journal article·2023-09Open access

Performance of Normal Strength Concrete Slab Strengthened with High-Performance Concrete After Exposure to Elevated Temperature

Mariam F. Ghazy, Metwally A. Abd Elaty, Nagat M. Zalhaf

Fire Technology· Volume 59· Issue 5

Abstract

Abstract Reinforced concrete as the most important construction material suffers from long-term deterioration due to different exposure conditions. Fire attack is a critical exposure condition as it can lead to complete collapse of the structure. On the other hand, the repair and strengthening of existing structures have become necessary both technically and financially. Moreover, since high-performance concretes (HPCs) are extensively used as repairing or strengthening materials for different structures, their performance after exposure to elevated temperature needs to be investigated. Therefore, this study is directed to investigate the post-fire flexural behavior of RC slabs cast with traditional normal strength concrete (NSC) and strengthened with HPC. Twenty-one RC slabs were prepared and tested including casting the full thickness with the same mixture (single-concrete slabs) and composite slabs (cast with NSC and HPC). Different variables were considered; using high strength concrete, 30% fly ash, 30% slag, 0.5% polypropylene, 0.5% steel fibers, hybrid fibers (0.5% steel + 0.5% polypropylene), reinforcement ratio, the side exposed to elevated temperature (tension or compression), and joining the HPC layer to the NSC (shear studs or epoxy resin). The slabs were exposed to the required temperature of 600°C for 2 h. The results show that strengthening the RC slab in tension or compression by using HPC remarkably enhanced the slab’s performance after exposure to elevated temperature. Specially, composite slabs containing hybrid fibers in tension side when exposed to elevated temperature from the tension side recorded the highest cracking load, ultimate load, stiffness, toughness, and ductility index as compared to the NSC slab, with increases of 92.8%, 116%, 157%, 335%, and 86.9%, respectively.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Fire effects on concrete materials · Structural Behavior of Reinforced Concrete · Structural Response to Dynamic Loads

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (74)

Show source-provided references
1. Mindeguia J-C, Pimienta P, Noumowé A, Kanema M (2010) Temperature, pore pressure and mass variation of concrete subjected to high temperature—experimental and numerical discussion on spalling risk. Cem Concr. Res 40(3):477–487. https://doi.org/10.1016/j.cemconres.2009.10.01110.1016/j.cemconres.2009.10.011 ↗
2. Eurocode 2 (2004) Design of concrete structures, part 1–2: general rules-structural fire design ENV 1992-1-2/UK: CEN. European Committee for Standardization, Brussels
3. Kodur VK, Dwaikat MB (2008) Effect of fire induced spalling on the response of reinforced concrete beams. Int J Concr Struct Mater 2(2):71–81. https://doi.org/10.4334/IJCSM.2008.2.2.07110.4334/IJCSM.2008.2.2.071 ↗
4. Kodur V, Yu B, Dwaikat M (2013) A simplified approach for predicting temperature in reinforced concrete members exposed to standard fire. Fire Saf J 51(56):39. https://doi.org/10.1016/j.firesaf.2012.12.00410.1016/j.firesaf.2012.12.004 ↗
5. Khaliq W, Kodur V (2011) Thermal and mechanical properties of fiber reinforced high performance self-consolidating concrete at elevated temperatures. Cem Concr Res 41:1112–1122. https://doi.org/10.1016/j.cemconres.2011.06.01210.1016/j.cemconres.2011.06.012 ↗
