journal article·2011-08

A Proposed Approach for Certification of Bonded Composite Repairs to Flight-Critical Airframe Structure

Alan A. Baker

Applied Composite Materials· Volume 18· Issue 4
Publisher page

Abstract

This paper focuses on the difficult issue of the certification of adhesively bonded repairs in applications where credit has to be given to the patch for restoring residual strength in flight-critical structure. The scope of the paper includes both adhesively bonded composite repairs to composite components and composite repairs to metallic components. After discussing typical bonded repairs and, as a baseline, procedures currently used to certify new structure, a proposal is made which may constitute an acceptable basis for the structural certification of repairs. The key requirement is to demonstrate an acceptably low probability of patch disbonding during the remaining life of the structure. The focus is on one-off repairs where development of a comprehensive certification procedure based even on limited testing will be infeasible:
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Mechanical Behavior of Composites · Probabilistic and Robust Engineering Design · Fatigue and fracture mechanics

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (30)

Show source-provided references
1. Baker, A.A., Rose, L.F.J, Jones, R. (eds.): “Advances in the Bonded Composite Repair of Metallic Aircraft Structure”. Elsevier (2002).
2. Baker A.A.: ‘Repair Techniques for Composite Structures’ Chapter 13. In: Middleton, D.H. (ed.) Composite Materials in Aircraft Structure. Longman Scientific and Technical Publishers (1990).
3. Hart-Smith L.J.: Analysis and Design of Advanced Composite Bonded Joints. NASA CR-2218 (1974).
4. Baker A.A.: “Development of a Hard-Patch Approach for Scarf Repairs of Composite Structure”. Defence Science and Technology Organisation Paper T-R-1892. (2006)
5. Rider, A.N., Chun, C.H., Chang, P.: Bonded Composite Repairs for a Carbon/BMI Composite Operating at Elevated Temperature. Compos A 41, 902–912 (2010)10.1016/j.compositesa.2010.03.006 ↗
6. Hoskin, B.C, Baker, A.A., Dutton, S., Bond, D., Callus, P.: “Airworthiness Considerations for Aircraft Structure.” In: Baker, A.A, Dutton, S., Kelly D. (eds.) “Composite Materials for Aircraft Structure” American Institute of Aeronautics and Astronautics, pp. 477–489, (2004).
7. Baker, A.A, Kelly, D.: “Joining of Composite Structures.” In: Baker, A.A, Dutton, S., Kelly, D. (eds.) “Composite Materials for Aircraft Structure” American Institute of Aeronautics and Astronautics, pp. 289–366, (2004).
8. Torkington, C.: “The Regulatory Aspects of the Repair of Civil Aircraft Metal Structures.” International Conference on Aircraft Damage Assessment and Repair: 1991; Preprints of Papers. p. 1–5. Barton, ACT: Institution of Engineers, Australia (1991).
9. Baker, A.A.: “Certification issues for Critical Repairs” In: Baker, A.A., Rose, L.F.J, Jones, R. (eds.) “Advances in the Bonded Composite Repair of Metallic Aircraft Structure”, pp. 615–639. Elsevier (2002).
10. Baker, A.A.: “Boron/Epoxy Patching Efficiency Studies”. In: Baker, A.A., Rose, L.F.J, Jones. R. (eds.) “Advances in the Bonded Composite Repair of Metallic Aircraft Structure”, pp, 375–397. Elsevier (2002).
11. Hall, S.R., Raizenne, M.D., Simpson, D.L.: A Proposed Composite Repair Methodology for Primary Structure. Composites 25, 479–483 (1989)10.1016/0010-4361(89)90218-8 ↗
12. Wang, C.H., Gunnion, A.J.: On the Design Methodology of Scarf Repairs to Composite Laminates. Compos Sci Technol 68, 35–46 (2008)10.1016/j.compscitech.2007.05.045 ↗
