journal article·2020-09-10Open access

A Critical Review of SCWG in the Context of Available Gasification Technologies for Plastic Waste

Benedetta Ciuffi, David Chiaramonti, Andrea Maria Rizzo, Marco Frediani, Luca Rosi

Applied Sciences· Volume 10· Issue 18

Abstract

End of life packaging is nowadays one of the major environmental problems due to its short usage time, the low biodegradability, and the big volume occupied. In this context, gasification is one of the most promising chemical recycling techniques. Some non-recyclable or non-compostable waste gasification plants are already operating such as Enerkem Alberta Biofuels in Canada or the Sierra’s FastOx Pathfinder in California. In this review, we have examined works about plastic gasification from the last fifteen years with a specific focus on polyolefin (PP, PE), plastics mix, and co-gasification of plastic with biomass. For each of these, the best operating conditions were investigated. A very in-depth section was dedicated to supercritical water gasification (SCWG). The most used reactors in gasification processes are fluidized bed reactors together with air or steam as gasifying agents. Tar removal is commonly performed using olivine, dolomite, or nickel based catalysts. SCWG has numerous advantages including the inhibition of tar and coke formation and can be used to remove microplastics from the marine environment. In co-gasification of plastic material with coal or biomass, synergistic effects are observed between the raw materials, which improve the performance of the process, allowing to obtain higher gas yields and a syngas with a high energy content.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Thermochemical Biomass Conversion Processes · Subcritical and Supercritical Water Processes · Environmental remediation with nanomaterials

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Department of Chemistry “Ugo Schiff”, University of Florence, Via della Lastruccia 3-13, Sesto Fiorentino, 50019 Florence, Italy

“Galileo Ferraris” Energy Department, Polytechnic of Turin, Corso Duca degli Abruzzi 24, I-10129 Torino, Italy

Renewable Energy Consortium for Research and Demonstration-RE-CORD, Viale Kennedy 182, Scarperia e San Piero, 50038 Florence, Italy

Funding

Fondazione Cassa di Risparmio di Firenze

References (100+)

