Regulated final cold drawing facilitates preferential strength and cold forging of an Al–Zn–Mg–Cu alloy fastener wire
Bibliographic record
Abstract
No abstract is available for this record. The assistant can identify its topic from the title, but cannot infer the study’s results.
Source: Not provided · Quality: missing
Research context
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (61)
Show source-provided references
1. Localized corrosion damage morphology and corrosion electrochemistry for al-zn-mg-cu and stainless steel 316 fastener galvanic couples in simulated marine environments10.1149/MA2017-02/10/713 ↗
2. Nosing process of 2A12 aluminum alloy spacing shims for non-disengagement fastening devices for spacecrafts10.3390/met12081348 ↗
3. Heat treatment of 7xxx series aluminium alloys-some recent developments10.1016/S1003-6326(14)63306-9 ↗
4. Microstructure and mechanical properties of 7A56 aluminum alloy after solution treatment10.1007/s12598-017-0985-7 ↗
5. Aging behavior and precipitate characterization of a high Zn-containing Al-Zn-Mg-Cu alloy with various tempers10.1016/j.matdes.2016.03.150 ↗
6. Improving the microstructure and properties of a high-alloyed Al-Zn-Mg-Cu alloy by optimizing the initial temperature of pre-recovery multi-stage solution treatment (P-MST)10.1016/j.msea.2025.148357 ↗
7. The effect of combination of pre-ageing and regression heat treatment on the natural aging behavior in Al-Zn-Mg-Cu alloys correlated with precipitate dissolving ratio10.1016/j.jmrt.2024.07.018 ↗
8. Enhancing mechanical and corrosion properties of Al-Zn-Mg-Cu alloy through electropulsing and aging alternate treatment10.1016/j.matchar.2024.114485 ↗
9. Effect of Zn content and Sc、Zr addition on microstructure and mechanical properties of Al-Zn-Mg-Cu alloys10.1016/j.jallcom.2023.169246 ↗
10. Synergetic effect of natural ageing and pre-stretching on the ageing behavior in Tʹ/ηʹ phase-strengthened Al-Zn-Mg-Cu alloys10.1016/j.jmst.2022.10.074 ↗
11. Effect of ageing temperature on microstructure, mechanical property and corrosion behavior of aluminum alloy 708510.1016/j.jallcom.2020.153792 ↗
12. Effect of Sc on aging kinetics in a direct chill cast al-zn-mg-cu alloy10.1007/s11661-008-9485-6 ↗
13. The Al-Zn-Mg-Cu alloy based on maximum solubility constraint designing strengthened by ultra-fine MgZn2 precipitates exhibits ultra-high strength-ductility synergy10.1016/j.jallcom.2025.180946 ↗
14. Effect of multi-stage aging treatments on the precipitation and mechanical properties of Al-Zn-Mg alloys10.1016/j.msea.2020.139394 ↗
15. Microstructures and mechanical properties of al-zn-mg-cu alloys under multi-directional severe strain and aging10.3390/ma16124441 ↗
16. Microstructural evolution of AA7050 alloy wires during tandem hot rolling (THR) and cold-drawing process10.1016/j.msea.2022.143512 ↗
17. Fatigue strength and microstructure evaluation of Al 7050 alloy wires recycled by spray forming, extrusion and rotary swaging10.1016/S1003-6326(20)65454-1 ↗
18. Microstructure, mechanical properties and corrrosion behavior of Al-Zn-Mg-Cu wire under different annealing conditions10.1016/j.jmrt.2024.04.134 ↗
19. Solidification phases and their evolution during homogenization of a DC cast Al-8.35Zn-2.5Mg-2.25Cu alloy10.1016/j.matchar.2014.04.004 ↗
20. Effects of Mg contents on microstructures and second phases of as-cast Al-Zn-Mg-Cu alloys10.1016/j.jmrt.2022.10.050 ↗
21. An in-situ study on the dissolution of intermetallic compounds in the Al-Zn-Mg-Cu alloy10.1016/j.jallcom.2020.154612 ↗
22. Influence of minor Sc additions on grain refinement and microstructure characteristics of a high Zn-containing Al-Zn-Mg-Cu-Zr alloy10.1007/s11771-022-4979-8 ↗
23. Evolution of precipitate microstructures during the retrogression and re-ageing heat treatment of an Al-Zn-Mg-Cu alloy10.1016/j.actamat.2010.05.017 ↗
24. GP-zones in Al-Zn-Mg alloys and their role in artificial aging10.1016/S1359-6454(01)00251-8 ↗
25. Early-stage precipitation in Al-Zn-Mg-Cu alloy (7050)10.1016/j.actamat.2004.06.025 ↗
26. HREM study and structure modeling of the η′ phase, the hardening precipitates in commercial Al-Zn-Mg alloys10.1016/S1359-6454(99)00138-X ↗