6. Nguyen T, Thai H, Ngo T (2023) Effect of steel fibers on the performance of an economical ultra-high strength concrete. Struct Concr 24:1–1510.1002/suco.202200326 ↗
7. Conforti A, Trabucchi I, Tiberti G et al (2019) Precast tunnel segments for metro tunnel lining: a hybrid reinforcement solution using macro-synthetic fibers. Eng Struct 199:109628. https://doi.org/10.1016/j.engstruct.2019.10962810.1016/j.engstruct.2019.109628 ↗
8. Khalighi A, Izadifard RA, Zarifian A (2020) Role of macro fibers (steel and hybrid-synthetic) in the residual response of RC beams exposed to high temperatures. SN Appl Sci 2:1981. https://doi.org/10.1007/s42452-020-03790-z10.1007/s42452-020-03790-z ↗
9. Martinola G, Meda A, Plizzari G et al (2010) Strengthening and repair of RC beams with fiber reinforced concrete. J Cem Concr Compos 32:731–739. https://doi.org/10.1016/j.cemconcomp.2010.07.00110.1016/j.cemconcomp.2010.07.001 ↗
10. Haddad RH, Al-Mekhlafy N, Ashteyat AM (2011) Repair of heat-damaged reinforced concrete slabs using fibrous composite materials. J Constr Build Mater 25:1213–1221. https://doi.org/10.1016/j.conbuildmat.2010.09.03310.1016/j.conbuildmat.2010.09.033 ↗
11. Naghibdehi MG, Sharbatdar MK, Mastali M (2014) Repairing reinforced concrete slabs using composite layers. Mater Des 58:136–144. https://doi.org/10.1016/j.matdes.2014.02.01510.1016/j.matdes.2014.02.015 ↗
12. Basha A, Fayed S, Mansour W (2020) Flexural strengthening of RC one way solid slab with strain hardening cementitious composites (SHCC). Adv Concr Constr 9(5):511–527. https://doi.org/10.12989/acc.2020.9.5.51110.12989/acc.2020.9.5.511 ↗
13. Xiao J-ZH, Li J, Jiang F (2004) Research on the seismic behavior of HPC shear walls after fire. Mater Struct 37:506–51210.1007/BF02481574 ↗
14. Dwaikat MB, Kodur VK (2010) Fire induced spalling in high strength concrete beams. Fire Technol 46(1):6. https://doi.org/10.1007/s10694-009-0088-610.1007/s10694-009-0088-6 ↗
15. Almeshal I, Abu Bakar BH, Tayeh BA (2022) Behaviour of reinforced concrete walls under fire: a review. Fire Technol 58:2589–2639. https://doi.org/10.1007/s10694-022-01240-310.1007/s10694-022-01240-3 ↗
16. Ghazy MF, Abd Elaty MA, Zalhaf NZ (2021) Prediction of temperature distribution and fire resistance of RC slab using artificial neural networks. Int J Struct Eng 11(1):1–1810.1504/IJSTRUCTE.2021.112084 ↗
17. d’Entremont FP, Poitras GJ (2022) Bending strength of composite slabs exposed to fire at an early age. Fire Technol 58:3509–3527. https://doi.org/10.1007/s10694-022-01315-110.1007/s10694-022-01315-1 ↗
18. Ghazy MF, Abd Elaty MA, Zalhaf NM (2022) Modeling the performance of reinforced concrete slabs cast with high performance concrete under fire. Innov Infrastruct Solut 7:210.1007/s41062-022-00770-7 ↗
19. Heikal M, El-Didamony H, Sokkary TM (2013) Behavior of composite cement pastes containing microsilica and fly ash at elevated temperature. Constr Build Mater 38:1180–1190. https://doi.org/10.1016/j.conbuildmat.2012.09.06910.1016/j.conbuildmat.2012.09.069 ↗
20. Khaliq W, Kodur V (2018) Effectiveness of polypropylene and steel fibers in enhancing fire resistance of high-strength concrete columns. J Struct Eng 144(3):1981. https://doi.org/10.1061/(ASCE)ST.1943-541X.000198110.1061/(ASCE)ST.1943-541X.0001981 ↗
21. Algourdin N, Pliya P, Beaucour A-L et al (2020) Influence of polypropylene and steel fibres on thermal spalling and physical-mechanical properties of concrete under different heating rates. Constr Build Mater 259:119690. https://doi.org/10.1016/j.conbuildmat.2020.11969010.1016/j.conbuildmat.2020.119690 ↗