Show source-provided references
1. Our plastic age10.1098/rstb.2009.0054 ↗
2. Current state and future prospects of plastic waste as source of fuel: A review10.1016/j.rser.2015.04.063 ↗
3. Parlamento Europeo e Consiglio (2020, April 04). Direttiva 2008/98/CE. Available online: https://eur-lex.europa.eu/legal-content/IT/TXT/PDF/?uri=CELEX:02008L0098-20150731&from=ET.
4. (2020, April 04). Plastics—The Facts-2019. Available online: https://www.plasticseurope.org/it/resources/publications/1804-plastics-facts-2019.
5. (2020, April 04). Polymers for Innovative Food Packaging. Available online: https://web.wpi.edu/Pubs/E-project/Available/E-project-050610124822/unrestricted/Polymers_for_Innovative_Food_Packaging.pdf.
6. Ghosh, A. (2015). Basics of polymer packaging. Adv. Polym. Technol., 1–18.10.1007/978-1-56990-577-7_1 ↗
7. Wikström, F., Williams, H., Trischler, J., and Rowe, Z. (2019). The importance of packaging functions for food waste of different products in households. Sustainability, 11.10.3390/su11092641 ↗
8. Subramanian, S.M. (2016). Environmental impacts of packaging materials. Environmental Footprints of Packaging, Springer. [1st ed.].
9. Synthetic polymers in the marine environment: A rapidly increasing, long-term threat10.1016/j.envres.2008.07.025 ↗
10. Kutz, M. (2007). The environmental impacts of packaging. Environmentally Conscious Materials and Chemicals Processing, John Wiley & Sons, Inc.10.1002/9780470168219 ↗
11. Significant plastic accumulation on the Cocos (Keeling) Islands, Australia10.1038/s41598-019-43375-4 ↗
12. Micro(nano)plastics: A threat to human health?10.1016/j.coesh.2017.10.003 ↗
13. (2020, April 20). A European Strategy for Plastics in a Circular Economy. Brussels. Available online: https://ec.europa.eu/environment/circular-economy/pdf/plastics-strategy-brochure.pdf.
14. Evingür, G.A. (2018). Thermoplastic Recycling: Properties, Modifications, and Applications. Thermosoftening Plastics, Intech Open.
15. Mechanistic implications of plastic degradation10.1016/j.polymdegradstab.2007.11.008 ↗
16. Recycling and recovery routes of plastic solid waste (PSW): A review10.1016/j.wasman.2009.06.004 ↗
17. A review on tertiary recycling of high-density polyethylene to fuel10.1016/j.resconrec.2011.05.005 ↗
18. Grigore, M.E. (2017). Methods of recycling, properties and applications of recycled thermoplastic polymers. Recycling, 2.10.3390/recycling2040024 ↗
19. A review on pyrolysis of plastic wastes10.1016/j.enconman.2016.02.037 ↗
20. Recent advances in the gasification of waste plastics. A critical overview10.1016/j.rser.2017.09.032 ↗
21. The valorization of plastic solid waste (PSW) by primary to quaternary routes: From re-use to energy and chemicals10.1016/j.pecs.2009.09.001 ↗
22. Mechanical and chemical recycling of solid plastic waste10.1016/j.wasman.2017.07.044 ↗
23. A review on subcritical and supercritical water gasification of biogenic, polymeric and petroleum wastes to hydrogen-rich synthesis gas10.1016/j.rser.2019.109546 ↗
24. Speight, J.G. (2014). Feedstocks. Gasification of Unconventional Feedstocks, Gulf Professional Publishing.10.1016/B978-0-12-799911-1.00001-7 ↗
25. Gasification of plastic waste as waste-to-energy or waste-to-syngas recovery route
26. Faria, J., and Ruiz-Ramiro, M.P. (2015). Solid Waste as a Renewable Resource: Methodologies, Apple Academic Press. [1st ed.].
27. Co-gasification of biomass and plastics: Pyrolysis kinetics studies, experiments on 100 kW dual fluidized bed pilot plant and development of thermodynamic equilibrium model and balances10.1016/j.biortech.2014.03.121 ↗
28. Khallaf, M. (2011). Air pollution control in municipal solid waste incinerators. The Impact of Air Pollution on Health, Economy, Environment and Agricultural Sources, Intech Open.10.5772/1000 ↗
29. Treatment and use of air pollution control residues from MSW incineration: An overview10.1016/j.wasman.2007.08.030 ↗
30. Dioxins and furans: A review from chemical and environmental perspectives10.1016/j.teac.2017.12.001 ↗
31. Plastics recycling: Challenges and opportunities10.1098/rstb.2008.0311 ↗
32. Speight, J.G. (2014). Gasifier types. Gasif. Unconv. Feedstocks, 54–90.10.1016/B978-0-12-799911-1.00003-0 ↗
33. Saghir, M., Rehan, M., and Nizami, A.S. (2018). Recent trends in gasification based waste-to-energy. Gasification for Low-Grade Feedstock, InTech.10.5772/intechopen.74487 ↗
34. Brown, R.C. (2019). Thermochemical Processing of Biomass: Conversion into Fuels, Chemicals and Power, Wiley. [2nd ed.].10.1002/9781119417637 ↗
