Experimental-Numerical Investigation of a Steel Pipe Repaired with a Composite Sleeve
Source abstract
Abstract
Pressure vessels are subjected to deterioration and damage, which can significantly reduce their strength and loading capabilities. Among several procedures nowadays available to repair damaged steel pipelines, composite-repairing systems have become popular over the past few years to restore the loading capacity of damaged pipelines. This study reports a numerical-experimental investigation performed for a composite-repaired pipeline made of API 5L X60 steel. An experimental burst test was carried out on a 4 m long pipe section, closed by two lateral caps, and tested up to failure by means of high-pressure water. In parallel, the test was numerically replicated through a FEM model of the composite-repaired steel tank, allowing for a cross-comparison of results. It was found that the composite repairing system has almost eliminated both the noteworthy thickness reduction of 80% and the related stress concentrations in the pipe body. These outcomes allow for a better understanding of these repairing procedures in order to drive their subsequent optimization.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Structural Integrity and Reliability Analysis · Fatigue and fracture mechanics · Material Properties and Failure Mechanisms
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Department of Mechanical Engineering, Tarbiat Modares University, Tehran 1411713116, Iran
Department of Mechanical Engineering, Meybod University, Yazd 8961699557, Iran
A. Leon Linton Department of Mechanical, Robotics and Industrial Engineering, Lawrence Technological University, Southfield, MI 48075, USA
Department of Industrial Engineering, University of Salerno, Via G. Paolo II, 132, 84084 Fisciano, SA, Italy
References (47)
Show source-provided references
1. Pridmore, A.B., and Ojdrovic, R.P. (2015). Trenchless Repair of Concrete Pipelines Using Fiber-Reinforced Polymer Composites. Rehabilitation of Pipelines Using Fiber-Reinforced Polymer (FRP) Composites, Woodhead Publishing.10.1016/B978-0-85709-684-5.00002-3 ↗
2. An assessment of the effect of steel pipeline wall losses on the maximum allowable operating pressure of a gas pipeline
3. EMAT technology applied to high pressure gas pipelines diagnostic, SIGMA NOT Publishing House
4. Failure analysis and design of grouted fibre-composite repair system for corroded steel pipes10.1016/j.engfailanal.2020.104979 ↗
5. Composite repair of through-wall defects in pipework—Analytical and numerical models with respect to ISO/TS 24817
6. Maintenance planning under imperfect inspections of corroded pipelines10.1016/j.ijpvp.2013.01.009 ↗
7. Composite repair of pipelines, considering the effect of live pressure—Analytical and numerical models with respect to ISO/TS 24817 and ASME PCC-210.1016/j.compositesb.2013.10.035 ↗
8. Effectiveness of using fibre-reinforced polymer composites for underwater steel pipeline repairs10.1016/j.compstruct.2012.12.019 ↗
9. Alexander, C. (2014, January 20–24). The Role of Composite Repair Technology in Rehabilitating Piping and Pipelines. Proceedings of the ASME 2014 Pressure Vessels and Piping Conference (PVP 2014), Anaheim, CA, USA.10.1115/PVP2014-28257 ↗
10. Burst strength of carbon fibre reinforced polyethylene strip pipeline repair system—A numerical and experimental approach10.1177/0021998314525652 ↗
11. Effect of hygrothermal conditioning on the mechanical and thermal properties of epoxy grouts for offshore pipeline rehabilitation10.3934/matersci.2016.3.832 ↗
12. Stress corrosion cracking behavior of welding joint of high strength steel10.1088/1757-899X/1038/1/012055 ↗
13. Kiefner, J.F., and Duffy, A.R. (1975). A Study of Two Methods for Repairing Defects in Line Pipe, American Gas Association. AGA Cat. No. L22275.10.55274/R0011304 ↗
14. Kiefner, J.F., and Whitacre, G.R. (1978). Further Studies of Two Methods for Repairing Defects in Line Pipe, American Gas Association. AGA Cat No. L22279.10.55274/R0010407 ↗
15. Performance of steel pipe reinforced with composite sleave10.1016/j.compstruct.2017.02.032 ↗
16. Behaviour of steel pipelines with composite repairs analyzed using experimental and numerical approaches10.1016/j.tws.2019.03.023 ↗
17. Alexander, C. (2009, January 21–22). Overview and recent advances in application of composite materials for repair of transmission pipelines: Evaluation of test results and ongoing research. Proceedings of the Evaluation and Rehabilitation of Pipelines Conference, Pittsburgh, PA, USA.
