Uniaxial Properties versus Temperature, Creep and Impact Energy of an Austenitic Steel
Source abstract
Abstract
Abstract In this paper, uniaxial material properties, creep resistance and impact energy of the austenitic heat-resistant steel (1.4841) are experimentally determined and analysed. Engineering stress–strain diagrams and uniaxial short-time creep curves are examined with computer-controlled testing machine. Impact energy has been determined and fracture toughness assessed. Investigated data are shown in the form of curves related to ultimate tensile strength, yield strength, modulus of elasticity and creep resistance. All of these experimentally obtained results are analysed and may be used in the design process of the structure where considered material is intended to be applied. Based on these results, considered material may be classified as material of high tensile strength (688 MPa/293 K; 326 MPa/923 K) and high yield strength (498 MPa/293 K; 283 MPa/923 K) as well as satisfactory creep resistance (temperature/stress $ \to $strain (%) at 1,200 min: 823 K/167 MPa $ \to $0.25 %; 923 K/85 MPa $ \to $0.2 %).
Source: crossref · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: High Temperature Alloys and Creep · Fire effects on concrete materials · Fatigue and fracture mechanics
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Department of Engineering Mechanics, Faculty of Engineering, University of Rijeka, Vukovarska 58, 51000 Rijeka, Croatia
Faculty of Maritime Studies, University of Rijeka, Studentska ulica 2, 51000 Rijeka, Croatia
References (42)
Show source-provided references
1. [1] J.A. Collins, Failures of Materials in Mechanical Design, John Wiley & Sons, New York (1993).
2. [2] C.R. Brooks and A. Choudhury, Failure Analysis of Engineering Materials, McGraw-Hill, USA (2002).
3. [3] B. Farahmand, G. Bockrath and J. Glassco, Fatigue and Fracture Mechanics of High Risk Parts, Chapman & Hall, New York (1997).10.1007/978-1-4615-6009-8 ↗
4. [4] R.P. Solecki and R. Conant, Advanced Mechanics of Materials, Oxford University Press, New York (2003).
5. [5] V. Raghavan, Materials Science and Engineering, Prentice-Hall of India, New Delhi (2004).
6. [6] O. Caty, E. Maire, T. Douillard, P. Bertino, R. Dejaeger and R. Bouchet, Mater. Lett., 63 (2009) 1131–1134.10.1016/j.matlet.2008.10.020 ↗
7. [7] K. Bobzin, T. Schläfer and N. Kopp, Int. J. Mater. Res., 102 (2011) 972–976.10.3139/146.110550 ↗
8. [8] R. Bauer, M. Baccalaro, L.P.H. Jeurgens, M. Pohl and E.J. Mittemeijer, Oxid. Met., 69 (2008) 265–285.10.1007/s11085-008-9097-y ↗
9. [9] K. Bobzin, N. Bagcivan, K. Kopp and C. Weiler, Proceedings of the 5th International Brazing and Soldering Conference, April 22–25, 2012, Las Vegas, Nevada, USA (2012), pp. 433–436.
10. [10] A. Kaletsch, E.M. Pfaff and C. Broeckmann, Adv. Eng. Mater., 16 (2014) 1430–1436.10.1002/adem.201400102 ↗
11. [11] J. Brnic, G. Turkalj, M. Canadija and D. Lanc, J. Constr. Steel Res., 67 (2011) 1948–1952.10.1016/j.jcsr.2011.06.011 ↗
12. [12] Y.C. Lin, Y.Q. Jiang, H.M. Zhou and G. Liu, J. Mater. Eng. Perform., 23 (2014) 4350–4357.10.1007/s11665-014-1191-5 ↗
13. [13] J. Brnic, G. Turkalj, S. Krscanski, D. Lanc, M. Canadija and M. Brcic, Mater. Design, 63 (2014) 508–518.10.1016/j.matdes.2014.06.051 ↗
14. [14] J. Brnic, G. Turkalj and M. Canadija, Steel Comp. Struct., 17 (2014) 549–560.10.12989/scs.2014.17.5.549 ↗
15. [15] Y. Cai and B. Young, J. Constr. Steel Res., 104 (2014) 49–63.10.1016/j.jcsr.2014.09.015 ↗
16. [16] D.Q. Peng, S.L. Hu, P.Z. Zhang and H. Wang, J. Wuhan Univ. Tech., 34 (2012) 6–9.
