Comparative Study of TiMn and TiAlV Alloys via the Nanoindentation Technique
Source abstract
Abstract
There are two common categories of implants that are used in medical sciences, i.e., orthopedic and dental ones. In this study, dental implant materials are focused such as Ti6Al4V alloys that are used for the replacement of lost teeth due to their high strength and biocompatibility. However, they cause infections in nearby tissues due to elemental release (potentially Al and V). Thus, manganese is selected to be incorporated into the alloy since it is also present in the human body in the form of traces. Different sets of implants were produced, i.e., Ti5Mn and Ti10Mn (where 5 and 10 describe the percentage of Mn) by using the powder metallurgy technique. This was followed by characterization techniques, including X-ray fluorescence spectroscopy (XRF), X-ray diffractometer (XRD), optical microscope (OM), and nanoindenter. The very aim of this study is to compare the microstructural evolutions, density, and mechanical properties of reference alloys and the ones produced in this study. Results show the microstructure of Ti6Al4V consists of the alpha (α) and beta (β) phases, while Ti5Mn and Ti10Mn revealed the beta (β) phases. The Ti5Mn alloy showed excellent mechanical properties than that of the Ti6Al4V counterpart. Extensive discussion is presented in light of the observed results. The relative density of Ti5Mn alloy was found to be enhanced than that of reference alloy.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Titanium Alloys Microstructure and Properties · Metal and Thin Film Mechanics · Orthopaedic implants and arthroplasty
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Materials and Surface Engineering Research Lab, Department of Metallurgical Engineering, NED University of Engineering and Technology, Karachi 75270, Pakistan
Thin Film Lab, Department of Metallurgical Engineering, NED University of Engineering and Technology, Karachi 75270, Pakistan
Department of Petroleum Technology, University of Karachi, Karachi 75270, Pakistan
Solar Factory of the Future, Bavarian Center for Applied Energy Research (ZAE Bayern), Fürther Straße 250, 90429 Nürnberg, Germany
Department of Mechanical & Energy Systems Engineering, Faculty of Engineering and Informatics, University of Bradford, Bradford BD7 1DP, UK
Department of Physics and Astronomy, College of Science, King Saud University, Riyadh 11451, Saudi Arabia
Funding
Researcher’s Supporting Project
References (38)
Show source-provided references
1. Selective modification of Ti6Al4V surfaces for biomedical applications10.1039/C9RA11000C ↗
2. Pollution and health: A progress update10.1016/S2542-5196(22)00090-0 ↗
3. Facile Coating of HAP on Ti6Al4V for Osseointegration10.48084/etasr.4155 ↗
4. Short term exposure to titanium, aluminum and vanadium (Ti 6Al 4V) alloy powder drastically affects behavior and antioxidant metabolites in vital organs of male albino mice10.1016/j.toxrep.2018.06.006 ↗
5. Link between Aluminum and the Pathogenesis of Alzheimer's Disease: The Integration of the Aluminum and Amyloid Cascade Hypotheses10.4061/2011/276393 ↗
6. Preparation, microstructures, mechanical properties, and cytocompatibility of TiMn alloys for biomedical applications10.1002/jbm.b.31668 ↗
7. Microscopic phase-segregated quaternary ammonia polysulfone membrane for vanadium redox flow batteries10.1016/j.jpowsour.2019.04.100 ↗
8. Antibacterial Ti-Mn-Cu alloys for biomedical applications10.1093/rb/rbaa050 ↗
9. Microelements for bone boost: The last but not the least
10. Fabrication of low-cost beta-type Ti–Mn alloys for biomedical applications by metal injection molding process and their mechanical properties10.1016/j.jmbbm.2016.02.035 ↗
11. Mechanical properties and microstructure of Ti-Mn alloys produced via powder metallurgy for biomedical applications10.1016/j.jmbbm.2018.12.005 ↗