13. Baker, A.A., Chester, R.J., Hugo, G.R., Radtke, T.C.: Scarf Repairs to Highly Strained Carbon/Epoxy Structure. Int J Adhesion 19, 16–171 (1999)
14. Hart-Smith, L.J.: Stress Analysis: A Continuum Mechanics Approach’. In: Kinloch (ed.) Developments in Adhesives 2. Applied Science Publishers, UK (1981)
15. Kieger, R.B.: ‘Stress Analysis Concepts for Adhesive Bonding of Aircraft Primary Structure,’ In: Johnston, W.S. (ed.) “Adhesively Bonded Joints”:Testing Analysis, and Design, ASTM STP 981, (1988).
16. Davis, M.J., Janardhana, M., MacKenzie, A.: “ A Rigorous Approach to the Certification of Adhesive Bonded Repairs.” “FAA Workshop on Certification of Adhesive Bonded Structures and Repairs”. Seattle, USA (2004).
17. Chalkley, P.D., Wang, C.H, Baker, A.A.: “Fatigue Testing of Generic Bonded Joints”. In: Baker, A.A., Rose, L.F.J, Jones, R. (eds) “Advances in the Bonded Composite Repair of Metallic Aircraft Structure”, pp. 643–656. Elsevier (2002).
18. Rose L.R.F.: “Theoretical Analysis of Crack Patching”, Chapter 5. In: Baker, A.A, Jones R. (eds.) Bonded Repair of Aircraft Structures, pp. 107–173. Martinus Nijhoff (1988).
19. Wang, J., Rider, A.N., Heller, M., Kaye, R.: Theoretical and Experimental Research into Optimal Edge Taper for Bonded Repair Patches Subject to Fatigue Loading. Int J Adhes Adhes 25, 410–426 (2005)10.1016/j.ijadhadh.2004.11.007 ↗
20. Alderson, R.C.: Damage Tolerance of Bonded Aircraft Structures. Int J Fatigue 31, 1624–1030 (2008)
21. Walker, K., Rose, L.R.F.: “Case History: F111 Lower Wing Skin Repair Substantiation ”. In: Baker, A.A., Rose, L.F.J, Jones, R. (eds) “Advances in the Bonded Composite Repair of Metallic Aircraft Structure”, pp. 797–811. Elsevier (2002).
22. Fredell, R.S.: “Damage Tolerant Repair Techniques for Pressurised Aircraft Fuselages” PhD-Thesis Delft University (1994).
23. Vlot, A., Verboeven, S., Woerden, S., Giujt, C.B., Greer, J.M.: “Bonded Metal Laminate Repair Patches”. Proceddings of the 20th Symposium of the International Conference on Aeronautical Fatigue, pp 331–357. Washington USA, (1999).
24. Olsson-Jacques, C.L., Arnott, D.R., Lambrianidis, L.T., Wilson, A.R., Kindermann, M.R., Theodossiou, G.: "Toward Quality Monitoring of Adherend Surfaces Prior to Adhesive Bonding in Aircraft Repairs". The Proceedings of The International Aerospace Congress 1997 seventh Australian Aeronautical Conference, Institution of Engineers Australia, 24–27 February 1997 Sydney Australia p. 511–520.
25. Arnot, D., Rider, A., Mazza, J.: “Surface Treatment and Repair Bonding”. In: Baker, A.A., Rose, L.F.J., Jones, R. (eds.) “Advances in the Bonded Composite Repair of Metallic Aircraft Structure”, pp. 643–656. Elsevier (2002).
26. Rider, A.: “Prebond Inspection Techniques to Improve the Quality of Adhesive Bonding Surface Treatments”. DSTO-TR-1919 (2006).
27. Royal Australian Air Force Engineering Standard C5033, Composite Materials and Adhesive Bonded Repairs, September 1995, RAAF Headquarters Logistics Command, Melbourne, Vic., Australia
28. Davis M.: “Practical Implementation Technology for Adhesive Bonded Repairs”. In: Baker, A.A., Rose, L.F.J., Jones, R., (eds.) “Advances in the Bonded Composite Repair of Metallic Aircraft Structure”, pp. 727–757. Elsevier (2002).
29. Bittern, D., Baker, A.A., Wang, J.: "Development of a Proof Test for Through-Life Monitoring of Adhesive Bond Integrity". CRCACS TM 10079 (2010)
30. Baker, A.A., Rajic, N., Davis, C.: Towards a Practical Health Monitoring System for Patched Cracks in Aircraft Structure. Compos A 40A, 1340–1352 (2009)10.1016/j.compositesa.2008.09.015 ↗