journal article·2023-12

Implications of cryogenic treatment on microstructure, phase formation, mechanical and tribological properties of tungsten carbide cutting bits with varying cobalt content for mining applications

Moganapriya Chinnasamy, Rajasekar Rathanasamy, Biswajit Samanta, Samir Kumar Pal, Sathish Kumar Palaniappan, Padmakumar Muthuswamy, Roja Rani Korrayi, Shibayan Roy

Publisher page

Abstract

This study aims to provide a comprehensive analysis on the effect of cryogenic treatment on two different grades of WC rock cutting bits (low cobalt grade: WC-9 wt% Co and high cobalt grade: WC-25 wt% Co). The cutting bits are exposed to cryogenic treatment at different holding time such as 12, 24 and 36 h. The treated and untreated bits are characterized for low temperature DSC, phase analysis, microstructural study, elemental composition, hardness, fracture toughness and scratch test. Phase shift was observed for both the cases due to the martensitic phase transformation from α-Co (fcc) to ε Co (hcp) during cryogenic treatment. This transition was confirmed with low temperature DSC analysis between −90 °C and − 60 °C. New η carbide particles (Co 6W 6 C) was formed for WC-25%Co and no such carbides was found for WC-9%Co. CT 36 of WC-25%Co exhibited a higher level of precipitation of η carbides. The results show that CT has enhanced hardness for both low (14.08%) and high cobalt (23.34%) WC cutting bits compared to untreated bits whereas density is not altered evidently. CT 24 and CT 36 possessed higher hardness and lower fracture toughness for WC-9%Co and WC-25%Co respectively. Higher CoF and formation of tribo layer was observed for treated bits whereas untreated bit experiences surface fracture and cracks as a result of scratch test. As a finding, mining sectors can utilize cutting bits that have undergone sustainable cryogenic treatment for rock cutting applications.
Source: expertdata · Quality: candidate unverified · Source record ↗

References (49)