17. [17] J. Brnic, M. Canadija, G. Turkalj, D. Lanc, T. Pepelnjak, B. Barišić, G. Vukelić and M. Brcic, Mater. Manuf. Proc., 24 (2009) 1–5.10.1080/10426910902809800 ↗
18. [18] J. Brnić, G. Turkalj, D. Lanc, M. Canadija, M. Brcic, G. Vukelic and N. Munjas, Constr. Build. Mater., 44 (2013) 293–301.10.1016/j.conbuildmat.2013.02.080 ↗
19. [19] M. Cowan and K. Khandelwal, Eng. Struct., 80 (2014) 426–434.10.1016/j.engstruct.2014.09.020 ↗
20. [20] J. Brnic, M. Canadija, G. Turkalj and D. Lanc, J. Eng. Mater. Technol., 132 (2010) 021004-1–021004-6.10.1115/1.4000669 ↗
21. [21] J. Brnic, M. Canadija, G. Turkalj and D. Lanc, J. Eng. Mech., 136 (2009) 1083–1089.10.1061/(ASCE)EM.1943-7889.0000152 ↗
22. [22] J. Brnic, G. Turkalj, M. Canadija and J. Niu, Mater. Sci. Eng. A, 600 (2014) 47–52.10.1016/j.msea.2014.01.097 ↗
23. [23] J. Brnic, G. Turkalj, D. Lanc, M. Canadija, M. Brcic and G. Vukelic, J. Constr. Steel Res., 95 (2014) 81–89.10.1016/j.jcsr.2013.11.024 ↗
24. [24] M. Canadija, X. Guo, D. Lanc, W. Yang and J. Brnic, Mater. Design., 59 (2014) 287–295.10.1016/j.matdes.2014.03.001 ↗
25. [25] D. Klobčar, L. Kosec, B. Kosec and J. Tušek, Eng. Failure Anal., 20 (2012) 45–53.10.1016/j.engfailanal.2011.10.005 ↗
26. [26] M. Milutinovic, D. Movrin and T. Pepelnjak, Int. J. Adv. Manuf. Technol., 58 (2012) 895–906.10.1007/s00170-011-3457-5 ↗
27. [27] J. Brnic, G. Turkalj, M. Canadija, D. Lanc and M. Brcic, High Temp. Mater. Process., 27 (2015) 27–34.10.1515/htmp-2014-0011 ↗
28. [28] J. Brnic, G. Turkalj, J. Niu, M. Canadija and D. Lanc, Mater. Design, 47 (2013) 497–504.10.1016/j.matdes.2012.12.037 ↗
29. [29] J. Brnic, G. Turkalj, M. Canadija and D. Lanc, J. Constr. Steel Res., 67 (2011) 1948–1952.10.1016/j.jcsr.2011.06.011 ↗
30. [30] J. Brnic, G. Turkalj, M. Canadija, D. Lanc and S. Krscanski, Mech. Time-Dep. Mater., 15 (2011) 341–352.10.1007/s11043-011-9137-x ↗
31. [31] Y. Gorash, H. Altenbach and G. Lvov, J. Strain Anal. Eng. Design, 47 (2012) 229–243.10.1177/0309324712440764 ↗
32. [32] N. Herakovič and T. Bevk, Mater. Tehnol., 44 (2010) 37–40.
33. [33] P. Podrzaj and S. Simoncic, Sci. Technol. Weld. Join., 18 (2013) 551–557.
34. [34] R. Šturm, I. Grum and S. Božić, Laser Eng., 22 (2011) 47–61.
35. [35] J. Brnić, G. Turkalj, M. Canadija, S. Krscanski, M. Brcic and D. Lanc, Mater. Design, 69 (2015) 219–229.10.1016/j.matdes.2014.12.062 ↗
36. [36] Annual Book of ASTM Standards, Metal Test Methods and Analytical Procedures, Vol. 03.01, ASTM International, Baltimore (2012).
37. [37] N.R. Draper and H. Smith, Applied Regression Analysis, Wiley-Interscience Publications, USA (1998).10.1002/9781118625590 ↗
38. [38] M.P. Blinn and R.A. Williams, in ASTM Handbook, Vol. 20, Materials Selection and Design edited by G.E. Dieter, ASM International, USA (1997), pp. 533–544.
39. [39] T.L. Anderson, Fracture Mechanics, CRC Press, Boca Raton (2005).
40. [40] Y.J. Chao, J.D. Ward and R.G. Sands, Mater. Design, 28 (2007) 551–557.10.1016/j.matdes.2005.08.009 ↗
41. [41] J. Brnic, G. Turkalj, M. Canadija, D. Lanc and S. Krscanski, Responses of Austenitic Stainless Steel American Iron and Steel Institute (AISI) 303 (1.4305) Subjected to Different Environmental Conditions, J. of testing and evaluation. 40 (2012) 2;319–328.10.1520/JTE104160 ↗
42. [42] J. Brnic, G. Turkalj, D. Lanc, M. Canadija, M. Brcic, G. Vukelic, N. Munjas, Testing and Analysis of X39CrMo17-1 Steel Properties, Construction and building materials, 44 (2013) 293–301.10.1016/j.conbuildmat.2013.02.080 ↗