12. Nanoindentation and wear properties of Ti and Ti-TiB composite materials produced by selective laser melting10.1016/j.msea.2017.01.096 ↗
13. Aluminum and aluminum nitrides effect on nucleation sites in micro-alloyed steel
14. Producing oxide free silicon nanocrystals—A novel & benign approach10.1016/j.ijleo.2021.167789 ↗
15. Comparison of the mechanical properties of dentin and enamel determined by different nanoindentation techniques: Conventional method and continuous stiffness measurement
16. Tuninetti, V., Jaramillo, A.F., Riu, G., Rojas-Ulloa, C., Znaidi, A., Medina, C., Mateo, A.M., and Roa, J.J. (2021). Experimental Correlation of Mechanical Properties of the Ti-6Al-4V Alloy at Different Length Scales. Metals, 11.10.3390/met11010104 ↗
17. A Review on Nano-Indentation of Thin Polymeric Films
18. Ashfaq, J., Channa, I.A., Shaikh, A.A., Chandio, A.D., Shah, A.A., Bughio, B., Birmahani, A., Alshehri, S., and Ghoneim, M.M. (2022). Gelatin-and Papaya-Based Biodegradable and Edible Packaging Films to Counter Plastic Waste Generation. Materials, 15.10.3390/ma15031046 ↗
19. Nanoindentation of coatings10.1088/0022-3727/38/24/R01 ↗
20. Effect of doping and loading Parameters on photocatalytic degradation of brilliant green using Sn doped ZnO loaded CSAC10.1016/j.envres.2022.112833 ↗
21. Mathematical Relationship between Ferritic, Pearlitic and Average Grain Size of Steel
22. Chen, L.-Y., Cui, Y.-W., and Zhang, L.-C. (2020). Recent Development in Beta Titanium Alloys for Biomedical Applications. Metals, 10.10.3390/met10091139 ↗
23. Nanoindentation study of mechanical properties of Ti based alloys with Fe and Ta additions
24. Microstructures, mechanical properties and cytotoxicity of low cost beta Ti–Mn alloys for biomedical applications10.1016/j.actbio.2015.08.015 ↗
25. Nanoindentation characterization on local plastic response of Ti-6Al-4V under high-load spherical indentation10.1016/j.jmrt.2019.06.009 ↗
26. Metallurgical analysis and nanoindentation characterization of Ti–6Al–4V workpiece and chips in high-throughput drilling10.1016/j.msea.2007.03.054 ↗
27. Azmat, A., Tufail, M., and Chandio, A.D. (2021). Synthesis and Characterization of Ti-Sn Alloy for Orthopedic Application. Materials, 14.10.3390/ma14247660 ↗
28. Effect of Manganese Addition on the Microstructure and Mechanical Properties of Ti-Nb Biomedical Alloys10.1088/1755-1315/252/2/022137 ↗
29. Nanoindentation studies on TiN nanoceramic reinforced Ti–6Al–4V matrix composite10.1016/j.ceramint.2017.12.042 ↗
30. Corrosion resistance of Ti-6Al-4V and ASTM F75 alloys processed by electron beam melting10.1016/j.jmrt.2017.05.003 ↗
31. Electrochemical behavior of near-beta titanium biomedical alloys in phosphate buffer saline solution10.1016/j.msec.2014.11.036 ↗
32. Fabrication, characterization and permeation study of ultrafiltration dialysis membranes10.1080/19443994.2016.1149108 ↗
33. Santos, P.F., Niinomi, M., Liu, H., Nakai, M., Cho, K., Narushima, T., Ueda, K., Ohtsu, N., Hirano, M., and Itoh, Y. (2017). Development and Performance of Low-Cost Beta-Type Ti-Based Alloys for Biomedical Applications Using Mn Additions BT. Interface Oral Health Science 2016, Springer.10.1007/978-981-10-1560-1_19 ↗
34. Ran, J., Jiang, F., Sun, X., Chen, Z., Tian, C., and Zhao, H. (2020). Microstructure and Mechanical Properties of Ti-6Al-4V Fabricated by Electron Beam Melting. Crystals, 10.10.3390/cryst10110972 ↗
35. Influence of Fe Content of Ti-Mn-Fe Alloys on Phase Constitution and Heat Treatment Behavior10.4028/www.scientific.net/MSF.706-709.1893 ↗
36. Voyiadjis, G.Z., and Yaghoobi, M. (2017). Review of Nanoindentation Size Effect: Experiments and Atomistic Simulation. Crystals, 7.10.3390/cryst7100321 ↗
37. Elastic modulus of biomedical titanium alloys by nano-indentation and ultrasonic techniques—A comparative study10.1016/j.msea.2007.12.029 ↗
38. Ti-based composite materials with enhanced thermal and mechanical properties10.1016/j.ceramint.2020.08.207 ↗