Influence of Compression and Shear on the Strength of Composite Laminates with Z-Pinned Reinforcement
Source abstract
Abstract
The influence of compression and shear loads on the strength of composite laminates with z-pins is evaluated parametrically using a 2D Finite Element Code (FLASH) based on Cosserat couple stress theory. Meshes were generated for three unique combinations of z-pin diameter and density. A laminated plate theory analysis was performed on several layups to determine the bi-axial stresses in the zero degree plies. These stresses, in turn, were used to determine the magnitude of the relative load steps prescribed in the FLASH analyses. Results indicated that increasing pin density was more detrimental to in-plane compression strength than increasing pin diameter. Compression strengths of lamina without z-pins agreed well with a closed form expression derived by Budiansky and Fleck. FLASH results for lamina with z-pins were consistent with the closed form results, and FLASH results without z-pins, if the initial fiber waviness due to z-pin insertion was added to the fiber waviness in the material to yield a total misalignment. Addition of 10% shear to the compression loading significantly reduced the lamina strength compared to pure compression loading. Addition of 50% shear to the compression indicated shear yielding rather than kink band formation as the likely failure mode. Two different stiffener reinforced skin configurations with z-pins, one quasi-isotropic and one orthotropic, were also analyzed. Six unique loading cases ranging from pure compression to compression plus 50% shear were analyzed assuming material fiber waviness misalignment angles of 0, 1, and 2 degrees. Compression strength decreased with increased shear loading for both configurations, with the quasi-isotropic configuration yielding lower strengths than the orthotropic configuration.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Mechanical Behavior of Composites · Composite Structure Analysis and Optimization · Structural Load-Bearing Analysis
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (12)
Show source-provided references
1. O’Brien, T. K., ‘Fracture Mechanics of Composite Delamination,’ ASM Handbook, Vol. 21, Composites, August, 2001, p. 241–245.10.31399/asm.hb.v21.a0003380 ↗
2. Clarke, A., Greenhalgh, E., Meeks, C. and Jones, C., Enhanced Structural Damage Tolerance of CFRP Primary Structures by Z-pin Reinforcement, 44th AIAA SDM Conference, paper AIAA-2003-1679, Norfolk, Virginia, 2003.10.2514/6.2003-1679 ↗
3. Freitas, G., Fusco, T. and Campbell, T., ‘Z-fiber Technology and Products for Enhancing Composite Design,’ in AGARD Conference Proceedings 590: Bolted/Bonded Joints in Polymeric Composites, Advisory Group for Aerospace Research and Development, 1997, pp. 8–17.
4. Steeves, C. A. and Fleck, N. A., ‘In-plane properties of composite laminates with through-thickness pin reinforcement’, International Journal of Solids and Structure, 43, 2006, 3197–3212.10.1016/j.ijsolstr.2005.05.017 ↗
5. Sun, C. T., Novel Methods for Testing and Modelling Composite Materials and Laminates, in Proceedings of the Second International Conference on Composites Testing and Model Identification, CompTest 2004, Bristol, England, September, 2004.
6. Sun, C. T. and Jun, A. W., ‘Compressive strength of unidirectional composites with matrix non-linearity’, Composites Science and Technology, 52(2), 577–587.10.1016/0266-3538(94)90041-8 ↗
7. Fleck, N. A. and Shu, J. Y., ‘Microbuckle Initiation in Fibre Composites: A Finite element study’, Journal of the Mechanics and Physics of Solids, 43(2), 1995, 1887–1918.10.1016/0022-5096(95)00057-P ↗
8. Shu, J. Y. and Fleck, N. A., User’s Manual for Finite Element Code for Fibre Microbuckling, Cambridge University Engineering Department C-MATS Technical Report 224 (ISSN 0309-6505), May, 1995.
9. Liu, D. and Fleck, N. A., User’s Manual II for Finite Element Code FLASH for Fibre Microbuckling, Cambridge University Engineering Department C-MICROMECH Technical Report 29 (ISSN 0309-7420), November, 1999.
10. O’Brien, T. K., and Krueger, R., Influence of Compression and Shear on the Strength of Composite Laminates with z-pinned Reinforcement, NASA TM-2005-213768, ARL TR 3524, June 2005.
11. Krueger, R., Modelling of Unit-cells with Z-pins Using FLASH: Pre-processing and Post-processing, NIA Report No. 2005-01, NASA/CR-2005-213905, 2005.
12. Budiansky, B. and Fleck, N. A., ‘Compressive Failure of Fibre Composites’, Journal of the Mechanics and Physics of Solids, 41(1), 1993, 183–211.10.1016/0022-5096(93)90068-Q ↗