Computational Analysis of Torsional Bulking Behavior of 3D 4-Directional Braided Composites Shafts
Source abstract
Abstract
The torsional bulking behavior of 3D 4-directional braided composites shafts was analyzed in this work. First, the unit cell models of 3D 4-directional braided composites shafts with different braiding angles and fiber volume fraction were built up. Then, the elastic parameters of 3D 4-directional braided composites shafts were predicted using the unit cells under different boundary conditions. Finally, the torsional bulking eigenvalues and bulking modes of the composites shafts were obtained by numerical simulation, and the effects of braiding angle and fiber volume fraction on the torsional bulking behavior of 3D 4-directional braided composites shafts were analyzed. The simulation results show that the bulking eigenvalues increase with the increase of braiding angle and fiber volume fraction. This work will play an important role in the design of 3D 4-directional braided composites shafts.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Mechanical Behavior of Composites · Metal Forming Simulation Techniques · Mechanical stress and fatigue analysis
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (29)
Show source-provided references
1. Pater, Z., Gontarz, A., Tomczak, J., Bulzak, T.: Producing hollow drive shafts by rotary compression. Arch Civ Mech Eng. 15, 917–924 (2015)10.1016/j.acme.2014.10.002 ↗
2. Gayen, D., Chakraborty, D., Tiwari, R.: Whirl frequencies and critical speeds of a rotor-bearing system with a cracked functionally graded shaft – Finite element analysis. European Journal of Mechanics - A/Solids. 61, 47–58 (2017)10.1016/j.euromechsol.2016.09.003 ↗
3. Hao, W., Ge, D., Ma, Y., Yao, X., Shi, Y.: Experimental investigation on deformation and strength of carbon/epoxy laminated curved beams. Polym. Test. 31, 520–526 (2012)10.1016/j.polymertesting.2012.02.003 ↗
4. Hao, W., Yuan, Y., Zhu, J., Chen, L.: Effect of impact damage on the curved beam interlaminar strength of carbon/epoxy laminates. J. Adhes. Sci. Technol. 30, 1189–1200 (2016)10.1080/01694243.2016.1144261 ↗
5. Karihaloo, B.L., Xiao, Q.Z., Wu, C.C.: Homogenization-based multivariable element method for pure torsion of composite shafts. Comput. Struct. 79, 1645–1660 (2001)10.1016/S0045-7949(01)00091-8 ↗
6. Shokrieh, M.M., Hasani, A., Lessard, L.B.: Shear buckling of a composite drive shaft under torsion. Compos. Struct. 64, 63–69 (2004)10.1016/S0263-8223(03)00214-9 ↗
7. Mutasher, S.A.: Prediction of the torsional strength of the hybrid aluminum/composite drive shaft. Mater Design. 30, 215–220 (2009)10.1016/j.matdes.2008.05.024 ↗
8. Sevkat, E., Tumer, H.: Residual torsional properties of composite shafts subjected to impact loadings. Mater Design. 51, 956–967 (2013)10.1016/j.matdes.2013.05.004 ↗
9. Sevkat, E., Tumer, H., Halidun Kelestemur, M., Dogan, S.: Effect of torsional strain-rate and lay-up sequences on the performance of hybrid composite shafts. Mater Design. 60, 310–319 (2014)10.1016/j.matdes.2014.03.069 ↗
10. Misri, S., Sapuan, S.M., Leman, Z., Ishak, M.R.: Torsional behaviour of filament wound kenaf yarn fibre reinforced unsaturated polyester composite hollow shafts. Mater Design. 65, 953–960 (2015)10.1016/j.matdes.2014.09.073 ↗
11. Chang, C., Chang, M., Huang, J.H.: Vibration analysis of rotating composite shafts containing randomly oriented reinforcements. Compos. Struct. 63, 21–32 (2004)10.1016/S0263-8223(03)00121-1 ↗
