Machining of circular micro holes by electrochemical micro-machining process
Source abstract
Abstract
Machining of micro holes with micro electro- chemical machining (micro ECM) process has been carried out with an indigenously developed set up. This paper describes relevant problems and solutions for the circular micro holes machining process on 304 stainless steel sheets with 60 lm thickness using high speed steel cylindrical tool of diameter 500 lm and using dilute H2SO4 as elec- trolyte. The taper angle variation of the machined hole is analyzed and reported for different experimental setting parameters. The minimum value of the taper angle of machined holes is achieved at the parameter setting of 0.4 mol/L H2SO4, 700 kHz, 600 ns and 21 V, for stainless steel sheets and HSS tool.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advanced Machining and Optimization Techniques · Advanced Surface Polishing Techniques · Advanced machining processes and optimization
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (18)
Show source-provided references
1. Bhattacharyya B, Munda J, Malapati M (2004) Advancement in electrochemical micro-machining. Int J Mach Tools Manuf 44(15):1577–158910.1016/j.ijmachtools.2004.06.006 ↗
2. Masuzawa T (2000) State of the art of micromachining. Ann CIRP 49(2):473–48810.1016/S0007-8506(07)63451-9 ↗
3. Bhattacharyya B, Munda J (2003) Experimental investigation into electrochemical micromachining (EMM) process. J Mater Process Technol 140:287–29110.1016/S0924-0136(03)00722-2 ↗
4. Bhattacharyya B, Malapati M, Munda J (2005) Experimental study on electrochemical micromachining. J Mater Process Technol 169(3):485–49210.1016/j.jmatprotec.2005.04.074 ↗
5. Bhattacharyya B, Malapati M, Munda J et al (2007) Influence of tool vibration on machining performance in electrochemical micro-machining of copper. Int J Mach Tools Manuf 47(2):335–34210.1016/j.ijmachtools.2006.03.005 ↗
6. Zhang Z, Zhu D, Qu N, Wang M (2007) Theoretical and experimental investigation on electrochemical micromachining. Microsyst Technol 13:607–61210.1007/s00542-006-0369-7 ↗
7. Kim BH, Na CW, Lee YS et al (2005) Micro electrochemical machining of 3D micro structure using dilute sulpfuric acid. Ann CIRP 54(1):191–19410.1016/S0007-8506(07)60081-X ↗
8. Kim BH, Park BJ, Chu CN (2006) Fabrication of multiple electrodes by reverse EDM and their application in micro ECM. J Micromech Microeng 16:84310.1088/0960-1317/16/4/022 ↗
9. Ahn SH, Ryu SH, Choi DK et al (2004) Electro-chemical micro drilling using ultra short pulses. Precis Eng 28:129–13410.1016/j.precisioneng.2003.07.004 ↗
10. Cagnon L, Kirchner V, Kock M et al (2003) Electrochemical micromachining of stainless steel by ultra short voltage pulses. Z Phys Chem 217:299–31310.1524/zpch.217.4.299.20383 ↗
11. Munda J, Malapati M, Bhattacharyya B (2007) Control of micro-spark and stray-current effect during EMM process. J Mater Process Technol 194(1–3):151–15810.1016/j.jmatprotec.2007.04.112 ↗
12. Sen M, Shan HS (2005) A review of electrochemical macro- to micro-hole drilling processes. Int J Mach Tools Manuf 45(2):137–15210.1016/j.ijmachtools.2004.08.005 ↗
13. Li Y, Zheng Y, Yang G, Peng L (2003) Localized electrochemical micromachining with gap control. Sens Actuators A 108(1–3):144–148
14. Jahan MP, Wong YS, Rahman M (2009) A study on the quality micro-hole machining of tungsten carbide by micro-EDM process using transistor and RC-type pulse generator. J Mater Process Technol 209(4):1706–171610.1016/j.jmatprotec.2008.04.029 ↗
15. Lim HS, Wong YS, Rahman M et al (2003) A study on the machining of high-aspect ratio micro-structures using micro-EDM. J Mater Process Technol 140(1–3):318–32510.1016/S0924-0136(03)00760-X ↗
16. Asad ABMA, Masaki T, Rahman M et al (2007) Tool-based micro-machining. J Mater Process Technol 192–193:204–21110.1016/j.jmatprotec.2007.04.038 ↗
17. Rahman AA, Mamat A, Wagiman A (2009) Effect of machining parameters on hole quality of micro drilling for brass. Mod Appl Sci 3(5):221–23010.5539/mas.v3n5p221 ↗
18. Schuster R, Kirchner V, Allongue P et al (2000) Electrochemical micromachining. Science 289(5476):98–10110.1126/science.289.5476.98 ↗