18. Alexander, C., and Bedoya, J. (October, January 27). Repair of dents subjected to cyclic pressure service using composite materials. Proceedings of the 8th International Pipeline Conference IPC2010, Calgary, AB, Canada.10.1115/IPC2010-31524 ↗
19. Karbhari, V.M. (2015). Comparison of fiber-reinforced polymer wrapping versus steel sleeves for repair of pipelines. Rehabilitation of Pipelines Using Fiber-Reinforced Polymer (FRP) Composites, Woodhead Publishing.
20. Karbhari, V.M. (2015). Fiber wrapped steel pipes for high-pressure pipelines. Rehabilitation of Pipelines Using Fiber-Reinforced Polymer (FRP) Composites, Woodhead Publishing.
21. An alternative methodology to repair localized corrosion damage in metallic pipelines with epoxy resins10.1016/j.matdes.2009.02.026 ↗
22. Evaluation of the response of fibre reinforced composite repair of steel pipeline subjected to puncture from excavator tooth10.1016/j.compstruct.2018.05.065 ↗
23. Experimental and numerical study of steel pipe with part-wall defect reinforced with fibre glass sleeve10.1016/j.ijpvp.2016.12.008 ↗
24. Analytical solutions for yield onset achievement in FGM thick walled cylindrical tubes undergoing thermomechanical loads10.1016/j.compositesb.2017.02.023 ↗
25. Yield Onset of Thermo-Mechanical Loading of FGM Thick Walled Cylindrical Pressure Vessels
26. Mehditabar, A., Sadrabadi, S.A., Sepe, R., Armentani, E., Walker, J., Citarella, R., and Sadrabadi, S.A. (2020). Influences of Material Variations of Functionally Graded Pipe on the Bree Diagram. Appl. Sci., 10.10.3390/app10082936 ↗
27. Three-dimensional magneto-thermo-elastic analysis of functionally graded cylindrical shell10.1007/s10483-017-2186-6 ↗
28. Polymer-based composite repair system for severely corroded circumferential welds in steel pipes10.1016/j.engfailanal.2017.08.001 ↗
29. Mehditabar, A., Sadrabadi, S.A., and Walker, J. (2021). Thermal buckling analysis of a functionally graded microshell based on higher-order shear deformation and modified couple stress theories. Mech. Based Des. Struct. Mach., 1–19.10.1080/15397734.2021.1908145 ↗
30. Elasto-Plastic Behavior Analysis and Yield Onset in FG Cylindrical Tubes under Mechanical and Thermal Loads
31. Behavior of Fgm Spherical Vessels under Internal Pressure and Temperature Difference
32. FGM elastoplastic analysis under thermomechanical loading10.1016/j.ijpvp.2013.04.028 ↗
33. Experimental and numerical study of stress-strain state of pressurized cylindrical shells with external defects10.1016/j.engfailanal.2009.09.011 ↗
34. Effect of interaction between corrosion defects on failure pressure of thin wall steel pipeline10.1016/j.ijpvp.2016.01.002 ↗
35. Investigation of pressurized elbows containing interacting corrosion defects10.1016/j.ijpvp.2014.08.002 ↗
36. Reliability and failure pressure prediction of various grades of pipeline steel in the presence of corrosion defects and pre-strain10.1016/j.ijpvp.2011.09.008 ↗
37. Finite element analysis of the integrity of an API X65 pipeline with a longitudinal crack repaired with single- and double-bonded composites10.1016/j.compositesb.2015.03.008 ↗
38. Efficient FEM-DBEM coupled approach for crack propagation simulations10.1016/j.tafmec.2017.04.003 ↗
39. Fatigue life assessment in lateral support element of a magnet for nuclear fusion experiment “Wendelstein 7-X”10.1016/j.engfracmech.2017.04.033 ↗
40. LCF assessment on heat shield components of nuclear fusion experiment “Wendelstein 7-X” by critical plane criteria10.1016/j.prostr.2017.12.033 ↗
41. Dassault Systemes (2014). ABAQUS User’s and Theory Manuals, HKS Inc.. Version 6.14.
42. FEM-DBEM approach for crack propagation in a low pressure aeroengine turbine vane segment10.1016/j.tafmec.2016.05.004 ↗
43. FEM-DBEM approach to simulate crack propagation in a turbine vane segment undergoing a fatigue load spectrum10.1016/j.prostr.2018.11.070 ↗
44. Multiple Crack Propagation with Dual Boundary Element Method in Stiffened and Reinforced Full Scale Aeronautic Panels10.4028/www.scientific.net/KEM.560.129 ↗
45. Stochastic approach to fatigue crack-growth simulation for a railway axle under input data variability10.1016/j.ijfatigue.2020.106044 ↗
46. Mixed-mode crack growth simulation in aviation engine compressor disk10.1016/j.engfracmech.2021.107617 ↗
47. Numerical investigation on the fracture failure of a railway axle10.1016/j.engfailanal.2021.105680 ↗