journal article·2015-12Open access

Gradient Structure in High Pressure Torsion Compacted Iron Powder

Yajun Zhao, Roxane Massion, Thierry Grosdidier, Laszlo S. Toth

Advanced Engineering Materials· Volume 17· Issue 12

Abstract

Iron powder was compacted successfully into a solid disk by a severe plastic deformation process – the high pressure torsion (HPT) – at room temperature. The compaction was done in two steps: first axial compaction, then shear deformation by rotating the bottom part of the HPT die while maintaining the axial force constant. The homogeneity of shear strain across the thickness of the disk was examined by local strain measurement, showing a gradient distribution. The strain gradient leads to the formation of three regions throughout the thickness of the disk: Region U, that is undeformed in torsion (top part – in contact with the fixed punch), Region T, that is a transition or intermediate region where the shear strain is increasing, and Region S, which is severely deformed (bottom part – in contact with the rotating die) which is uniformly and heavily sheared. The observation of microstructure and Vickers hardness in the three regions showed a non‐uniform distribution, corresponding to the strain gradient. Crystallographic texture measurements confirmed the presence of a typical shear texture with increasing strength in Regions T and S. Stress–strain curve was obtained from the local shear strain and microhardness measurements. The strain hardening curve of the HPT‐compacted pure iron showed higher flow stress than the torsion deformed solid pure iron (IF steel).
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Powder Metallurgy Techniques and Materials · Microstructure and mechanical properties · Advanced materials and composites

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Laboratoire d'Etude des Microstructures et de Mécanique des Matériaux (LEM3) UMR 7239, CNRS/Université de Lorraine F‐57045 Metz France

Laboratory of Excellence on Design of Alloy Metals for Low‐mAss Structures (DAMAS) Université de Lorraine France

References (24)

Show source-provided references
1. 10.1016/0921-5093(95)09705-810.1016/0921-5093(95)09705-8 ↗
2. 10.1016/j.scriptamat.2004.05.00610.1016/j.scriptamat.2004.05.006 ↗
3. 10.1007/s11837-006-0213-710.1007/s11837-006-0213-7 ↗
4. 10.1016/S0079-6425(99)00007-910.1016/S0079-6425(99)00007-9 ↗
5. 10.1016/j.actamat.2009.06.01010.1016/j.actamat.2009.06.010 ↗
6. 10.1016/0965-9773(95)00077-110.1016/0965-9773(95)00077-1 ↗
7. 10.1016/j.scriptamat.2005.08.01210.1016/j.scriptamat.2005.08.012 ↗
8. 10.1088/1757-899X/63/1/01203210.1088/1757-899X/63/1/012032 ↗
9. 10.1016/j.mseb.2013.11.02510.1016/j.mseb.2013.11.025 ↗
10. 10.1016/j.scriptamat.2008.01.01010.1016/j.scriptamat.2008.01.010 ↗
11. 10.1016/S1359-6454(96)00156-510.1016/S1359-6454(96)00156-5 ↗
12. 10.1007/s10853-012-6507-y10.1007/s10853-012-6507-y ↗
13. 10.1016/S1003-6326(11)61390-310.1016/S1003-6326(11)61390-3 ↗
14. 10.1016/0001-6160(84)90050-610.1016/0001-6160(84)90050-6 ↗
15. J. J.Fundenberger B.Beausir Université de Lorraine‐Metz JTEX‐Software for Texture Analysis2015 http://jtex‐software.eu/
16. 10.1016/1359-6454(96)00114-010.1016/1359-6454(96)00114-0 ↗
17. 10.1088/0508-3443/7/5/30110.1088/0508-3443/7/5/301 ↗
18. 10.1016/j.scriptamat.2012.02.00410.1016/j.scriptamat.2012.02.004 ↗
19. 10.1002/adem.20031009010.1002/adem.200310090 ↗
20. 10.1016/j.scriptamat.2013.10.02010.1016/j.scriptamat.2013.10.020 ↗
21. B.Beausir EBSDmcf Software for Orientation Image Mapping 2011 http://www.benoitbeausir.eu/
22. A.Pougis Doctoral Thesis Université de Lorraine2013.
23. 10.1016/j.matlet.2004.07.02610.1016/j.matlet.2004.07.026 ↗
24. 10.1016/0965-9773(95)00089-510.1016/0965-9773(95)00089-5 ↗