12. Na, S., Yoon, H., Librescu, L.: Effect of taper ratio on vibration and stability of a composite thin-walled spinning shaft. Thin Wall Struct. 44, 362–371 (2006)10.1016/j.tws.2006.02.007 ↗
13. Qatu, M.S., Iqbal, J.: Transverse vibration of a two-segment cross-ply composite shafts with a lumped mass. Compos. Struct. 92, 1126–1131 (2010)10.1016/j.compstruct.2009.10.007 ↗
14. Khalid, Y.A., Mutasher, S.A., Sahari, B.B., Hamouda, A.M.S.: Bending fatigue behavior of hybrid aluminum/composite drive shafts. Mater Design. 28, 329–334 (2007)10.1016/j.matdes.2005.05.021 ↗
15. Islam, M.S., Tong, L.: Effects of initial blister radius and shaft diameter on energy release rate of metal–polymer composite coating. Int. J. Adhes. Adhes. 62, 107–123 (2015)10.1016/j.ijadhadh.2015.07.007 ↗
16. Kim, H.S., Kim, B.C., Lim, T.S., Lee, D.G.: Foreign objects impact damage characteristics of aluminum/composite hybrid drive shaft. Compos. Struct. 66, 377–389 (2004)10.1016/j.compstruct.2004.04.059 ↗
17. Li, D., Fang, D., Jiang, N., Xuefeng, Y.: Finite element modeling of mechanical properties of 3D five-directional rectangular braided composites. Compos. Part B. 42, 1373–1385 (2011)10.1016/j.compositesb.2011.05.042 ↗
18. Drach, A., Drach, B., Tsukrov, I.: Processing of fiber architecture data for finite element modeling of 3D woven composites. Adv. Eng. Softw. 72, 18–27 (2014)10.1016/j.advengsoft.2013.06.006 ↗
19. Ayranci, C., Carey, J.P.: Predicting the longitudinal elastic modulus of braided tubular composites using a curved unit-cell geometry. Compos. Part B. 41, 229–235 (2010)10.1016/j.compositesb.2009.10.006 ↗
20. Yu, X.G., Cui, J.Z.: The prediction on mechanical properties of 4-step braided composites via two-scale method. Compos. Sci. Technol. 67, 471–480 (2007)10.1016/j.compscitech.2006.08.028 ↗
21. McGregor, C., Vaziri, R., Xiao, X.: Finite element modelling of the progressive crushing of braided composite tubes under axial impact. Int J Impact Eng. 37, 662–672 (2010)10.1016/j.ijimpeng.2009.09.005 ↗
22. Xiao, X., McGregor, C., Vaziri, R., Poursartip, A.: Progress in braided composite tube crush simulation. Int J Impact Eng. 36, 711–719 (2009)10.1016/j.ijimpeng.2008.09.006 ↗
23. Xiao, X., Botkin, M.E., Johnson, N.L.: Axial crush simulation of braided carbon tubes using MAT58 in LS-DYNA. Thin Wall Struct. 47, 740–749 (2009)10.1016/j.tws.2008.12.004 ↗
24. Zhang, P., Gui, L., Fan, Z., Yu, Q., Li, Z.: Finite element modeling of the quasi-static axial crushing of braided composite tubes. Comput. Mater. Sci. 73, 146–153 (2013)10.1016/j.commatsci.2013.01.026 ↗
25. Zaman, W., Li, K., Ikram, S., Li, W., Zhang, D., Guo, L.: Morphology, thermal response and anti-ablation performance of 3D-four directional pitch-based carbon/carbon composites. Corros. Sci. 61, 134–142 (2012)10.1016/j.corsci.2012.04.036 ↗
26. Hao, W., Yuan, Y., Yao, X., Ma, Y.: Computational analysis of fatigue behavior of 3D 4-directional braided composites based on unit cell approach. Adv. Eng. Softw. 82, 38–52 (2015)10.1016/j.advengsoft.2014.12.007 ↗
27. Chen, L., Yao, X., Cen, S.: Predictions of elastic property on 2.5D C/SiC composites based on numerical modeling and semi-analytical method. Compos. Part B. 74, 53–65 (2015)10.1016/j.compositesb.2015.01.009 ↗
28. Li, S.: Boundary conditions for unit cells from periodic microstructures and their implications. Compos. Sci. Technol. 68, 1962–1974 (2008)10.1016/j.compscitech.2007.03.035 ↗
29. Sun, C.T., Vaidya, R.S.: Prediction of composite properties from a representative volume element. Compos. Sci. Technol. 56, 171–179 (1996)10.1016/0266-3538(95)00141-7 ↗