Low-Grade Clay as an Alkali-Activated Material
Source abstract
Abstract
The potential application of alkali-activated material (AAM) as an alternative binder in concrete to reduce the environmental impact of cement production has now been established. However, as the production and availability of the primarily utilized waste materials, such as fly Ash and blast furnace slag, decrease, it is necessary to identify alternative materials. One such material is clay, which contains aluminosilicates and is abundantly available across the world. However, the reactivity of untreated low-grade clay can be low. Calcination can be used to activate clay, but this can consume significant energy. To address this issue, this paper reports the investigation of two calcination methodologies, utilizing low-temperature and high-temperature regimes of different durations, namely 24 h heating at 120 °C and 5 h at 750 °C and, and the results are compared with those of the mechanical performance of the AAM produced with untreated low-grade clay. The investigation used two alkali dosages, 10% and 15%, with an alkali modulus varying from 1.0 to 1.75. An increase in strength was observed with calcination of the clay at both 120 and 750 °C compared to untreated clay. Specimens with a dosage of 10% showed enhanced performance compared to those with 15%, with Alkali Modulus (AM) of 1.0 giving the optimal strength at 28 days for both dosages. The strengths achieved were in the range 10 to 20 MPa, suitable for use as concrete masonry brick. The conversion of Al (IV) is identified as the primary factor for the observed increase in strength.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Concrete and Cement Materials Research · Recycling and utilization of industrial and municipal waste in materials production · Magnesium Oxide Properties and Applications
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Civil and Infrastructure Engineering, School of Engineering, RMIT University, Melbourne, Victoria 3000, Australia
References (70)
Show source-provided references
1. On the Development of Fly Ash-BasedGeopolymer Concrete
2. The suitability of thermally activated illite/smectite clay as raw material for geopolymer binders10.1016/j.clay.2009.08.026 ↗
3. Impacts, A. (2014). Vulnerability, Part A: Global and Sectoral Aspects. Contribution of Working Group II to the Fifth Assessment Report of the Intergovenmental Panel on Climate Change, Cambridge University Press. Climate Change 2014.
4. Minimising the global warming potential of clay based geopolymers10.1016/j.jclepro.2014.04.046 ↗
5. IEA (2019). Global Status Report for Buildings and Construction, IEA.
6. Alkali-activated binders: A review. Part 2. About materials and binders manufacture10.1016/j.conbuildmat.2007.03.019 ↗
7. Engineering and durability properties of concretes based on alkali-activated granulated blast furnace slag/metakaolin blends10.1016/j.conbuildmat.2012.01.017 ↗
8. Strength and Durability Performance of Fly Ash-Based Process-Modified Geopolymer Concrete10.1061/(ASCE)MT.1943-5533.0002793 ↗
9. Mineralogical and microstructural characterisation of alkali-activated fly ash/slag pastes10.1016/S0958-9465(02)00059-8 ↗
10. Long term durability properties of class F fly ash geopolymer concrete10.1617/s11527-014-0268-9 ↗
11. Natural fibers as reinforcement additives for geopolymers A review of potential eco-friendly applications to the construction industry
12. Du, W., Wang, X., Chen, G., Zhang, J., and Slany, M. (2020). Synthesis, Property and Mechanism Analysis of a Novel Polyhydroxy Organic Amine Shale Hydration Inhibitor. Minerals, 10.10.3390/min10020128 ↗
13. Alkali activation behaviour of un-calcined montmorillonite and illite clay minerals10.1016/j.clay.2018.09.011 ↗
14. Karozou, A., Konopisi, S., Pavlidou, E., and Stefanidou, M. (2020). Long-Term Behavior and Durability of Alkali-Activated Clay Mortars. Materials, 13.10.3390/ma13173790 ↗
15. Masson-Delmotte, V., Zhai, P., Pörtner, H.-O., Roberts, D., Skea, J., Shukla, P.R., Pirani, W.M.-O.A., Péan, C., Pidcock, R., and Connors, S. (2019). 2018: Global Warming of 1.5 °C. An IPCC Special Report on the Impacts of Global Warming of 1.5 °C Above Pre-industrial Levels and Related Global Greenhouse Gas Emission Pathways, in the Context of Strengthening the Global Response to the Threat of Climate Change, Sustainable Development, and Efforts to Eradicate Poverty, IPCC.
