journal article·2024-10

Effects of Cold‐Rolling and Subsequent Annealing on Microstructure and Mechanical Properties of (CrCoNi) 97 Al 1.5 Ti 1.5 Medium‐Entropy Alloy

Liming Zhong, Xiaolian Liu, Fujian Zhang, Yanxia Chen, Shengfeng Guo, Ning Guo

Advanced Engineering Materials· Volume 26· Issue 20
Publisher page

Abstract

In this study, the (CrCoNi) 97 Al 1.5 Ti 1.5 medium‐entropy alloy (MEA) is prepared and subjected to cold‐rolling and annealing. The phase and microstructure are characterized by using X‐ray diffraction (XRD), backscattered electron imaging (BSEI), electron backscattered diffraction (EBSD), and transmission Kikuchi diffraction (TKD). Microhardness and tensile properties of the deformed and annealed samples are measured. The results show that a large amount of lamellar dislocation substructures (LDS) is formed during cold‐rolling up to 50% reduction. After a 50% rolling reduction and annealing at 600 °C for 1 h, the LDS inside the deformed grains does not change significantly. When the annealing temperature increases to 650 °C, a large amount of LDS begins to disappear and is replaced by recrystallized grains and high‐density annealing twins. When the annealing temperature reaches 700 °C, a completely recrystallized structure is obtained. Cold‐rolling deformation leads to a linear increase in the microhardness and tensile strength of MEA. The 50% reduction sample will harden again after short‐time annealing at 600 °C while softening will occur after annealing at 650 °C or 700 °C. The deformation mechanisms and strengthening mechanisms are also discussed and analyzed.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: High Entropy Alloys Studies · High-Temperature Coating Behaviors · Intermetallics and Advanced Alloy Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

School of Materials and Energy Southwest University Chongqing 400715 China

Funding

Fundamental Research Funds for the Central Universities

References (62)