27. Characterization of precipitates in an aged 7 xxx series Al alloy10.1002/sia.1702 ↗
28. Effects of Cu and Al on the crystal structure and composition of η (MgZn2) phase in over-aged Al-Zn-Mg-Cu alloys10.1007/s10853-012-6428-9 ↗
29. A comparative study of precipitate composition and volume fraction in an Al-Zn-Mg alloy using tomographic atom probe and small-angle X-ray scattering10.1080/01418610108217154 ↗
30. Kinetic Monte Carlo simulation of clustering in an Al-Zn-Mg-Cu alloy (7050)10.1016/j.actamat.2004.10.048 ↗
31. DTA investigation of the retrogression and re-ageing in some AlZnMgCu alloys10.1016/S0040-6031(97)00254-2 ↗
32. Quantitative study of precipitates in an Al-Zn-Mg-Cu alloy aged with various typical tempers10.1016/j.msea.2013.09.005 ↗
33. Effect of hot deformation on microstructure and quenching-induced precipitation behavior of Al-Zn-Mg-Cu alloy10.1016/j.matchar.2020.110861 ↗
34. Precipitation sequence in Al-Sc-Zr alloys revisited10.1016/j.mtla.2022.101608 ↗
35. Effects of critical defects on stress corrosion cracking of Al-Zn-Mg-Cu-Zr alloy10.1016/j.jmrt.2021.03.070 ↗
36. Effect of rapid cold stamping on microstructure and mechanical properties of spray-formed Al-Zn-Mg-Cu alloy10.1016/S1003-6326(25)66852-X ↗
37. Research status and prospective properties of the Al-Zn-Mg-Cu series aluminum alloys10.3390/met13081329 ↗
38. Dynamic recrystallization mechanisms and microstructure evolution of a novel Al-Zn-Mg-Cu-Zr alloy by isothermal compression10.1016/j.jmrt.2024.09.200 ↗
39. Multiscale analysis of grain boundary microstructure in high strength 7xxx Al alloys10.1016/j.actamat.2020.10.021 ↗
40. Effect of Zn content on the dynamic softening of Al-Zn-Mg-Cu alloys during hot compression deformation10.1016/j.vacuum.2020.109941 ↗
41. The relation between polycrystal deformation and single-crystal deformation10.1007/BF02900224 ↗
42. Design, evolution, formation and effect mechanism of coupling distributed soft and hard micro-regions in Al-Zn-Mg-Cu-Fe alloys with high formability10.1016/j.msea.2022.143951 ↗
43. Regulation of high-temperature microstructure evolution and recrystallization by pre-strain accumulation in Al-Zn-Mg-Cu alloys10.1016/j.jmrt.2025.07.085 ↗
44. Design and research on Al-Zn-Mg-Cu alloy with ultra-high strength and good plasticity matching
45. Recrystallization behavior of an Al-Zn-Mg-Cu alloy during hot deformation and subsequent heat treatment
46. Current issues in recrystallization: a review10.1016/S0921-5093(97)00424-3 ↗
47. Study on hot deformation behavior and dynamic recrystallization mechanism of recycled Al-Zn-Mg-Cu alloy10.1016/j.jmrt.2024.10.163 ↗
48. Plasticity of crystals with special reference to metals10.1088/0031-9112/20/3/024 ↗
49. A loading-dependent model of critical resolved shear stress10.1016/j.ijplas.2018.03.011 ↗
50. Mechanical properties
51. Influence of predeformation and agEing of an Al-Zn-Mg alloy-II. Modeling of precipitation kinetics and yield stress10.1016/S1359-6454(98)00296-1 ↗
52. A model for the yield strength of overaged Al-Zn-Mg-Cu alloys10.1016/S1359-6454(03)00363-X ↗
53. The deformation and ageing of mild steel10.1088/0370-1301/64/6/305 ↗
54. High-resolution characterization of the precipitation behavior of an Al-Zn-Mg-Cu alloy10.1080/09500839.2011.652682 ↗
55. Strengthening mechanisms in a high-strength bulk nanostructured Cu-Zn-Al alloy processed via cryomilling and spark plasma sintering10.1016/j.actamat.2012.09.036 ↗
56. Work hardening due to internal stresses in composite materials10.1016/0001-6160(75)90198-4 ↗
57. Experimental and DFT characterization of η′ nano-phase and its interfaces in Al Zn Mg Cu alloys10.1016/j.actamat.2018.10.045 ↗
58. Effect of various retrogression regimes on aging behavior and precipitates characterization of a high Zn-Containing al-zn-mg-cu alloy10.1007/s12540-018-0077-8 ↗
59. Mechanical behavior and strengthening mechanisms in ultrafine grain precipitation-strengthened aluminum alloy10.1016/j.actamat.2013.09.042 ↗
60. Modeling of GP(I) zone formation during quench in an industrial AA7449 75 mm thick plate10.1016/j.matdes.2016.09.052 ↗
61. Revealing the strengthening mechanisms in Al-Zn-Mg-Cu alloys with multiple types of precipitates: experiment and theoretical model10.1016/j.msea.2025.148065 ↗