, S., Dash, M., and Samal, S. (2017). Wettability and contact angle of polymeric biomaterials. Characterization of Polymeric Biomaterials, Elsevier.10.1016/B978-0-08-100737-2.00003-0 ↗
48. Investigation of cell–surface interactions using chemical gradients formed from plasma polymers10.1016/j.biomaterials.2007.09.026 ↗
49. Factors that determine the protein resistance of oligoether self-assembled monolayers−internal hydrophilicity, terminal hydrophilicity, and lateral packing density10.1021/ja034820y ↗
50. Self-assembled monolayers that resist the adsorption of proteins and the adhesion of bacterial and mammalian cells10.1021/la010552a ↗
51. Chemically diverse polymer microarrays and high throughput surface characterisation: A method for discovery of materials for stem cell culture10.1039/C4BM00054D ↗
52. Haddad, T., Noel, S., Liberelle, B., El Ayoubi, R., Ajji, A., and De Crescenzo, G. (2016). Fabrication and surface modification of poly lactic acid (PLA) scaffolds with epidermal growth factor for neural tissue engineering. Biomatter, 6.10.1080/21592535.2016.1231276 ↗
53. Simple surface modification of poly (ε-caprolactone) to induce its apatite-forming ability
54. Fortelny, I., Ujcic, A., Fambri, L., and Slouf, M. (2019). Phase structure, compatibility, and toughness of PLA/PCL blends: A review. Front. Mater., 6.10.3389/fmats.2019.00206 ↗
55. Preparation and Characterization of Polycaprolactone (PCL) Antimicrobial Wound Dressing Loaded with Pomegranate Peel Extract10.1021/acsomega.2c08180 ↗
56. Polylactic acid (PLA)/banana fiber (BF) biodegradable green composites10.1007/s10965-011-9646-y ↗
57. Enhanced bone tissue regeneration using a 3D-printed poly (lactic acid)/Ti6Al4V composite scaffold with plasma treatment modification10.1038/s41598-023-30300-z ↗
58. Eshraghi, S., and Das, S. (2010). Mechanical and microstructural properties of polycaprolactone scaffolds with 1-D, 2-D, and 3-D orthogonally oriented porous architectures produced by selective laser sintering. Acta Biomater., 6.10.1016/j.actbio.2010.02.002 ↗
59. McKeen, L.W. (2021). The Effect of Long Term Thermal Exposure on Plastics and Elastomers, William Andrew.
60. Solechan, S., Suprihanto, A., Widyanto, S.A., Triyono, J., Fitriyana, D.F., Siregar, J.P., and Cionita, T. (2023). Characterization of PLA/PCL/Nano-Hydroxyapatite (nHA) biocomposites prepared via cold isostatic pressing. Polymers, 15.10.3390/polym15030559 ↗
61. Physical and mechanical properties of PLA, and their functions in widespread applications—A comprehensive review10.1016/j.addr.2016.06.012 ↗
62. Synergistic effects in mechanical properties of PLA/PCL blends with optimized composition, processing, and morphology10.1039/C5RA21178F ↗
63. Role of binder on yield strength of polycaprolactone/dimethylsulfone composites for bio-applications10.1016/j.jmrt.2023.09.238 ↗
64. Copolymerization Involving Sulfur-Containing Monomers10.1021/acs.chemrev.3c00437 ↗
65. Increasing surface hydrophilicity in poly (lactic acid) electrospun fibers by addition of PLA-b-PEG co-polymers
66. Proliferation and osteogenic differentiation of mesenchymal stem cells on three-dimensional scaffolds made by thermal sintering method10.1007/s11696-021-01774-w ↗
67. Åkerlund, E., Diez-Escudero, A., Grzeszczak, A., and Persson, C. (2022). The effect of PCL addition on 3D-printable PLA/HA composite filaments for the treatment of bone defects. Polymers, 14.10.3390/polym14163305 ↗
68. Solechan, S., Suprihanto, A., Widyanto, S.A., Triyono, J., Fitriyana, D.F., Siregar, J.P., and Cionita, T. (2022). Investigating the Effect of PCL Concentrations on the Characterization of PLA Polymeric Blends for Biomaterial Applications. Materials, 15.10.3390/ma15207396 ↗
69. Preparation and characterization of microspheres based on blend of poly (lactic acid) and poly (ε-caprolactone) with poly (vinyl alcohol) as emulsifier10.1016/j.arabjc.2010.08.003 ↗
70. Impact toughness and ductility enhancement of biodegradable poly (lactic acid)/poly (ε-caprolactone) blends via addition of glycidyl methacrylate10.1155/2013/976373 ↗
71. Hesse, M., Meier, H., and Zeeh, B. (2005). Spektroskopische Methoden in der Organischen Chemie, Georg Thieme.10.1055/b-002-46985 ↗
72. Direct Oxidation of Dimethylsulphoxide and Reduction of Maleic Acid in Methanesulphonic Acid Medium
73. Highly ordered supramolecular structure built from poly (4-(4-vinylphenylpyridine)) and 1, 1′-ferrocenedicarboxylic acid via hydrogen bonding10.1039/D0PY00066C ↗
74. From polyacrylonitrile, its solutions, and filaments to carbon fibers: I. Phase state and rheology of basic polymers and their solutions10.1002/adv.21758 ↗
75. Absorption, desorption and spectroscopic investigation of sulfur dioxide in the binary system ethylene glycol+ dimethyl sulfoxide10.1016/j.fluid.2015.06.047 ↗
76. Baek, J.-H. (2007). Change of Properties of Epoxy Resin Blended with the Modified Epoxy, Pukyong National University.