16. The identification of geopolymer affinity in specific cases of clay materials10.1016/j.clay.2014.09.042 ↗
17. Thermally treated clay sediments as geopolymer source material10.1016/j.clay.2015.01.027 ↗
18. Comparing the performances of bricks made with natural clay and clay activated by calcination and addition of sodium silicate10.1016/j.clay.2011.08.005 ↗
19. Optimization of geopolymer synthesis by calcination and polycondensation of a kaolinitic residue10.1016/S0921-3449(03)00023-5 ↗
20. Effect of thermal pre-treatment conditions of common clays on the performance of clay-based geopolymeric binders10.1016/j.clay.2012.09.010 ↗
21. Effects of metakaolin addition on geopolymer prepared from natural kaolinitic clay10.1016/j.clay.2017.06.019 ↗
22. Optimization of geopolymers based on natural zeolite clinoptilolite by calcination and use of aluminate activators10.1016/j.conbuildmat.2020.118257 ↗
23. Correlation between pore structure, compressive strength and thermal conductivity of porous metakaolin geopolymer10.1016/j.conbuildmat.2020.118641 ↗
24. Synthesis and characterization of self-healing geopolymer composite10.1016/j.conbuildmat.2020.118432 ↗
25. Low viscosity metakaolinite based geopolymer binders10.1016/j.conbuildmat.2019.116978 ↗
26. Advances in alkali-activation of clay minerals10.1016/j.cemconres.2020.106050 ↗
27. Mechanical activation of fly ash: Effect on reaction, structure and properties of resulting geopolymer10.1016/j.ceramint.2010.09.038 ↗
28. Tahmasebi Yamchelou, M., Law, D.W., Li, J., and Patnaikuni, I. (2020). Alkali activation of mechanically activated low grade clay. J. Sustain. Cem. Based Mater.10.1080/21650373.2020.1838355 ↗
29. Microstructural characterisation of geopolymers synthesised from kaolinite/stilbite mixtures using XRD, MAS-NMR, SEM/EDX, TEM/EDX, and HREM10.1016/S0008-8846(02)00859-1 ↗
30. Ramezanianpour, A.A. (2014). Metakaolin. Cement Replacement Materials, Springer.10.1007/978-3-642-36721-2 ↗
31. Preparation and performance of geopolymers10.1007/s11595-007-3326-0 ↗
32. Guo, X., Shi, H., Chen, L., and Dick, W.A. (2009–7, January 4). Performance and mechanism of alkali-activated complex binders of high-Ca fly ash and other Ca-bearing materials. Proceedings of the 3rd World of Coal Ash, WOCA Conference, Lexington, KY, USA.
33. Comparative performance of geopolymers made with metakaolin and fly ash after exposure to elevated temperatures10.1016/j.cemconres.2007.08.021 ↗
34. Development of Low Cost Geopolymer from Calcined Sedimentary Clay10.1007/978-94-017-9939-3_44 ↗
35. Geopolymerization of halloysite via alkali-activation: Dependence of microstructures on precalcination10.1016/j.clay.2019.105375 ↗
36. Geopolymer synthesis using low-grade clays
37. Quantitative Rietveld analysis of the amorphous content in cements and clinkers10.1023/A:1026363906432 ↗
38. X-ray powder diffraction-based method for the determination of the glass content and mineralogy of coal (co)-combustion fly ashes10.1016/j.fuel.2009.11.024 ↗
39. Standards Australia (2000). AS411.5-2000 Methods for sampling and testing aggregates, Method 5: Particle density and water absorption of fine aggregate. AS 1141.5-200 (Australian Standards), Standards Australia.
40. Adam, A.A. (2009). Strength and Durability Properties of Alkali Activated Slag and Fly Ash based geopolymer Concrete. [Ph.D. Thesis, RMIT University].
41. International ASTM (2002). C109/C109M-16a. Standard Test Method for Compressive Strength of Hydraulic Cement Mortars 2016, ASTM International.