22. Kodur VKR (2000) Spalling in high strength concrete exposed to fire––concerns, causes, critical parameters and cures. In: ASCE structures congress proceedings. Philadelphia, pp 1–810.1061/40492(2000)180 ↗
23. Shariq M, Khan AA, Masood A et al (2021) Experimental and analytical study of flexural response of RC beams with steel fibers after elevated temperature. Iran J Sci Technol Trans Civil Eng 45:611–628. https://doi.org/10.1007/s40996-020-00408-710.1007/s40996-020-00408-7 ↗
24. Poon C-S, Azhar S, Anson M et al (2001) Comparison of the strength and durability performance of normal-and high-strength pozzolanic concretes at elevated temperatures. Cem Concr Res 31(9):1291–1300. https://doi.org/10.1016/S0008-8846(01)00580-410.1016/S0008-8846(01)00580-4 ↗
25. Khaliq W, Kodur V (2013) Behavior of high strength fly ash concrete columns under fire conditions. Mater Struct 46:857–867. https://doi.org/10.1617/s11527-012-9938-710.1617/s11527-012-9938-7 ↗
26. Khan MS, Abbas H (2014) Effect of elevated temperature on the behavior of high volume fly ash Concrete. KSCE J Civ Eng 19(6):1–7. https://doi.org/10.1007/s12205-014-1092-z10.1007/s12205-014-1092-z ↗
27. Tanyildizi H, Coskun A (2008) The effect of high temperature on compressive strength and splitting tensile strength of structural lightweight concrete containing fly ash. Constr Build Mater 22(11):2269–2275. https://doi.org/10.1016/j.conbuildmat.2007.07.03310.1016/j.conbuildmat.2007.07.033 ↗
28. Babalola OE, Awoyera PO, Le DH et al (2021) A review of residual strength properties of normal and high strength concrete exposed to elevated temperatures: impact of materials modification on behaviour of concrete composite. Constr Build Mater 296:123448. https://doi.org/10.1016/j.conbuildmat.2021.12344810.1016/j.conbuildmat.2021.123448 ↗
29. Ghazy MF, Abd Elaty MA, Zalhaf NZ (2022) Mechanical properties of hpc incorporating fly ash and ground granulated blast furnace slag after exposure to high temperatures. Period Polytech Civ Eng. https://doi.org/10.3311/PPci.1975110.3311/PPci.19751 ↗
30. Xiao J, Falkner H (2006) On residual strength of high-performance concrete with and without polypropylene fibres at elevates temperatures. Fire Saf J 41:115–12110.1016/j.firesaf.2005.11.004 ↗
31. Behnood A, Ghandehari M (2009) Comparison of compressive and splitting tensile strength of high-strength concrete with and without polypropylene fibers heated to high temperatures. Fire Saf J. https://doi.org/10.1016/j.firesaf.2009.07.00110.1016/j.firesaf.2009.07.001 ↗
32. Ding Y, Azevedo C, Aguiar J, Jalali S (2012) Study on residual behaviour and flexural toughness of fibre cocktail reinforced self compacting high performance concrete after exposure to high temperature. Constr Build Mater 26(1):21–31. https://doi.org/10.1016/j.conbuildmat.2011.04.05810.1016/j.conbuildmat.2011.04.058 ↗
33. Abdul-Rahman M, Al-Attar AA, Hamada HM et al (2020) Microstructure and structural analysis of polypropylene fibre reinforced reactive powder concrete beams exposed to elevated temperature. J Build Eng 29:101167. https://doi.org/10.1016/j.jobe.2019.10116710.1016/j.jobe.2019.101167 ↗
34. Du H, Zhang M (2020) Experimental investigation of thermal pore pressure in reinforced C80 high performance concrete slabs at elevated temperatures. Constr Build Mater 260:12045110.1016/j.conbuildmat.2020.120451 ↗
35. Jafarzadeh H, Nematzadeh M (2020) Evaluation of post-heating flexural behavior of steel fiber-reinforced high-strength concrete beams reinforced with FRP bars: experimental and analytical results. Eng Struct 225:111292. https://doi.org/10.1016/j.engstruct.2020.11129210.1016/j.engstruct.2020.111292 ↗
