journal article·2018-06

Resin Viscosity Influence on Fiber Compaction in Tapered Resin Injection Pultrusion Manufacturing

N. B. Masuram, J. A. Roux, A. L. Jeswani

Applied Composite Materials· Volume 25· Issue 3
Publisher page

Abstract

Viscosity of the liquid resin effects the chemical and mechanical properties of the pultruded composite. In resin injection pultrusion manufacturing the liquid resin is injected into a specially designed tapered injection chamber through the injection slots present on top and bottom of the chamber. The resin is injected at a pressure so as to completely wetout the fiber reinforcements inside the tapered injection chamber. As the resin penetrates through the fibers, the resin also pushes the fibers away from the wall towards the center of chamber causing compaction of the fiber reinforcements. The fibers are squeezed together due to compaction, making resin penetration more difficult; thus higher resin injection pressures are required to efficaciously penetrate through the compacted fibers and achieve complete wetout. The impact of resin viscosity on resin flow, fiber compaction, wetout and on the final product is further discussed. Injection chamber design predominantly effects the resin flow inside the chamber and the minimum injection pressure required to completely wet the fibers. Therefore, a desirable injection chamber design is such that wetout occurs at lower injection pressures and at low internal pressures inside the injection chamber.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Epoxy Resin Curing Processes · Injection Molding Process and Properties · Mechanical Behavior of Composites

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (18)

Show source-provided references
1. Jeswani, A.L., Roux, J.A.: Numerical Modeling of Design Parameters for Manufacturing Polyester/Glass Composites by Resin Injection Pultrusion. Polym. Polym. Compos. 14, 651–669 (2006)
2. Masuram, N.B., Roux, J.A., Jeswani, A.L.: Fiber Volume Fraction Effect on Fiber Reinforcement Compaction in a Tapered Resin Injection Pultrusion Manufacturing. J. Appl. Compos. Mater. 23(3), 421–442 (2016)10.1007/s10443-015-9466-z ↗
3. Shakya, N.S., Roux, J.A., Jeswani, A.L.: Effect of Resin Viscosity in Fiber Reinforcement Compaction in Resin Injection Pultrusion Process. J. Appl Compos. Mater. 20(6), 1173–1193 (2013)10.1007/s10443-013-9320-0 ↗
4. Ranjit, S., Roux, J.A., Jeswani, A.L.: Impact of Single and Multiple Injection Slot Locations for Attached-Die and Detached-Die Tapered Resin Injection Pultrusion. Polym. Polym. Compos. 22(6), 495–507 (2014)
5. Palikhel, D.R., Roux, J.A., Jeswani, A.L.: Die-Attached Versus Die Detached Resin Injection Chamber for Pultrusion. J. Appl. Compos. Mater. 20, 55–72 (2013)10.1007/s10443-012-9251-1 ↗
6. Ranga, B.K., Roux, J.A., Jeswani, A.L.: Effect of Chamber Length and Pull Speed of Tapered Resin Injection Pultrusion. J. Reinf. Plast. Compos. 30(10), 1373–1387 (2011)10.1177/0731684411422415 ↗
7. Mitlapalli, R., Roux, J.A., Jeswani, A.L.: Chamber Length and Injection Slot Location and Multiple Slots of Tapered Resin Injection Pultrusion. J. Porous Media. 14, 17–32 (2011)10.1615/JPorMedia.v14.i1.20 ↗
8. Srinivasagupta, D., Kardos, J.L.: Rigorous Dynamic Model-based Economic Design of the Injected Pultrusion Process with Controllability Considerations. J. Compos. Mater. 37, 1851–1888 (2003)10.1177/002199803036241 ↗
9. Batch, G.L., Cumiskey, S., Macosko, C.W.: Compaction of Fiber Reinforcements. J. Polym. Compos. 23(3), 307–318 (2002)10.1002/pc.10433 ↗
10. Ding, Z., Li, S., Yang, H., Lee, L.J.: Numerical and Experimental Analysis of Resin Flow and Cure in Resin Injection Pultrusion (RIP). J. Polym. Compos. 21(5), 762–778 (2000)10.1002/pc.10231 ↗
11. Kim, Y.R., McCarthy, S.P.: Compressibility and Relaxation of Fiber Reinforcements during Composite Processing. J. Polym. Compos. 12(1), 13–19 (1991)10.1002/pc.750120104 ↗
12. Kim, Y.R., McCarthy, S.P., Fanucci, J.P., Nolet, S.C., Koppernaes, C.: Resin Flow Through Fiber Reinforcement during Composite Processing. SAMPE Q. 22(3), 16–22 (1991)
13. Gutowski, T.G., Cai, Z., Boucher, D., Kingery, J., Wineman, S.: Consolidation Experiments for Laminate Composites. J. Compos. Mater. 21(7), 650–669 (1987)10.1177/002199838702100705 ↗
14. Gutowski, T.G., Morigaki, T., Cai, Z.: Consolidation Experiments for Laminate Composites. J. Compos. Mater. 21(2), 172–188 (1987)10.1177/002199838702100207 ↗
15. Gutowski, T.G., Cai, Z., Kingery, J., Wineman, S.J.: Resin Flow/ Fiber Deformation Experiments. SAMPE Q. 17(4), 54–58 (1986)
16. Darcy, H.: Les fontaines publique de la ville de Dijon. Dalmont, Paris (1856)
17. Patankar, S.: Numerical Heat and Fluid Flow. Hemisphere Publishing Corporation, New York (1980)
18. Carman, P.C.: Fluid Flow Through Granular Beds. Trans. Int. Chem. Eng. 15, 150–166 (1937)