journal article·2020Open access

Statistical Process Control and Related Methods for Improvement of the Treated-Wood Industries

Timothy M. Young, Patricia K. Lebow, Stan Lebow, Adam Taylor

Forest Products Journal· Volume 70· Issue 2

Abstract

Abstract An approach for implementing statistical process control and other statistical methods as a cost-savings measure in the treated-wood industries is outlined. The purpose of the study is to use industry data to improve understanding of the application of continuous improvement methods. Variation in wood treatment is a cost when higher-than-necessary chemical retention targets are required to meet specifications. The data for this study were obtained in confidence from the American Lumber Standard Committee and were paired, normalized assay retentions for charges inspected by both the treating facility and auditing agencies. Capability analyses were developed from this data for three use categories established by the American Wood Protection Association (AWPA), including UC3B (above ground, exterior), UC4A (ground contact, freshwater, general use), and UC4B (ground contact, freshwater, critical structures, or high decay hazard zones). Agency and industry data indicate that between 4.45 and 9.82 percent of the charges were below the lower confidence limit of the passing standard (LCLAWPA), depending on use category. A Taguchi loss function (TLF), which is quadratic based and decomposes the monetary loss into shift and variation components, was developed to estimate the additional cost due to process variation. For example, if a treatment input cost of $1.00/ft3 is assumed for UC3B, reducing the variation in total retention allows lowering treatment targets, e.g., 1.45 to 1.38, reducing costs to $0.76/ft3. The study provides some important continuous improvement tools for this industry such as control charts, Cpk, Cpm capability indices, and the one-sided TLF.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Advanced Statistical Process Monitoring · Manufacturing Process and Optimization · Quality and Management Systems

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (33)

Show source-provided references
1. Akaike, H. 1974. A new look at the statistical model identification. IEEE Trans. Automat. Contr. 19(6):716–723.
2. Al-Shomrani, A., A. I. Shawky, O. H. Arif, and M. Aslam. 2016. Log-logistic distribution for survival data analysis using MCMC. SpringerPlus5:1774.
3. American Wood Protection Association (AWPA). 2019. M22-19. Standard for third-party agency evaluation of inspection data. In:Book of Standards. American Wood Protection Association, Birmingham, Alabama. 4 pp.http://www.awpa.com/; http://www.alsc.org.
4. Anderson, D. R. 2008. Model Based Inference in the Life Sciences: A Primer on Evidence. Springer, New York. 184pp.
5. Boyles, R. 1991. The Taguchi capability index. J. Qual. Technol. 23(1):17–26.
6. Brown, T. D. 1982. Quality Control in Lumber Manufacturing. Miller Freeman Publications, San Francisco. 288pp.
7. Crowder, M. J., A. C. Kimber, R. L. Smith, and T. J. Sweeting. 1991. Statistical Analysis of Reliability Data. Chapman & Hall, London. 250pp.
8. Deming, W. E. 1975. On probability as a basis for action. Am. Stat. 29:146–152.
9. Findley, D. F. 1991. Counterexamples to parsimony and BIC. Ann. I. Stat. Math. 43:505–514.
10. Hahn, G. J. 1995. Deming's impact on industrial statistics: Some reflections. Am. Stat. 49(4):336–341.
11. Harry, M. and R. Schroeder. 2000. Six Sigma: The Breakthrough Management Strategy Revolutionizing the World's Top Corporations. Doubleday Random House, New York. 300pp.
12. JMP, version 14, 1989–2019. SAS Institute Inc., Cary, North Carolina. https://www.jmp.com/en_us/home.html. Accessed February 4,2020.
13. Lawless, J. F., R. J. Mackay, and J. A. Robinson. 1999. Analysis of variation transmission in manufacturing processes—Part I. J. Qual. Technol. 31(2):131–142.
14. Maness T. C., R. A. Kozak, and C. Staudhammer. 2003. Applying real-time statistical process control to manufacturing processes exhibiting between and within part size variability in the wood products industry. Qual. Eng. 16(1):113–125.
15. Maness, T. C., C. Staudhammer, and R. A. Kozak. 2002. Statistical considerations for real-time size control systems in wood products manufacturing. Wood Fiber Sci. 34(3):476–484.
16. Metzner, C., M. Platzer, T. M. Young, B. Bichescu, M. C. Barbu, and T. G. Rials. 2019. Accurately estimating and minimizing costs for the cellulosic biomass supply chain with statistical process control and the Taguchi Loss Function. BioResources14(2):2961–2976.
17. Montgomery, D. C. 2012. Introduction to Statistical Quality Control. 7th ed. John Wiley & Sons, Hoboken, New Jersey. 768pp.
18. Nutek Inc. 2014. Quality loss function and tolerance design—A method to quantify savings from improved product and process designs. Nutek, Bloomfield Hills, Michigan. 37pp.
19. Ohno, T. 1988. Toyota Production System: Beyond Large-Scale Production. Productivity Press, New York. 176pp.
20. Shewhart, W. A. 1931. Economic Control of Quality of Manufactured Product. D. Van Nostrand, New York. 501pp.
21. Stoumbos, Z. G., M. R. Reynolds, Jr., T. P. Ryan, and W. H. Woodall. 2000. The state of statistical process control as we proceed into the 21st century. J. Am. Stat. Assoc. 95:992–998.
22. Taguchi, G. 1993. Taguchi on Robust Technology Development. American Society of Mechanical Engineers (ASME) Press, New York. 136pp.
23. Taguchi, G., S. Chowdhury, Y. Wu, S. Taguchi, and H. Yano. 2005. Taguchi's Quality Engineering Handbook. John Wiley & Sons, Hoboken, New Jersey. 662pp.
24. Vlosky, R. P. 2009. Statistical Overview of the US Wood Preserving Industry: 2007. Southern Forest Products Association, Kenner, Louisiana. 34pp.
25. Woodall, W. H. 2000. Controversies and contradictions in statistical process control. J. Qual. Technol. 32(4):341–350.
26. Young, T., N. André, and J. Otjen. 2015. Quantifying the natural variation of formaldehyde emissions for wood composite panels. Forest Prod. J. 65(3/4):S82–S84.
27. Young, T. M. 2008. Reducing variation, the role of statistical process control in advancing product quality. Eng. Wood J. 11(2):41–42.
28. Young, T. M. 2012. Variation reduction—Avoiding the process improvement paradox. Eng. Wood J. 15(1):28–29.
29. Young, T. M., B. H. Bond, and J. Wiedenbeck. 2007. Implementation of a real-time statistical process control system in hardwood sawmills. Forest Prod. J. 57(9):54–62.
30. Young, T. M., P. K. Lebow, and S. Lebow. 2017. Statistical process control for residential treated wood. In:Proceedings of the American Wood Protection Association (AWPA) Conference 2017, April 9–12, Las Vegas, Nevada; AWPA, Birmingham, Alabama. Vol. 113,pp. 234–244.
31. Young, T. M., P. K. Lebow, S. Lebow, and A. Taylor. 2019. SPC Handbook for the Treated Wood Industries. The University of Tennessee, Institute of Agriculture, AgResearch, Knoxville. 71 pp.www.spc4lean.com. Accessed February 6, 2020.
32. Young, T. M. and P. M. Winistorfer. 1999. Statistical process control and the forest products industry. Forest Prod. J. 49(3):10–17.
33. Zeng, Y., T. M. Young, D. J. Edwards, F. M. Guess, and C.-H. Chen. 2016. Case studies: A study of missing data imputation in predictive modeling of a wood composite manufacturing process. J. Qual. Technol. 48(3):284–296.