Show source-provided references
1. Effect of cryogenic treatment on WC–co cemented carbides10.1016/j.msea.2010.11.009 ↗
2. Microstructural transformation analysis of cryogenic treated conical rock cutting bits for mining applications10.1016/j.ijrmhm.2022.105995 ↗
3. Cryogenic treatment to augment wear resistance of tool and die steels10.1016/S0011-2275(01)00065-0 ↗
4. Toughening optimization on a low carbon steel by a novel quenching-partitioning-cryogenic-tempering treatment10.1016/j.msea.2018.04.104 ↗
5. Machinability of C45 steel with deep cryogenic treated tungsten carbide cutting tool inserts10.1016/j.ijrmhm.2008.04.007 ↗
6. Effect of cryogenic treatment on dimensional stability and hardness of 20CrMnTi steel
7. Zhang · 2014
8. Investigating the effect of quench environment and deep cryogenic treatment on the wear behavior of AZ9110.1016/j.matdes.2013.07.051 ↗
9. Microstructure evolution in metastable β titanium alloy subjected to deep cryogenic treatment10.1016/j.msea.2018.03.003 ↗
10. Effect of deep cryogenic treatment on the fracture toughness and wear resistance of WC-co cemented carbides10.1016/j.ijrmhm.2019.105059 ↗
11. Performance of cryogenically treated tungsten carbide tools in milling operations10.1007/s00170-005-0379-0 ↗
12. Metallurgical and mechanical characteristics of cryogenically treated tungsten carbide (WC–co)10.1007/s00170-011-3369-4 ↗
13. Investigation on the performance of deep and shallow cryogenic treated tungsten carbide drills in austenitic stainless steel10.1016/j.measurement.2018.05.018 ↗
14. Influence of deep cryogenic treatment on performance of cemented carbide (WC-co) inserts during dry end milling of maraging steel10.1016/j.jmapro.2018.11.030 ↗
15. An investigation of cobalt phase structure in WC–co cemented carbides before and after deep cryogenic treatment10.1016/j.ijrmhm.2015.04.007 ↗
16. Investigation of phase structure of cobalt and its effect in WC–co cemented carbides before and after deep cryogenic treatment10.1016/j.ijrmhm.2018.03.010 ↗
17. Effects of deep cryogenic treatment on microstructure and properties of WC–11Co cemented carbides with various carbon contents10.1016/S1003-6326(15)63929-2 ↗
18. Microstructural and Tribological characterization of cryogenic treated WC-co cutting bits under different holding times for rock cutting applications
19. Machining performance of low temperature treated P-30 tungsten carbide cutting tool inserts10.1016/j.cryogenics.2008.06.001 ↗
20. Effect of cutting conditions on wear performance of cryogenically treated tungsten carbide inserts in dry turning of stainless steel10.1016/j.triboint.2015.08.024 ↗
21. Effects of deep cryogenic treatment for tungsten carbide-iron cemented carbide10.1016/j.ijrmhm.2021.105649 ↗
22. Influence of different post treatments on microstructure and properties of WC-co cemented carbides10.1016/j.jallcom.2014.09.100 ↗
23. The influence of cryogenic-aging circular treatment on the microstructure and properties of aluminum matrix composites10.1016/j.jallcom.2016.11.028 ↗
24. Fracture toughness of cemented carbides: testing method and microstructural effects10.1016/j.ijrmhm.2014.08.018 ↗
25. Microstructure and properties of coarse-grained WC–10Co cemented carbides with different carbon contents during heat treatments
26. Comparative investigations of cryo-treated and untreated inserts on machinability of AISI 1050 by using response surface methodology, ANOVA and Taguchi design10.1177/09544062211023117 ↗
27. Effectiveness of cryogenic treatment on cutting tool inserts: a review10.1016/j.ijrmhm.2022.105946 ↗
28. Kinetics of the allotropic hcp–fcc phase transformation in cobalt10.1080/14786435.2010.525541 ↗
29. Binder phase strengthening of WC–co alloy through post-sintering treatment10.1016/j.ijrmhm.2014.09.031 ↗
30. Effects of deep cryogenic treatment on the microstructure and mechanical properties of an ultrahigh-strength TRIP-aided bainitic steel10.1016/j.matchar.2021.111247 ↗
31. Improvement in performance of cryogenically treated tungsten carbide tools in face milling of Ti-6Al-4V alloy10.1080/10426914.2019.1615079 ↗
32. Influence of different post treatments on tungsten carbide–cobalt inserts10.1016/j.matlet.2008.07.043 ↗
33. Characterization of the mechanism of cryogenic treatment on the microstructural changes in tungsten carbide cutting tools10.1016/j.matchar.2019.02.006 ↗
34. Metallurgy behind the cryogenic treatment of cutting tools: an overview
35. Experimental investigations and performance analysis in turning of nodular cast iron using cryogenically treated tungsten carbide inserts
36. Machinability of C45 steel with deep cryogenic treated tungsten carbide cutting tool inserts10.1016/j.ijrmhm.2008.04.007 ↗
37. Performance evaluation of cryogenically treated tungsten carbide cutting tool inserts10.1243/095440503762502260 ↗
38. Flank wear and machining performance of cryogenically treated tungsten carbide inserts10.1080/10426914.2011.557128 ↗
39. Effect of deep cryogenic treatment on machinability and wear mechanism of TiAlN coated tools during dry turning10.1007/s12541-014-0384-z ↗
40. Morphology of WC grains in WC–co alloys10.1016/j.msea.2007.09.019 ↗
41. Variation of WC grain shape with carbon content in the WC–co alloys during liquid-phase sintering10.1016/S1359-6462(02)00464-5 ↗
42. Microstructure evolution, phase formation, mechanical and tribological response of deep cryogenically treated hard WC-6%Co cutting bits10.1016/j.jmrt.2023.09.320 ↗
43. Cryoprocessing of cutting tool materials—a review10.1007/s00170-009-2263-9 ↗
44. Metallurgical and mechanical characteristics of cryogenically treated tungsten carbide (WC–co)10.1007/s00170-011-3369-4 ↗
45. Influence of cryo-processing on properties of tungsten carbide with low, medium and high cobalt content10.1088/2053-1591/ab3c97 ↗
46. Investigating the effect of holding duration on the microstructure of 1.2080 tool steel during the deep cryogenic heat treatment10.1016/j.vacuum.2012.02.013 ↗
47. Bal · 2012
48. Effects of WC particle size on densification and properties of spark plasma sintered WC–co cermet10.1016/j.ijrmhm.2009.07.017 ↗
49. Tribofilm formation on cemented carbides in dry sliding conformal contact10.1016/S0043-1648(00)00315-X ↗