Review of engine journal bearing tribology in start-stop applications
Source abstract
Abstract
Abstract The environmental impacts of the air pollution from motorized transportation in the public health has driven new environmental regulations to reduce the gas emission produced by combustion engines. To address this issue, the automotive industry has developed strategies to meet these new requirements, and the start-stop systems emerge as a promising technology to reduce exhaust emissions and fuel consumption. However, the start-stop systems lead to high loads on the main engine components, such as piston, piston rings and bearings, since the temperature variation and lubrication supply are intermittent with the frequent engine start up. Thereby, the present study aims at presenting a literature review of the tribological aspects of car start-stop systems. A discussion of the operating parameters associated with the engine tribological behavior, mainly focused on the bearing crankshaft, is the core of this study. The review encompasses the recent bearing developments to meet the new load requirements, as well as the latest bearing researches regarding friction, lubrication and wear.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Tribology and Lubrication Engineering · Lubricants and Their Additives · Tribology and Wear Analysis
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (100+)
Show source-provided references
1. Air pollution from motor vehicles: standards and technologies for controlling emissions
2. M.a.M. Williams, R, A Technical Summary of Euro 6/VI Vehicle Emission Standards, ed: ICCT International council on clean transportation, 2016.
3. Effects of mixture enleanment in combustion and emission parameters using a flex-fuel engine with ethanol and gasoline10.1016/j.applthermaleng.2019.03.012 ↗
4. Combustion analysis of a SI engine with stratified and homogeneous pre-chamber ignition system using ethanol and hydrogen10.1016/j.applthermaleng.2019.113985 ↗
5. Practical control structure and energy management of a testbed hybrid electric vehicle10.1109/TVT.2011.2169821 ↗
6. Influence of the stop/start system on CO2 emissions of a diesel vehicle in urban traffic10.1016/j.trd.2010.10.001 ↗
7. J.W. George, R. Brock, Polymeric engine bearings for hybrid and start stop applications, SAE Technical Paper, 0148-7191, 2012.10.4271/2012-01-1966 ↗
8. S. Nebelsiek, Auslegung einer Methodik zur Verschleißermittlung an Triebwerkslagern, ed: Hochschule Esslingen - University of Applied Sciences, 2017.
9. N.D.S.A. Santos, Study of a bearing test bench capable to simulate wear in diesel start-stop engines, Master, UFMG, 2019.
10. P.R. Windover, R.J. Owens, T.M. Levinson, M.D. Laughlin, Stop and restart effects on modern vehicle starting system components: Longevity and economic factors, 2015.10.2172/1184379 ↗
11. J. Rueger, Clean diesel-real life fuel economy and environmental performance, in: SAE Government and Industry Meeting, Washington, DC, 2008.
12. P. Floraday, “Want stop-start technology on your next vehicle? Lobby the EPA”, ed: Automobile Magazine, 2009.
13. Back to square one: Identification issues in DSGE models10.1016/j.jmoneco.2009.03.014 ↗
14. Stop/start system integration to diesel engine and system modelling & validation10.3182/20130916-2-TR-4042.00008 ↗
15. Unified modeling of hybrid electric vehicle drivetrains10.1109/3516.789683 ↗
16. Mechatronic design and control of hybrid electric vehicles10.1109/3516.828590 ↗
17. Optimal control of a mechanical hybrid powertrain10.1109/TVT.2011.2178869 ↗
18. Control strategies for hybrid electric vehicles: Evolution, classification, comparison, and future trends10.1109/TVT.2007.899933 ↗
19. The state of the art of electric, hybrid, and fuel cell vehicles10.1109/JPROC.2007.892489 ↗
20. Optimal control of parallel hybrid electric vehicles based on theory of switched system10.1111/j.1934-6093.2006.tb00278.x ↗
21. Y. Gurkaynak, A. Khaligh, A. Emadi, State of the art power management algorithms for hybrid electric vehicles, in: Vehicle Power and Propulsion Conference, 2009. VPPC'09. IEEE, 2009: IEEE, pp. 388–394.10.1109/VPPC.2009.5289823 ↗
22. Threshold-changing control strategy for series hybrid electric vehicles10.1016/j.apenergy.2018.11.003 ↗
23. K. Kataoka, K. Tsuji, Crankshaft positioning utilizing compression force and fast starting with combustion assist for indirect injection engine, SAE Technical Paper, 0148-7191, 2005.10.4271/2005-01-1166 ↗
24. M.L. Kuang, An investigation of engine start-stop NVH in a power split powertrain hybrid electric vehicle, SAE Technical Paper, 0148-7191, 2006.10.4271/2006-01-1500 ↗
25. Minimizing seat track vibration that is caused by the automatic start/stop of an engine in a power-split hybrid electric vehicle10.1115/1.4023954 ↗
26. Experimental investigation of laser surface texturing for reciprocating automotive components10.1080/10402000208982572 ↗
27. Tribological property of plain bearing with low frictional layer10.1016/j.triboint.2009.02.007 ↗
28. Transient effects in engines operating at steady speeds & loads
29. Hamrock · 2004
30. Elasto-hydrodynamic lubrication: a survey of isothermal solutions10.1243/JMES_JOUR_1962_004_018_02 ↗
31. Taylor · 1985
32. The influence of start–stop transient velocity on the friction and wear behaviour of a hyper-eutectic Al–Si automotive alloy10.1016/j.wear.2012.11.007 ↗
