Influence of loading rate on the nanoindentation creep behavior of BOPA6 film
Source abstract
Abstract
In this study, the influence of the loading rate on the room-temperature creep behavior of biaxially oriented polyamide-6 (BOPA6) films were investigated via nanoindentation. It was found that strongly dependence of the creep deformation on the loading-rate: significant creep deformation occurred at loading rates between 1 and 10 mN/s, whereas it gradually diminishes as the loading rate decreases and nearly disappears at rates of 1 mN/s. Moreover, the experimental creep response was successfully fitted by using an Extended Variable-Order Elastic Viscoelastic (EVEV) model, which demonstrated high correlation with the measured data (R 2 > 0.99), and the creep compliance and retardation spectrum related to the internal structure of BOPA6 films were derived. The creep rate-sensitivity index ( m ) correlated positively with the loading rate, suggesting that the viscoelastic response of BOPA6 films become increasingly sensitive under the faster loading rate. These results provide a basis for a detailed discussion of the underlying room-temperature creep mechanisms in BOPA6 films.
Source: crossref · Quality: baseline
Research context
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Hunan University of Technology
Funding
The Natural Science Foundation of Hunan Province · The National Key R&D Program of China · The Hunan Provincial Education Department · The National Natural Science Foundation of China
References (32)
Show source-provided references
1. 10.1080/25740881.2022.213361710.1080/25740881.2022.2133617 ↗
2. Sohanaki P, Ahamadloo E, Gharehaghaji AA, et al. Fabrication and characterization of three-layer nanofibrous yarn (PA6/PU/PA6). Polym Bull 2021; 79: 1–20. https://doi.org/10.1007/s00289-021-03835-2
3. 10.1002/pat.549710.1002/pat.5497 ↗
4. 10.1515/rams-2022-033210.1515/rams-2022-0332 ↗
5. 10.1016/j.jksues.2020.09.00310.1016/j.jksues.2020.09.003 ↗
6. 10.1021/acssuschemeng.0c0419010.1021/acssuschemeng.0c04190 ↗
7. 10.1016/j.mseb.2020.11460510.1016/j.mseb.2020.114605 ↗
8. 10.3390/polym1607096110.3390/polym16070961 ↗
9. 10.1007/s00289-022-04199-x10.1007/s00289-022-04199-x ↗
10. 10.3390/polym1704044210.3390/polym17040442 ↗
11. 10.1002/pen.2590510.1002/pen.25905 ↗
12. 10.3139/217.384910.3139/217.3849 ↗
13. 10.1029/2021JB02222910.1029/2021JB022229 ↗
14. 10.1557/s43578-021-00173-x10.1557/s43578-021-00173-x ↗
15. 10.1016/j.polymertesting.2020.10697810.1016/j.polymertesting.2020.106978 ↗
16. 10.1016/j.polymertesting.2020.10635310.1016/j.polymertesting.2020.106353 ↗
17. Khan S, Khadija JM, et al. Evaluations of nanomechanical and indentation creep of diffusion-bonded aluminum and austenitic stainless steel joint interface. Proc Inst Mech Eng Part L 2025; 239: 1353–1365. https://doi.org/10.1177/14644207241290447
18. 10.1016/j.polymer.2024.12707810.1016/j.polymer.2024.127078 ↗
19. 10.1016/j.matdes.2025.11400810.1016/j.matdes.2025.114008 ↗
20. 10.1016/j.polymertesting.2025.10892310.1016/j.polymertesting.2025.108923 ↗
21. 10.1007/s40948-020-00178-610.1007/s40948-020-00178-6 ↗
22. 10.3390/polym1414294510.3390/polym14142945 ↗
23. 10.3390/coatings1009084610.3390/coatings10090846 ↗
24. 10.1016/j.apm.2023.05.01710.1016/j.apm.2023.05.017 ↗
25. 10.1063/1.165134110.1063/1.1651341 ↗
26. 10.7498/aps.58.405910.7498/aps.58.4059 ↗
27. 10.3390/polym1719265110.3390/polym17192651 ↗
28. 10.1016/S0257-8972(00)01063-X10.1016/S0257-8972(00)01063-X ↗
29. Khan S, Junaid M, Khan FN. Nanoindentation and indentation creep analysis of diffusion bonded of inconel 718 and AISI 304L stainless steel joint interface. Proc Inst Mech Eng Part L 2025; 239: 1620–1632. https://doi.org/10.1177/14644207241301338
30. 10.1016/j.ijmecsci.2018.02.03510.1016/j.ijmecsci.2018.02.035 ↗
31. 10.1007/s11440-013-0269-910.1007/s11440-013-0269-9 ↗
32. 10.1557/PROC-1049-AA10-0210.1557/PROC-1049-AA10-02 ↗