journal article·2026-03-23

Development of 3D printing filament from recycled HDPE injection waste

Tilly Zi Li Khoo, Ming Yeng Chan, Seong Chun Koay, Thai Kiat Ong, Shuh Huey Ho

Publisher page

Abstract

The present study focused on the fabrication and characterization of three-dimensional (3D) printing filament produced from high-density polyethylene waste (rHDPE). The rHDPE was sourced from injection-moulded waste such as sprues, gates and runners. Due to the unsuitability of injection grade of polymer for extrusion process, injection-grade rHDPE was blended with extrusion-grade high-density polyethylene (HDPE) materials. Different blend ratios of injection-grade rHDPE to extrusion-grade HDPE (100:0, 60:40, 50:50, and 40:60) were prepared and extruded into 3D printing filaments. The filament characterization including filament diameter consistency, filament ovality, and melt flow index were evaluated, while the thermal stability of the blends was analysed using thermogravimetric analysis. Among the blend ratios, the 50:50 (injection-grade rHDPE: extrusion-grade HDPE) blend demonstrated the starting ratio for producing 3D printing filament with consistent filament diameter and was therefore selected for 3D printing tensile specimens for tensile testing, indicating its suitability for 3D printing applications. Tensile specimens printed from this 50:50 blend ratio filament were tested at three different infill densities (20%, 60%, and 100%). Furthermore, the tensile properties of 3D-printed parts printed from 50:50 rHDPE blend filament were compared with those of commercial virgin polylactic acid, polyethylene terephthalate glycol, and HDPE filaments.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Additive Manufacturing and 3D Printing Technologies · Polymer crystallization and properties · Injection Molding Process and Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Tunku Abdul Rahman University of Management and Technology Department of Manufacturing Technology, Faculty of Engineering and Technology, , Kuala Lumpur,

Tunku Abdul Rahman University of Management and Technology Centre for Advanced Materials, Faculty of Engineering and Technology, , Kuala Lumpur,

Universiti Tunku Abdul Rahman Centre for Sustainable Mobility Technologies, Department of Mechanical and Materials Engineering, Lee Kong Chian Faculty of Engineering and Science, , Kajang,

References (16)

Show source-provided references
1. Matthews G (2023) HDPE Recycling. BusinessWaste.co.uk. See Link to the cited article (accessed02/03/2026).
2. 3D polymer composite filament development from post-consumer polypropylene and disposable chopstick fillers10.1002/vnl.22026 ↗
3. The plastic waste problem in Malaysia: management, recycling and disposal of local and global plastic waste10.1007/s42452-021-04234-y ↗
4. Comparative LCAs for curbside recycling versus either landfilling or incineration with energy recovery10.1065/lca2004.09.180.10 ↗
5. Plastics recycling: challenges and opportunities10.1098/rstb.2008.0311 ↗
6. 3D printing of high-density polyethylene by fused filament fabrication10.1016/j.addma.2019.05.003 ↗
7. A comparative study in fused filament fabrication using commercial and recycled high-density polyethylene10.21315/jps2025.36.3.1 ↗
8. Effects of filament diameter tolerances in fused filament fabrication10.14434/iujur.v2i1.20917 ↗
9. Preparation and characterization of PLA filaments for FDM 3D printing
10. Ritcher A (2019) The importance of ovality in 3D printing filament. MatterHackers. Link to the cited article (accessed02/03/2026).
11. A review on the fused deposition modeling (FDM) 3D printing: filament processing, materials, and printing parameters
12. Development and preliminary analysis of 3D printing filament from post-consumer polypropylene10.58915/ijneam.v18iDecember.2812 ↗
13. Pritchard E (2024) MFI testing: a key validation step for novel filament extrusion. 3devo. See Link to the cited article (accessed02/03/2026).
14. Experimental study of effect of infill density on tensile and flexural strength of 3D printed parts10.1186/s44147-023-00273-x ↗
15. Preliminary study on mechanical properties of 3D printed multi-materials ABS/PC parts: Effect of printing parameters10.21315/jps2021.32.2.7 ↗
16. Influence of infill percentage on mechanical properties of 3D printed thermoplastics