33. A. King, “Non friction,” ed: Chemistry & Industry News, 2012.
34. Rogowski · 1953
35. Bowden · 2001
36. Hutchings · 2017
37. Estimation of friction distribution in partial-slip contacts from reciprocating full-sliding tests10.1016/j.triboint.2016.09.007 ↗
38. MATEC Web Conf. · 2017 · 112 · 0401410.1051/matecconf/201711204014 ↗
39. Bhushan · 2013
40. H. Zumbühl, Motoren - Ein Buch über Wärmekraftmaschinen und ihre Brennstoffe, ed: SDV-Fachbücher, 1946.
41. Failure criteria in thin film lubrication: investigation of the different stages of film failure10.1016/0043-1648(76)90139-3 ↗
42. Failure criteria in thin film lubrication—the IRG program10.1016/0043-1648(76)90137-X ↗
43. A note on the four-ball machine
44. B. Manual, Bearing Group Miba, Miba Gleitlager AG, 2000.
45. Stribeck · 1903
46. Affenzeller · 2013
47. Steinhilper · 2008
48. Williams · 2005
49. Wear simulation for the journal bearings operating under aligned shaft and steady load during start-up and coast-down conditions10.1016/j.triboint.2016.01.042 ↗
50. Rudnick · 2017
51. Rahnejat · 2010
52. Direct formation of lubricious and wear-protective carbon films from phosphorus-and sulfur-free oil-soluble additives10.1007/s11249-017-0945-2 ↗
53. Influence of numerous start-ups and stops on tribological performance evolution of engine main bearings
54. Fuel consumption and friction benefits of low viscosity engine oils for heavy duty applications10.1016/j.triboint.2017.02.007 ↗
55. Challenges of friction reduction of engine plain bearings–Tackling the problem with novel bearing materials10.1016/j.triboint.2018.10.042 ↗
56. Extending SAE J300 to viscosity grades below SAE 2010.4271/2010-01-2286 ↗
57. A review of automotive engine friction reduction opportunities through technologies related to tribology10.1007/s12666-016-1001-x ↗
58. ACEA, ACEA European Oil Sequences, ed, 2016.
59. Overview of automotive engine friction and reduction trends–Effects of surface, material, and lubricant-additive technologies10.1007/s40544-016-0107-9 ↗
60. Effects of oil warm up acceleration on the fuel consumption of reciprocating internal combustion engines10.1016/j.egypro.2015.11.870 ↗
61. The influence of contact pressure and saponification on the sliding behavior of stearic acid monolayers10.1016/0021-9797(77)90411-8 ↗
62. Rheology of thin organic films10.1080/05698197408981452 ↗
63. Friction modifier additives10.1007/s11249-015-0589-z ↗
64. Performance of friction modifiers on ZDDP-generated surfaces
65. Tribological performance of three advanced piston rings in the presence of MoDTC-modified GF-3 oils10.1007/s11249-004-1759-6 ↗
66. Formation and breakdown of oil residue tribofilms protecting the valves of diesel engines10.1016/j.wear.2015.01.066 ↗
67. A. Kovalchenko, O.O. Ajayi, A. Erdemir, G.R. Fenske, Friction and wear performance of low-friction carbon coatings under oil lubrication, SAE Transactions, 2002, pp. 902–910.10.4271/2002-01-1921 ↗
68. Wear and performance analysis of a 4-stroke diesel engine employing nanolubricants10.1016/j.partic.2017.05.016 ↗
69. The behavior of polymer solutions in concentrated contacts: immobile surface layer formation10.1080/10402009408983332 ↗
70. Predicting EHD film thickness of lubricant polymer solutions10.1080/10402009808983715 ↗
71. Copper oxide nano-particles as friction-reduction and anti-wear additives in lubricating oil10.1007/s12206-015-0141-y ↗
72. Proposing new hybrid nano-engine oil for lubrication of internal combustion engines: Preventing cold start engine damages and saving energy10.1016/j.energy.2018.12.127 ↗
73. Antagonistic interaction of antiwear additives and carbon black10.1007/s11249-009-9489-4 ↗
74. Additives for improving the fuel economy of diesel engine systems10.2474/trol.5.195 ↗
75. Tribological bench and engine dynamometer tests of a low viscosity SAE 0W–16 engine oil using a combination of ionic liquid and ZDDP as anti-wear additives10.3389/fmech.2015.00012 ↗
