journal article·2018-01

Microscale 3D Printing of Nanotwinned Copper

Ali Behroozfar, Soheil Daryadel, S. Reza Morsali, Salvador Moreno, Mahmoud Baniasadi, Rodrigo A. Bernal, Majid Minary‐Jolandan

Advanced Materials· Volume 30· Issue 4
Publisher page

Abstract

Abstract Nanotwinned (nt)‐metals exhibit superior mechanical and electrical properties compared to their coarse‐grained and nanograined counterparts. nt‐metals in film and bulk forms are obtained using physical and chemical processes including pulsed electrodeposition (PED), plastic deformation, recrystallization, phase transformation, and sputter deposition. However, currently, there is no process for 3D printing (additive manufacturing) of nt‐metals. Microscale 3D printing of nt‐Cu is demonstrated with high density of coherent twin boundaries using a new room temperature process based on localized PED (L‐PED). The 3D printed nt‐Cu is fully dense, with low to none impurities, and low microstructural defects, and without obvious interface between printed layers, which overall result in good mechanical and electrical properties, without any postprocessing steps. The L‐PED process enables direct 3D printing of layer‐by‐layer and complex 3D microscale nt‐Cu structures, which may find applications for fabrication of metamaterials, sensors, plasmonics, and micro/nanoelectromechanical systems.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Microstructure and mechanical properties · Metal and Thin Film Mechanics · Electrodeposition and Electroless Coatings

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Department of Mechanical Engineering The University of Texas at Dallas Richardson TX 75080 USA

Alan G. MacDiarmid NanoTech Institute The University of Texas at Dallas Richardson TX 75080 USA

Funding

Office of Naval Research

References (37)

Show source-provided references
1. 10.1126/science.109290510.1126/science.1092905 ↗
2. 10.1146/annurev-matsci-070813-11330410.1146/annurev-matsci-070813-113304 ↗
3. 10.1126/science.116764110.1126/science.1167641 ↗
4. 10.1126/science.115961010.1126/science.1159610 ↗
5. 10.1038/natrevmats.2016.1910.1038/natrevmats.2016.19 ↗
6. 10.1038/nmat364610.1038/nmat3646 ↗
7. 10.1038/nnano.2012.11610.1038/nnano.2012.116 ↗
8. 10.1038/nature0892910.1038/nature08929 ↗
9. 10.1038/ncomms276810.1038/ncomms2768 ↗
10. 10.1016/j.actamat.2003.08.03210.1016/j.actamat.2003.08.032 ↗
11. Ovid'ko I. A. · Rev. Adv. Mater. Sci. · 2016 · 44 · 1
12. 10.1557/mrs.2016.6010.1557/mrs.2016.60 ↗
13. 10.1126/science.116077710.1126/science.1160777 ↗
14. 10.1557/mrs.2016.6210.1557/mrs.2016.62 ↗
15. 10.1126/science.116837510.1126/science.1168375 ↗
16. 10.1126/science.aaf209310.1126/science.aaf2093 ↗
17. 10.1002/adma.20160421110.1002/adma.201604211 ↗
18. 10.1126/science.119049610.1126/science.1190496 ↗
19. 10.1063/1.217753810.1063/1.2177538 ↗
20. 10.1088/0960-1317/17/6/01310.1088/0960-1317/17/6/013 ↗
21. 10.1002/adma.20150496710.1002/adma.201504967 ↗
22. 10.1021/nl902872w10.1021/nl902872w ↗
23. 10.1126/science.121651110.1126/science.1216511 ↗
24. 10.1021/cg300962v10.1021/cg300962v ↗
25. 10.1021/nl200307610.1021/nl2003076 ↗
26. 10.1016/j.electacta.2015.08.02210.1016/j.electacta.2015.08.022 ↗
27. 10.1063/1.306819110.1063/1.3068191 ↗
28. 10.1063/1.348968910.1063/1.3489689 ↗
29. 10.1016/j.electacta.2007.11.05410.1016/j.electacta.2007.11.054 ↗
30. 10.1038/ncomms238210.1038/ncomms2382 ↗
31. 10.1038/srep0612310.1038/srep06123 ↗
32. 10.1016/j.surfcoat.2004.05.00110.1016/j.surfcoat.2004.05.001 ↗
33. 10.1088/0957-4484/17/1/01210.1088/0957-4484/17/1/012 ↗
34. 10.1016/j.actamat.2013.08.03710.1016/j.actamat.2013.08.037 ↗
35. 10.1016/j.actamat.2012.03.02010.1016/j.actamat.2012.03.020 ↗
36. 10.1016/j.actamat.2005.01.03110.1016/j.actamat.2005.01.031 ↗
37. 10.1063/1.473124210.1063/1.4731242 ↗