36. Haddad RH, Al-Saleh RJ, Al-Akhras NM (2008) Effect of elevated temperature on bond between steel reinforcement and fiber reinforced concrete. Fire Saf J 43:334–34310.1016/j.firesaf.2007.11.002 ↗
37. Yermak N, Pliya P, Beaucour A-L et al (2017) Influence of steel and/or polypropylene fibres on the behaviour of concrete at high temperature: spalling, transfer and mechanical properties. Constr Build Mater 132:240–250. https://doi.org/10.1016/j.conbuildmat.2016.11.12010.1016/j.conbuildmat.2016.11.120 ↗
38. Monte FL, Felicetti R, Rossino C (2019) Fire spalling sensitivity of high-performance concrete in heated slabs under biaxial compressive loading. Mater Struct. https://doi.org/10.1617/s11527-019-1318-010.1617/s11527-019-1318-0 ↗
39. Randl N (2013) Design recommendations for interface shear transfer in fib Model Code 2010. Struct Concr 14:230–24110.1002/suco.201300003 ↗
40. Fernandes H, Lúcio V, Ramos A (2017) Strengthening of RC slabs with reinforced concrete overlay on the tensile face. Eng Struct 132:540–55010.1016/j.engstruct.2016.10.011 ↗
41. Xu Q, Chen L, Li X et al (2020) Comparative experimental study of fire resistance of two-way restrained and unrestrained precast concrete composite slabs. Fire Saf J 18:103225. https://doi.org/10.1016/j.firesaf.2020.10322510.1016/j.firesaf.2020.103225 ↗
42. Ahmad S, Bhargava P, Chourasia A et al (2020) Shear transfer strength of uncracked concrete after elevated temperatures. J Struct Eng 146:710.1061/(ASCE)ST.1943-541X.0002681 ↗
43. Xiao J, Li Z, Li J (2014) Shear transfer across a crack in high-strength concrete after elevated temperatures. Constr Build Mater 71:472–48310.1016/j.conbuildmat.2014.08.074 ↗
44. Blontrock H, Taerwe L, Vandevelde P (2000) Fire tests on concrete beams strengthened with fibre composites laminates. In: Proceedings of the 3rd International PhD Symposium in Civil Engineering. Vienna, Austria. http://hdl.handle.net/1854/LU-130382
45. EN 196-1 (2016) Cement—part 1: methods of testing cement-part 1: determination of strength. British Standards Institution, London
46. ES 4756 (2013) Cement part (1) composition, specifications and conformity criteria for common cements. British Standards Institution, London
47. ASTM-C127-01 (2017) Standard test method for density, relative density (specific gravity), and absorption of coarse aggregate. ASTM International, Wes Conshohocken
48. ASTM C128-01 (2017) Standard test method for density, relative density (specific gravity), and absorption of fine aggregate. ASTM International, West Conshohocken
49. ASTM C29/C29M-07 (2010) Standard test method for bulk density (“unit weight”) and voids in aggregate. ASTM International, West Conshohocken
50. ASTM C136/C136M-19 (2020) Standard test method for sieve analysis of fine and coarse aggregates. ASTM International, West Conshohocken
51. ASTM C494/C494M (2019) Standard specification for chemical admixtures for concrete. ASTM, West Conshohocken
52. Gao D, Yan D, Li X (2012) Splitting strength of GGBFS concrete incorporating with steel fiber and polypropylene fiber after exposure to elevated temperatures. Fire Saf J 54:67–7310.1016/j.firesaf.2012.07.009 ↗
53. BS EN 12390-3 (2019) Testing hardened concrete compressive strength of test specimens. British Standards Institution, London
54. BS EN 12390-6 (2009) Testing hardened concrete tensile splitting strength of test specimens. British Standards Institution, London
55. BS EN 12390-5 (2019) Testing hardened concrete flexural strength of test specimens. British Standards Institution, London
56. ACI Committee 318 (2014) Building code requirements for structural concrete (ACI318R-14). American Concrete Institute, Michigan
