Surface Topography Generated in Milling of Porous Titanium: Porosity, Roughness, and Fractal Analysis
Source abstract
Abstract
Milling‐induced surface topography of porous titanium, critical for its functional performance, is governed by cellular pore deformation. This study establishes how milling parameters control this deformation to tailor the generated surface topography in terms of porosity, roughness, and fractal dimension. The key finding is that the axial depth of cut dictates the deformation mode: low depths (≤1.5 mm) promote plastic smearing, reducing surface porosity by up to 49% for densified surfaces, while high depths (≥2.0 mm) trigger brittle peeling, increasing porosity by up to 74% for enhanced permeability or osseointegration. Areal roughness ( S a : 40.69–114.95 μm) is primarily governed by pore‐induced topography, with axial depth being the most influential parameter (65.85% contribution). Fractal dimension (1.39–1.95) peaks at a 2.0 mm depth, indicating maximum complexity from pore fragmentation. These insights provide a direct parameter selection framework for engineering porous titanium surfaces to meet application‐specific demands.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Advanced machining processes and optimization · Calcium Carbonate Crystallization and Inhibition · Cellular and Composite Structures
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Department of Mechanical Engineering Anhui University Hefei Anhui 230601 China
Funding
National Natural Science Foundation of China
References (35)
Show source-provided references
1. 10.1007/s40735-023-00760-x10.1007/s40735-023-00760-x ↗
2. 10.1002/adem.20170064810.1002/adem.201700648 ↗
3. 10.1080/10426914.2021.192869610.1080/10426914.2021.1928696 ↗
4. 10.1177/204129751039405710.1177/2041297510394057 ↗
5. 10.1080/10426914.2016.125780010.1080/10426914.2016.1257800 ↗
6. 10.1007/s12598-023-02570-z10.1007/s12598-023-02570-z ↗
7. 10.1590/S1516-1439200800030000810.1590/S1516-14392008000300008 ↗
8. 10.3390/met504190210.3390/met5041902 ↗
9. 10.1179/02670830322500432310.1179/026708303225004323 ↗
10. 10.1016/j.aej.2025.06.06310.1016/j.aej.2025.06.063 ↗
11. 10.1016/j.biomaterials.2006.08.01310.1016/j.biomaterials.2006.08.013 ↗
12. 10.3390/coatings1310171410.3390/coatings13101714 ↗
13. 10.1016/j.mtcomm.2022.10500310.1016/j.mtcomm.2022.105003 ↗
14. 10.1016/S0079-6425(00)00002-510.1016/S0079-6425(00)00002-5 ↗
15. 10.1016/j.precisioneng.2022.04.01010.1016/j.precisioneng.2022.04.010 ↗
16. 10.1016/j.precisioneng.2018.01.01410.1016/j.precisioneng.2018.01.014 ↗
17. 10.1007/s00170-020-05466-910.1007/s00170-020-05466-9 ↗
18. 10.1016/j.ijmecsci.2022.10768610.1016/j.ijmecsci.2022.107686 ↗
19. 10.1016/j.apt.2017.02.02110.1016/j.apt.2017.02.021 ↗
20. 10.1007/s00170-011-3647-110.1007/s00170-011-3647-1 ↗
21. 10.1016/j.jmatprotec.2015.10.00210.1016/j.jmatprotec.2015.10.002 ↗
22. 10.1016/j.precisioneng.2015.12.00410.1016/j.precisioneng.2015.12.004 ↗
23. 10.1016/j.ijrmhm.2012.04.00910.1016/j.ijrmhm.2012.04.009 ↗
24. Heidari M. · Int. J. Addit. Subtractive Mater. Manuf. · 2017 · 1 · 23
25. 10.1016/j.jmst.2020.11.00510.1016/j.jmst.2020.11.005 ↗
26. 10.1007/s00170-023-11318-z10.1007/s00170-023-11318-z ↗
27. 10.1007/s00170-015-7849-910.1007/s00170-015-7849-9 ↗
28. 10.1111/j.1600-0501.2009.01775.x10.1111/j.1600-0501.2009.01775.x ↗
29. 10.1016/j.triboint.2016.09.03610.1016/j.triboint.2016.09.036 ↗
30. 10.1016/0890-6955(93)90089-D10.1016/0890-6955(93)90089-D ↗
31. 10.1016/j.precisioneng.2024.06.01810.1016/j.precisioneng.2024.06.018 ↗
32. 10.1016/j.apsusc.2013.05.12310.1016/j.apsusc.2013.05.123 ↗
33. 10.1016/j.powtec.2023.11825610.1016/j.powtec.2023.118256 ↗
34. 10.1016/j.powtec.2025.12077410.1016/j.powtec.2025.120774 ↗
35. 10.1016/j.ijthermalsci.2022.10798510.1016/j.ijthermalsci.2022.107985 ↗