Show source-provided references
1. 10.1016/j.msea.2003.10.25710.1016/j.msea.2003.10.257 ↗
2. 10.1002/adem.20030056710.1002/adem.200300567 ↗
3. Li Y. C. · Rare Met. Mater. Eng. · 2020 · 49 · 4365
4. 10.1016/j.pmatsci.2018.12.00310.1016/j.pmatsci.2018.12.003 ↗
5. 10.1016/j.actamat.2016.04.00510.1016/j.actamat.2016.04.005 ↗
6. 10.1016/j.jallcom.2011.02.17110.1016/j.jallcom.2011.02.171 ↗
7. 10.1038/s41598-019-55762-y10.1038/s41598-019-55762-y ↗
8. 10.1126/science.125458110.1126/science.1254581 ↗
9. 10.1016/j.surfcoat.2023.12969510.1016/j.surfcoat.2023.129695 ↗
10. 10.1016/j.jallcom.2012.09.09110.1016/j.jallcom.2012.09.091 ↗
11. 10.1002/adem.20200046610.1002/adem.202000466 ↗
12. 10.1016/j.intermet.2016.09.00310.1016/j.intermet.2016.09.003 ↗
13. 10.20517/microstructures.2022.0210.20517/microstructures.2022.02 ↗
14. 10.1016/j.msea.2007.06.01410.1016/j.msea.2007.06.014 ↗
15. 10.1038/ncomms1060210.1038/ncomms10602 ↗
16. 10.1016/j.jmst.2021.08.05710.1016/j.jmst.2021.08.057 ↗
17. 10.1016/j.actamat.2017.04.03310.1016/j.actamat.2017.04.033 ↗
18. 10.1063/5.006726810.1063/5.0067268 ↗
19. 10.1016/j.actamat.2014.08.02610.1016/j.actamat.2014.08.026 ↗
20. 10.1016/j.actamat.2017.02.03610.1016/j.actamat.2017.02.036 ↗
21. 10.1016/j.actamat.2018.07.02810.1016/j.actamat.2018.07.028 ↗
22. 10.1016/j.msea.2004.01.06010.1016/j.msea.2004.01.060 ↗
23. 10.1016/j.msea.2004.01.05910.1016/j.msea.2004.01.059 ↗
24. 10.1016/j.actamat.2017.06.04610.1016/j.actamat.2017.06.046 ↗
25. 10.1016/j.msea.2010.02.04110.1016/j.msea.2010.02.041 ↗
26. 10.1016/j.jmst.2022.06.04810.1016/j.jmst.2022.06.048 ↗
27. 10.1016/j.msea.2021.14215310.1016/j.msea.2021.142153 ↗
28. 10.1016/j.actamat.2013.09.03710.1016/j.actamat.2013.09.037 ↗
29. 10.1016/S1003-6326(22)65946-610.1016/S1003-6326(22)65946-6 ↗
30. 10.1016/j.msea.2015.09.03410.1016/j.msea.2015.09.034 ↗
31. 10.1016/j.actamat.2015.08.07610.1016/j.actamat.2015.08.076 ↗
32. 10.1016/j.intermet.2016.09.00510.1016/j.intermet.2016.09.005 ↗
33. 10.1016/j.msea.2023.14553510.1016/j.msea.2023.145535 ↗
34. 10.1016/j.actamat.2008.11.03610.1016/j.actamat.2008.11.036 ↗
35. 10.1016/j.actamat.2018.05.00910.1016/j.actamat.2018.05.009 ↗
36. 10.1016/j.acme.2016.06.00510.1016/j.acme.2016.06.005 ↗
37. 10.1016/j.measurement.2015.08.03310.1016/j.measurement.2015.08.033 ↗
38. 10.1016/j.intermet.2018.07.01410.1016/j.intermet.2018.07.014 ↗
39. 10.1016/j.intermet.2019.10657810.1016/j.intermet.2019.106578 ↗
40. 10.1016/j.matchar.2022.11225410.1016/j.matchar.2022.112254 ↗
41. 10.1016/S1003-6326(22)65893-X10.1016/S1003-6326(22)65893-X ↗
42. 10.1126/science.109507110.1126/science.1095071 ↗
43. 10.1038/ncomms1571910.1038/ncomms15719 ↗
44. 10.1016/j.matchar.2014.05.01810.1016/j.matchar.2014.05.018 ↗
45. 10.1023/A:100866860473310.1023/A:1008668604733 ↗
46. 10.1016/j.actamat.2007.05.01910.1016/j.actamat.2007.05.019 ↗
47. 10.1016/j.msea.2022.14280210.1016/j.msea.2022.142802 ↗
48. 10.1016/j.jallcom.2019.15277710.1016/j.jallcom.2019.152777 ↗
49. 10.1016/S0921-5093(00)02019-010.1016/S0921-5093(00)02019-0 ↗
50. 10.1016/j.actamat.2009.12.03210.1016/j.actamat.2009.12.032 ↗
51. Raghavan K. S. · Trans. Metall. Soc. Aim. · 1969 · 245 · 1569
52. 10.1016/j.actamat.2018.12.01510.1016/j.actamat.2018.12.015 ↗
53. 10.1016/j.scriptamat.2019.11.05310.1016/j.scriptamat.2019.11.053 ↗
54. 10.1002/adem.20160025210.1002/adem.201600252 ↗
55. 10.1016/j.msea.2020.14010110.1016/j.msea.2020.140101 ↗
56. 10.1080/0950083080243812310.1080/09500830802438123 ↗
57. 10.1016/j.actamat.2018.02.03710.1016/j.actamat.2018.02.037 ↗
58. 10.1126/science.112426810.1126/science.1124268 ↗
59. 10.1002/adem.20190050710.1002/adem.201900507 ↗
60. 10.1002/adem.20180018410.1002/adem.201800184 ↗
61. 10.1016/j.msea.2017.07.02310.1016/j.msea.2017.07.023 ↗
62. 10.1016/j.scriptamat.2020.07.02710.1016/j.scriptamat.2020.07.027 ↗