35. Ghenai, C. (2019). Syngas production, properties, and its importance. Sustainable Alternative Syngas Fuel, Intech Open.
36. (2020, April 26). Syngas & Derivatives Market. Available online: https://www.marketsandmarkets.com/Market-Reports/syngas-market-1178.html.
37. Influence of syngas composition on the transient behavior of a Fischer-Tropsch continuous slurry reactor10.1016/j.cattod.2005.07.126 ↗
38. Transient studies of the elementary steps of Fischer-Tropsch synthesis10.1016/j.cattod.2005.07.122 ↗
39. Fischer-Tropsch synthesis: Effect of ammonia in syngas on the Fischer-Tropsch synthesis performance of a precipitated iron catalyst10.1016/j.jcat.2015.04.004 ↗
40. Tsiamis, D.A., and Castaldi, M.J. (2018). The Effects of Non-Recycled Plastic (NRP) on Gasification: A Quantitative Assessment, Earth Engineering Center City University of New York.
41. (2020, April 26). Enerkem. Available online: https://enerkem.com/company/facilities-projects/.
42. Thermochemical Biomass Gasification: A Review of the Current Status of the Technology10.3390/en20300556 ↗
43. Air gasification of polypropylene plastic waste in fluidized bed gasifier10.1016/j.enconman.2006.09.004 ↗
44. Ruan, R. (2019). Biofuels: Introduction. Biofuels: Alternative Feedstocks and Conversion Processes for the Production of Liquid and Gaseous Biofuels, Elsevier.10.1016/B978-0-12-816856-1.00001-4 ↗
45. Biomass gasification thermodynamic model including tar and char
46. Sustainable energy: A review of gasification technologies10.1016/j.rser.2012.04.023 ↗
47. Review of gasification fundamentals and new findings: Reactors, feedstock, and kinetic studies10.1016/j.ces.2016.03.037 ↗
48. Plastic waste elimination by co-gasification with coal and biomass in fluidized bed with air in pilot plant10.1016/j.fuproc.2005.09.006 ↗
49. Thermochemical routes for the valorization of waste polyolefinic plastics to produce fuels and chemicals. A review10.1016/j.rser.2017.01.142 ↗
50. Characterization of tars from biomass gasification: Effect of the operating conditions10.1016/j.energy.2012.12.005 ↗
51. Low-temperature catalytic conversion of lignite: 1. Steam gasification using potassium carbonate supported on perovskite oxide10.1016/j.jiec.2013.04.004 ↗
52. Effect of steam content in the air-steam flow on biomass entrained flow gasification10.1016/j.fuproc.2012.01.030 ↗
53. Kinetic models for the oxy-fuel combustion of coal and coal/biomass blend chars obtained in N2 and CO2 atmospheres10.1016/j.energy.2012.10.033 ↗
54. Van Krevelen, D.W., and Te Nijenhuis, K. (2009). Thermal decomposition. Properties of Polymers, Elsevier Science. [4th ed.].10.1016/B978-0-08-054819-7.00021-2 ↗
55. Molecular-Level Kinetic Modeling of the Gasification of Common Plastics10.1021/acs.energyfuels.5b02047 ↗
56. Characterization of the waxes obtained by the pyrolysis of polyolefin plastics in a conical spouted bed reactor10.1016/j.jaap.2011.12.012 ↗
57. European trends in the feedstock recycling of plastic wastes
58. Quantitative analysis of random scission and chain-end scission in the thermal degradation of polyethylene10.1016/j.polymdegradstab.2010.04.020 ↗
59. Operating conditions for the pyrolysis of poly-(ethylene terephthalate) in a conical spouted-bed reactor10.1021/ie900557c ↗
60. Energy and exergy characteristics of syngas produced from air gasification of walnut sawdust in an entrained flow reactor10.1504/IJEX.2017.085772 ↗
61. Oxygen gasification of municipal solid waste in a fixed-bed gasifier10.1016/j.cjche.2014.06.026 ↗
62. Exergy analysis of biomass utilization via steam gasification and partial oxidation10.1016/j.tca.2012.03.013 ↗
63. Determination of the intrinsic reactivities for carbon dioxide gasification of rice husk chars through using random pore model10.1016/j.biortech.2016.07.057 ↗
64. Supercritical water gasification research and development in China10.1016/j.supflu.2014.09.023 ↗
65. Energy generation by air gasification of two industrial plastic wastes in a pilot scale fluidized bed reactor10.1016/j.energy.2014.01.084 ↗
66. Manipulating the H2/CO ratio from dry reforming of simulated mixed waste plastics by the addition of steam10.1016/j.fuproc.2016.09.016 ↗
67. Syngas from steam gasification of polyethylene in a conical spouted bed reactor10.1016/j.fuel.2013.03.022 ↗
68. Influence of the effective parameters on H2:CO ratio of syngas at low-temperature gasification