76. O.R.G.o.W.o.E. Materials, Friction, Wear and Lubrication - Tribology of Terms and Definition, ed: OECD, 1969.
77. D.I.f. Normung, DIN 50320: Verscheiss - Begriff, Analyse von Verschleissvorgängen, Gliederung des Verschleissgebietes, ed: Beuth Verlag, 1979.
78. Theories of wear and their significance for engineering practice10.1016/S0161-9160(13)70065-6 ↗
79. Zum-gahr · 1987
80. Contact and rubbing of flat surfaces10.1063/1.1721448 ↗
81. G. Stachowiak, A. Batchelor, T. Stolarski, Engineering tribology: Elsevier, 1993, ISBN 0-444-89235-4, 960 pp,£ 156.00, ed: Elsevier, 1994.
82. Mahle, “Gleitlager,” Zylinderkomponenten: Eigenschaften, Anwendungen, Werkstoffe, 2009, pp. 49–69.10.1007/978-3-8348-9686-5_3 ↗
83. L. Tambellini, L. Oliveira, M. Tsubouchi, Bearing Fundamentals, ed: MAHLE Metal Leve S.A., GEA-B, 2007.
84. Friction and wear characteristics of different Pb-free bearing materials in mixed and boundary lubrication regimes10.1016/j.wear.2015.06.002 ↗
85. M. GmbH, “Gleitlager,” Zylinderkomponenten: Eigenschaften, Anwendungen, Werkstoffe, 2009, pp. 49–69.10.1007/978-3-8348-9686-5_3 ↗
86. Tribological performance of thin overlays for journal bearings10.1016/j.triboint.2010.10.027 ↗
87. Materials for plain bearings10.1179/imr.1973.18.2.62 ↗
88. Trends in tribological materials and engine technology10.1016/j.triboint.2003.12.006 ↗
89. High strength tin-based overlay for medium and high speed diesel engine bearing tribological applications10.1016/j.triboint.2015.03.010 ↗
90. Crankshaft bearings for engines with start-stop systems10.1007/BF03228047 ↗
91. F.M. Powertrain, Application Engineering FM Bearings, ed: Federal Mogul Powertrain, 2010.
92. J. Häring, IROX II - Neue Hochleistungspollymerbeschichtung für Gleitlager, ed: VDI Wissenforum, 2018.10.51202/9783181023174-153 ↗
93. Seizure behaviour of some selected Pb-free engine bearing materials under lubricated condition10.1016/j.triboint.2017.03.021 ↗
94. ACEA, ACEA 2016 European Oil for Service-Fill Oils, ed, 2016.
95. Tribological effects of mineral-oil lubricant contamination with biofuels: a pin-on-disk tribometry and wear study10.1155/2011/820795 ↗
96. Stabilizing slider-crank mechanism with clearance joints10.1016/j.mechmachtheory.2012.02.006 ↗
97. A method for contact analysis of revolute joints with noncircular clearance in a planar multibody system
98. A procedure for constructing a theoretical wear diagram of IC engine crankshaft main bearings10.1016/j.mechmachtheory.2012.07.009 ↗
99. Prediction of wear in grease-lubricated oscillatory journal bearings via energy-based approach10.1016/j.wear.2014.06.022 ↗
100. Wear simulation in non-lubricated and mixed lubricated contacts taking into account the microscale roughness10.1016/j.triboint.2016.02.009 ↗