journal article·2019-02

Design Optimization of Hybrid FRP/RC Bridge

Vasileios S. Papapetrou, Ali Y. Tamijani, Jeff Brown, Daewon Kim

Applied Composite Materials· Volume 26· Issue 1
Publisher page

Abstract

The hybrid bridge consists of a Reinforced Concrete (RC) slab supported by U-shaped Fiber Reinforced Polymer (FRP) girders. Previous studies on similar hybrid bridges constructed in the United States and Europe seem to substantiate these hybrid designs for lightweight, high strength, and durable highway bridge construction. In the current study, computational and optimization analyses were carried out to investigate six composite material systems consisting of E-glass and carbon fibers. Optimization constraints are determined by stress, deflection and manufacturing requirements. Finite Element Analysis (FEA) and optimization software were utilized, and a framework was developed to run the complete analyses in an automated fashion. Prior to that, FEA validation of previous studies on similar U-shaped FRP girders that were constructed in Poland and Texas is presented. A finer optimization analysis is performed for the case of the Texas hybrid bridge. The optimization outcome of the hybrid FRP/RC bridge shows the appropriate composite material selection and cross-section geometry that satisfies all the applicable Limit States (LS) and, at the same time, results in the lightest design. Critical limit states show that shear stress criteria determine the optimum design for bridge spans less than 15.24 m and deflection criteria controls for longer spans. Increased side wall thickness can reduce maximum observed shear stresses, but leads to a high weight penalty. A taller cross-section and a thicker girder base can efficiently lower the observed deflections and normal stresses. Finally, substantial weight savings can be achieved by the optimization framework if base and side-wall thickness are treated as independent variables.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Structural Behavior of Reinforced Concrete · Concrete Corrosion and Durability · Structural Load-Bearing Analysis

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (19)

Show source-provided references
1. Bakis, C.E., Bank, L.C., Brown, V.L., et al.: Fiber-Reinforced Polymer Composites for Construction–State-of-the-Art Review. J. Comp. Constr. 6(2), 73–87 (2002)10.1061/(ASCE)1090-0268(2002)6:2(73) ↗
2. Bank L. C.: Structural design with FRP materials, Comp. Constr. (2006)
3. AASHTO: Guide Specifications for Design of FRP Pedestrian Bridges. 1st Edit., Washington, DC (2008)
4. AASHTO: LRFD Bridge Design Guide Specifications for GFRP-Reinforced Concrete Bridge Decks and Traffic Railings. 1st Edit., Washington, DC (2009)
5. AASHTO: LRFD Bridge Design Specifications., 7th Edit., Washington, DC (2014)
6. AASHTO: LRFD Guide Specifications for Design of Concrete-Filled FRP Tubes, Wanshigton, DC (2012)
7. O’Connor, J.S.: Composite Bridge Decking: Final Project Report, FHWA-HIF-13-029. Federal Highway Administration, Washington, D.C (2013)
8. Zhao, L., Burgueno, R., La Rovere, H., et al.: Preliminary Evaluation of the Hybrid Tube Bridge System, California Department of Transportation Report No. TR-2000/04 (2000)
9. Maine, Department of Transportation. Research Reports and Publications: Bridge Research, http://www.maine.gov/mdot/tr/rrp/ (2016) Accessed 21 November 2017
10. Chen, Y., Ziehl, P.H., Harrison, K.W. : Experimental Characterization and Optimization of Hybrid FRP/RC Bridge Superstructure System. J. Bridg. Eng. 14(1), 45–54 (2009)10.1061/(ASCE)1084-0702(2009)14:1(45) ↗
11. Ziehl, P.H., Engelhardt, M.D., Fowler, T.J., et al.: Design and Field Evaluation of Hybrid FRP/Reinforced Concrete Superstructure System. J. Bridg. Eng. 14(5), 309–318 (2009)10.1061/(ASCE)BE.1943-5592.0000002 ↗
12. Siwowski, T., Kaleta, D., Rajchel, M.: Design and research on the first polish FRP composite road bridge. Romanian J. Transp. Infrast. 4(2), 62–74 (2015)10.1515/rjti-2015-0037 ↗
13. Papapetrou, V.S., Tamijani, A.Y., Daewon, K.: Preliminary Wing Study of General Aviation Aircraft with Stitched Composite Panels. J. Aircr. 54(2), 704–715 (2017). https://doi.org/10.2514/1.C03388410.2514/1.C033884 ↗
14. Fernandes, R.R., Tamijani, A.Y.: Flutter Analysis of Laminated Curvilinear-Stiffened Plates. AIAA J. 55(3), 998–1011 (2017)10.2514/1.J055021 ↗
15. Aboelseoud, M.A., Myers, J.J.: Finite-Element Modeling of Hybrid Composite Beam Bridges in Missouri, J. Bridge Eng (2015)10.1061/(ASCE)BE.1943-5592.0000635 ↗
16. Harris, D.K., Civitillo, J.M., Gheitasi, A.: Performance and Behavior of Hybrid Composite Beam Bridge in Virginia: Live Load Testing. J. Bridg. Eng. 21(6), 1–1 (2016)10.1061/(ASCE)BE.1943-5592.0000820 ↗
17. VectorPly. Databease, http://vectorply.com/database-search/ Accessed 12 September 2016
18. WacoBoom. Material Specifications, http://wacoboom.com/booms/specifications/ (2016) Accessed 20 October 2016
19. Hexcel. Data Resources, http://www.hexcel.com/Resources/DataSheets/ (2016) Accessed 01 September 2016