69. Effect of H2:CO ratio in syngas on the performance of a dual fuel diesel engine operation10.1016/j.applthermaleng.2011.08.021 ↗
70. A review on gasification of biomass10.1016/j.rser.2007.07.001 ↗
71. The Environment and Industry Council (EPIC) (2004). The gasification of residual plastics derived from municipal recycling facilities. Can. Plast. Ind. Assoc., 1, 1–11.
72. Study of the effects of temperature on syngas composition from pyrolysis of wood pellets using a nitrogen plasma torch reactor10.1016/j.jaap.2018.01.014 ↗
73. Modeling and comparative assessment of bubbling fluidized bed gasification system for syngas production–a gateway for a cleaner future in Pakistan10.1080/09593330.2017.1340350 ↗
74. Bermudez, J.M., and Fidalgo, B. (2016). Production of bio-syngas and bio-hydrogen via gasification. Handbook of Biofuels Production, Elsevier. [2nd ed.].10.1016/B978-0-08-100455-5.00015-1 ↗
75. Gasification and effect of gasifying temperature on syngas quality and tar generation: A short review10.1063/1.4704254 ↗
76. High-temperature entrained flow gasification of biomass10.1016/j.fuel.2011.10.063 ↗
77. Characterization of pyrolysis products from slow pyrolysis of live and dead vegetation native to the southern United States10.1016/j.fuel.2018.08.112 ↗
78. Elorf, A., Kandasamy, J., Belandria, V., Bostyn, S., Sarh, B., and Gökalp, I. (2019). Heating rate effects on pyrolysis, gasification and combustion of olive waste. Biofuels.10.1080/17597269.2019.1594598 ↗
79. Optimum equivalence ratio of biomass gasification process based on thermodynamic equilibrium model10.1016/j.egypro.2015.11.528 ↗
80. Effects of temperature and equivalence ratio on carbon nanotubes and hydrogen production from waste plastic gasification in fluidized bed10.1021/acs.energyfuels.7b04109 ↗
81. Scale-up of bubbling fluidized bed reactors—A review10.1016/j.powtec.2011.10.004 ↗
82. Catalytic air gasification of plastic waste (polypropylene) in a fluidized bed. Part II: Effects of some operating variables on the quality of the raw gas produced using olivine as the in-bed material10.1021/ie200145p ↗
83. Thermal valorization of post-consumer film waste in a bubbling bed gasifier10.1016/j.wasman.2013.03.016 ↗
84. Tar removal during the fluidized bed gasification of plastic waste10.1016/j.wasman.2008.05.010 ↗
85. Gasification of polyethylene in a bubbling fluidized bed operated with the air staging10.1016/j.fuel.2012.12.049 ↗
86. Co-gasification of coal, plastic waste and wood in a bubbling fluidized bed reactor10.1016/j.fuel.2010.05.019 ↗
87. Effect of gasification agent on co-gasification of rice production wastes mixtures10.1016/j.fuel.2016.04.048 ↗
88. A novel Ni-Mg-Al-CaO catalyst with the dual functions of catalysis and CO2 sorption for H2 production from the pyrolysis-gasification of polypropylene10.1016/j.fuel.2009.10.020 ↗
89. Production of low-tar producer gas from air gasification of mixed plastic waste in a two-stage gasifier using olivine combined with activated carbon10.1016/j.energy.2013.06.021 ↗
90. H2 production from co-pyrolysis/gasification of waste plastics and biomass under novel catalyst Ni-CaO-C10.1016/j.cej.2019.122947 ↗
91. Hydrogen production by high density polyethylene steam gasification and in-line volatile reforming10.1021/acs.iecr.5b02413 ↗
92. Fluidization and spouting of fine particles: A comparison10.1155/2013/369380 ↗
93. Design and operation of a conical spouted bed reactor pilot plant (25 kg/h) for biomass fast pyrolysis10.1016/j.fuproc.2013.02.022 ↗
94. The IAPWS formulation 1995 for the thermodynamic properties of ordinary water substance for general and scientific use
95. Subcritical water as reaction environment: Fundamentals of hydrothermal biomass transformation10.1002/cssc.201000341 ↗
96. Basu, P., and Mettanant, V. (2009). Biomass gasification in supercritical water—A review. Int. J. Chem. React. Eng., 7.10.2202/1542-6580.1919 ↗
97. Supercritical water gasification of biomass for hydrogen production: Variable of the process10.5923/j.fph.20150503.05 ↗
98. Supercritical water gasification of biomass model compounds: A review10.1016/j.rser.2019.109529 ↗
99. Heidenreich, S., Müller, M., and Foscolo, P.U. (2016). New and improved gasification concepts. Advanced Biomass Gasification, Elsevier.10.1016/B978-0-12-804296-0.00006-3 ↗
100. Supercritical water gasification of biomass: A state-of-the-art review of process parameters, reaction mechanisms and catalysis10.1039/C8SE00565F ↗