42. Factors influencing the compressive strength of fly ash based geopolymers10.1016/j.conbuildmat.2015.11.045 ↗
43. Long term permeation properties of different fly ash geopolymer concretes10.1016/j.conbuildmat.2016.07.121 ↗
44. Rahman, M.M., Law, D.W., and Patnaikuni, I. (2017, January 22–25). Factors affecting the performance of 100% clay based geopolymer concrete. Proceedings of the 28th Biennial National Conference of the Concrete Institute of Australia, Adelaide, Australia.
45. Effects of curing temeperature and NaOH addition on hydration and strength development of clinker free CKD-fly ash binders10.1016/j.cemconres.2003.08.003 ↗
46. Compressive strength and microstructure evolution of low calcium brown coal fly ash-based geopolymer
47. Properties of geopolymer with seeded fly ash and rice husk bark ash10.1016/j.msea.2011.06.027 ↗
48. Factors influencing strength development in clay-fly ash geopolymer10.1016/j.conbuildmat.2013.05.104 ↗
49. Microcracking and strength development of alkali activated slag concrete10.1016/S0958-9465(01)00003-8 ↗
50. Effect of curing temperature on the development of hard structure of metakaolin-based geopolymer10.1016/j.conbuildmat.2009.12.023 ↗
51. Compatibility studies between N-A-S-H and C-A-S-H gels. Study in the ternary diagram Na2O-CaO-Al2O3-SiO2-H2O10.1016/j.cemconres.2011.05.006 ↗
52. The origin of the pozzolanic activity of calcined clay minerals: A comparison between kaolinite, illite and montmorillonite10.1016/j.cemconres.2010.09.013 ↗
53. Thermal treatment and pozzolanic activity of Na- and Ca-montmorillonite10.1016/0169-1317(95)00037-2 ↗
54. The corrosion of kaolinite by iron minerals and the effects on geopolymerization10.1016/j.clay.2016.12.040 ↗
55. Comparison of calcined illitic clays (brick clays) and low-grade kaolinitic clays as supplementary cementitious materials10.1617/s11527-019-1393-2 ↗
56. Geopolymers from Algerian metakaolin. Influence of secondary minerals10.1016/j.clay.2008.11.001 ↗
57. Abdullah, M.M.A.B., Mimg, L.Y., Yong, H.C., and Tahir, M.F.M. (2018). Clay-Based Materials in Geopolymer Technology. Cement Based Materials, Intechopen.10.5772/intechopen.74438 ↗
58. Do geopolymers actually contain nanocrystalline zeolites? A reexamination of existing results10.1021/cm050230i ↗
59. Ulcina, K., Strepankova, H., Rimal, V., Hanzlitec, T., and Perna, I. (2013). NMR Study of aluminium Coordination in Clays. WDS’13 22nd Annual Conference of Doctoral Students, MATFYZPRESS.
60. Reactions, Phases and Microstructure of Fly Ash based Alkali-Activated Materials10.3151/jact.17.93 ↗
61. Effect of Element Distribution on Strength in Fly Ash Geopolymers
62. Flexible Aluminum Coordination in Alumino-Silicates. structure of Zeolites H-USY and Amorphous Silica-Alumina10.1021/jp030094+ ↗
63. Dehydroxylation of kaolinite to metakaolin-a molecular dynamics study10.1039/C0JM01748E ↗
64. Microstructural and mechanical properties of poly(sialate-siloxo) networks obtained using metakaolins from kaolin and halloysite as aluminosilicate sources: A comparative study10.1016/j.clay.2020.105448 ↗
65. Structural characterization of organo-montmorillonites prepared from a series of primary alkylamines salts: Mid-IR and near-IR study10.1016/j.clay.2019.04.016 ↗
66. The effect of composition and temperature on the properties of fly ash- and kaolinite-based geopolymers10.1016/S1385-8947(02)00025-6 ↗
67. Davidovits, J. (2008). Geopolymer Chemistry and Applications, Geopolymer Institute.
68. FT-IR and 29Si-NMR for evaluating aluminium–silicate precursors for geopolymers10.1617/s11527-014-0432-2 ↗
69. Quantitative study of the reactivity of fly ash in geopolymerization by FTIR
70. Effect of silicate activator pH on the leaching and material characteristics of waste-based inorganic polymers10.1016/S0892-6875(01)00002-4 ↗