Measurement and Prediction of Residual Stresses in Quenched Stainless Steel Components
Source abstract
Abstract
Austenitic stainless steel cylinders and rings are spray water quenched to create residual stresses at or greater than the yield strength. The residual stresses are measured using neutron diffraction, and two mechanical strain relaxation methods: deep hole drilling and incremental centre hole drilling. This paper compares the measurements with predictions of quenching using finite element analysis. Also finite element analysis is used to mimic deep hole and incremental centre hole drilling methods and to reconstruct residual stresses as if they have been measured. The measurements reveal similar trends to the predictions but there is only limited agreement between their magnitudes. However, there is better agreement between the reconstructed stresses and the measurements. Both the two mechanical strain relaxation methods reveal that large discrepancies occur between measurements and predictions arise because of plasticity. Irrespective of this and surprisingly there is good agreement between deep hole drilling and neutron diffraction measurements.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Welding Techniques and Residual Stresses · Microstructure and Mechanical Properties of Steels · Advanced machining processes and optimization
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (30)
Show source-provided references
1. Gur CH, Tekkaya AE (1999) Numerical and experimental analysis of quenched induced stresses and microstructures. J Mech Behav Mater 9(4):237–25610.1515/JMBM.1998.9.4.237 ↗
2. Mackerle J (2003) Finite element analysis and simulation of quenching and other heat treatment processes, a bibliography (1976–2001). Comput Mater Sci 27(3):313–33210.1016/S0927-0256(03)00038-7 ↗
3. Grum J, Kek T, Zupancic M, Batista M, Kosel F (2008) Measurement and numerical analysis of surface residual stresses occuring under different quenching conditions. Int J Microstruct Mater Prop 3(1):86–99
4. Lacarac, Smith, D.J., McMahon, C. and Tierney, M.J. A non-dimensional approach for estimation of residual stresses during cooling in steel Part 2 :With phase transformation. In: 1st ASM International Surface Engineering Conference and the 13th IFHTSE Congress, Columbus, OH, USA, 7–10 Oct. 2002. pp 578–587
5. Huang DJ, Mayo WE, Chen Y (1988) Residual-stress measurements in time-controlled quenched austenitic stainless steel. Exp Mech 28(4):359–36310.1007/BF02325177 ↗
6. Silva EP, Pacheco PMCL, Savi MA (2005) Finite element analysis of the phase transformation effect in the residual stresses generated by quenching in notched steel cylinders. J Strain Anal Eng Des 40(2):151–16010.1243/030932405X7755 ↗
7. Maniruzzaman M, Sisson RD Jr (2004) Heat transfer coefficients for quenching process simulation. J Phys IV France 120:521–52810.1051/jp4:2004120060 ↗
8. Li YY, Chen Y (1988) Modelling quenching to predict residual stress and microstructure distribution. J Eng Mater Technol 110(4):372–37910.1115/1.3226065 ↗
9. Sen S, Aksakal B, Ozel A (2000) Transient and thermal stresses in quenched cylindrical bodies. Int J Mech Sci 42(10):2013–202910.1016/S0020-7403(99)00063-6 ↗
10. Zabaras N, Mukherjee S, Arthur WR (1987) A numerical and experimental study of quenching of circular cylinders. J Therm Stresses 10(3):177–19110.1080/01495738708927007 ↗
11. Kang SH, Im YT (2007) Thermo-elasto-plastic finite element analysis of quenching process of carbon steel. J Mater Process Technol 192–193:381–39010.1016/j.jmatprotec.2007.04.101 ↗
12. Rai JK, Mishra A, Rao URK (1978) Some comments on residual stresses induced during quenching. Int J Prod Res 16(6):463–46710.1080/00207547808930037 ↗
13. Rathbun FO Jr, Coffin LF Jr (1966) An experimental investigation of residual stress in quenched flat plates. Exp Mech 6(10):519–52710.1007/BF02326525 ↗
14. Shi W, Liu Z, Yao K (2005) Prediction of internal stresses in large-size work pieces during intensive quenching basd on temperature-microstructure-stress coupled model. Int J Mater Prod Technol 24(1–4):385–39610.1504/IJMPT.2005.007963 ↗
15. Prime MB Residual stresses measured in quenched HSLA-100 steel plate. In: Proceedings the 2005 SEM Annual Conference and Exposition on Experimental and Applied Mechanics, Portland, OR, USA, 7–9 June, 2005. pp 1961–1967
16. Hossain S, Daymond MR, Truman CE, Smith DJ (2004) Prediction and measurmeent of residual stresses in quenched stainless-steel spheres. Mater Sci Eng A 373(1–2):339–34910.1016/j.msea.2004.02.014 ↗
17. Hossain S, Truman CE, Smith DJ, Daymond MR (2006) Application of quenching to create highly triaxial residual stresses in type 316 H stainless steel. Int J Mech Sci 48(3):235–24310.1016/j.ijmecsci.2005.11.002 ↗
18. Vorster WJJ, Korsunsky AM (2009) Analysis of residual strain and stress due to heat treatment and thermal processing. J Strain Anal Eng Des 44(1):71–9110.1243/03093247JSA418 ↗
19. Yazdi SR, Retraint D, Lu J (1998) Study of through-thickness residual stress by numerical and experimental techniques. J Strain Anal Eng Des 33(6):449–45810.1243/0309324981513147 ↗
20. Mahmoudi AH, Hossain S, Pavier MJ, Truman CE, Smith DJ (2009) A new procedure to measure near yield residual stresses using the deep hole drilling technique. Exp Mech 49(4):595–60410.1007/s11340-008-9164-y ↗
21. Mahmoudi AH, Pavier MJ, Truman CE, Smith DJ Accurate Measurement of Highly Triaxial Residual Stresses. In: Proceedings of the SEM Annual Conference and Exposition on Experimental and Applied Mechanics, 2007. pp 1836–1843
22. Grant PV, Lord PD, Whitehead PS (2002) The Measurement of Residual Stresses by the Incremental Hole Drilling Technique, Measurement Good Practice Guide 53. National Physical Library, Teddington
23. Schajer GS (1988) Measurement of non-uniform residual stresses using the hole drilling method. Part 1-stress calculation procedures. J Eng Mater Technol 110:338–34310.1115/1.3226059 ↗
24. Johnson MW, Daymond MR (2002) An optimum design for a time-of-flight neutron diffractometer for measuring engineering stresses. J Appl Crystallogr 35:49–5710.1107/S002188980101891X ↗
25. Hossain S (2005) Residual Stresses Under Conditions of High Triaxiality. PhD Thesis, University of Bristol
26. Daymond MR, Bourke MAM, Von Dreele RB, Clausen B, Lorentzen T (1997) Use of rietveld refinement for elastic macrostrain determination and for evaluation of plastic strain history from diffraction spectra. J Appl Phys 82(4):1554–156210.1063/1.365956 ↗
27. Hibbitt, Karlsson, Sorenson, Inc (2006) ABAQUS User Manuals Version 6.5. 1080 Main street, Pawtucket RI, 02860–4847, USA
28. Cemil Hakan Gür, Jiansheng Pan, Handbook of Thermal Process Modeling of Steels
29. Goudar DM, Smith DJ (2012) Validation of mechanical strain relaxation methods for stress measurement. Exp Mech. doi: 10.1007/s11340-012-9638-9
30. Beghini M, Bertini L, Santus C (2010) A procedure for evaluating high residual stresses using the blind hole drilling method, including the effects of plasticity. J Strain Anal 45:301–31810.1243/03093247JSA579 ↗