57. Coz-Díaz JJ, Martínez EJ, Martínez MA et al (2020) Comparative study of light weight and normal concrete composite slabs behaviour under fire conditions. Eng Struct. 207:110196. https://doi.org/10.1016/j.engstruct.2020.11019610.1016/j.engstruct.2020.110196 ↗
58. Priestley MJN, Seible F, Calvi GM (1996) Seismic design and retrofit of bridges. Wiley, New York10.1002/9780470172858 ↗
59. Mansour W, Fayed S (2021) Flexural rigidity and ductility of RC beams reinforced with steel and recycled plastic fibers. Steel Compos Struct 41(3):317–334. https://doi.org/10.12989/SCS.2021.41.3.31710.12989/SCS.2021.41.3.317 ↗
60. Akca AH, Özyurt N (2020) Post-fire mechanical behavior and recovery of structural reinforced concrete beams. Constr Build Mater 253:119188. https://doi.org/10.1016/j.conbuildmat.2020.11918810.1016/j.conbuildmat.2020.119188 ↗
61. Turker K, Hasgul U, Birol T et al (2019) Hybrid fiber use on flexural behavior of ultra-high performance fiber reinforced concrete beams. Compos Struct 229:111400. https://doi.org/10.1016/j.compstruct.2019.11140010.1016/j.compstruct.2019.111400 ↗
62. Ahmed RH, Abdel-Hameed GD, Farahat AM (2016) Behavior of hybrid high-strength fiber reinforced concrete slab-column connections under the effect of high temperature. HBRC J 12:54–6210.1016/j.hbrcj.2016.01.007 ↗
63. Mansour W, Fayed S (2021) Effect of interfacial surface preparation technique on bond characteristics of both NSC-UHPFRC and NSC-NSC composites. Structure 29:147–16610.1016/j.istruc.2020.11.010 ↗
64. Kodur V, Banerji S (2021) Modeling the fire-induced spalling in concrete structures incorporating hydro-thermo-mechanical stresses. Cem Concr Compos 117:10390210.1016/j.cemconcomp.2020.103902 ↗
65. Li Y, Tan KH, Yang EH (2019) Synergistic effects of hybrid polypropylene and steel fibers on explosive spalling prevention of ultra-high performance concrete at elevated temperature. Cem Concr Compos 96:174–18110.1016/j.cemconcomp.2018.11.009 ↗
66. Teng L, Khayat KH (2022) Effect of overlay thickness, fiber volume, and shrinkage mitigation on flexural behavior of thin bonded ultra-high-performance concrete overlay slab. Cem Concr Compos 134:10475210.1016/j.cemconcomp.2022.104752 ↗
67. Zhang Y, Zhu Y, Yeseta M et al (2019) Flexural behaviors and capacity prediction on damaged reinforcement concrete (RC) bridge deck strengthened by ultra-high performance concrete (UHPC) layer. Constr Build Mater 215:347–35910.1016/j.conbuildmat.2019.04.229 ↗
68. Zhou T, Sheng X (2022) Experimental study of flexural performance of UHPC–NC laminated beams exposed to fire. Materials 15:260510.3390/ma15072605 ↗
69. Lie TT, Leir G (1979) Factors affecting temperature of fire-exposed concrete slabs. Fire Mater 3(2):74–7910.1002/fam.810030204 ↗
70. FIB (2013) Fib model code for concrete structures 2010. Ernst Sohn Publication, New York, p 43410.1002/9783433604090 ↗
71. Qi J, Cheng Z, Wang J, Zhu Y, Li W (2020) Full-scale testing on the flexural behavior of an innovative dovetail UHPC joint of composite bridges. Struct Eng Mech 75:49–57
72. Erdem H (2010) Prediction of the moment capacity of reinforced concrete slabs in fire using artificial neural networks. Adv Eng Softw 41:270–27610.1016/j.advengsoft.2009.07.006 ↗
73. EN 1993-1-2 (2005) Eurocode 3: design of steel structures-part 1–2: general rules-structural fire design. European Committee for Standardization, Brussels
74. Jafarzadeh H, Nematzadeh M (2020) Evaluation of post-heating flexural behavior of steel fiber-reinforced high-strength concrete beams reinforced with FRP bars: experimental and analytical results. Eng Struct 225:11129210.1016/j.engstruct.2020.111292 ↗