Effect of grain size and cobalt content on machining performance during milling tungsten carbide with PCD tool
Source abstract
Abstract
Tungsten carbide has been extensively utilized in the manufacturing field due to its exceptional properties. However, traditional methods such as grinding or electric discharge machining often result in a low material removal rate and inevitable surface defects, making tungsten carbide one of the most challenging materials to machine. Milling has emerged as a promising alternative for machining tungsten carbide. However, the milling of tungsten carbide has not been widely applied in the industry due to a lack of comprehensive understanding regarding the milling performance of different tungsten carbides under various conditions. In this paper, a polycrystalline diamond (PCD) tool was used in the milling of tungsten carbides to investigate the effects of tool grain size, workpiece Co content, and WC grain size on tool wear and machining surface quality. It was found that PCD tools with larger grain sizes exhibited higher wear resistance. Additionally, excessive Co content in the workpiece and large WC grain size increased tool wear and degraded the quality of the machined surface. The primary types of tool wear observed in the milling of WC-Co included adhesive wear, abrasive wear, phase change wear, and oxidation wear.
Source: expertdata · Quality: candidate unverified · Source record ↗
References (38)
Show source-provided references
1. Ultrafine/nano WC-Co cemented carbide: overview of preparation and key technologies10.1016/j.jmrt.2023.10.315 ↗
2. Experimental investigation on the problems in the achievement of super-smooth surface of cemented carbide WC-Co through diamond turning10.1016/j.ijrmhm.2023.106461 ↗
3. Influence of sintering parameters on the microstructure and mechanical properties of WC-Co hardmetals10.1016/j.ijrmhm.2023.106439 ↗
4. Size and speed of ejected particles from different cemented carbide grades machined with sinking EDM10.1016/j.procir.2022.09.148 ↗
5. In-situ laser-assisted ultraprecision cutting of WC-co cemented carbide for creating microstructure arrays10.1016/j.ceramint.2023.09.206 ↗
6. Fabrication of PCD face grinding wheel with positive rake angle by femtosecond laser and its performance evaluation in cemented carbide grinding10.1016/j.diamond.2023.110418 ↗
7. Electrochemical machining of cemented carbides10.1016/j.ijrmhm.2014.06.010 ↗
8. Effect of heat treatment on microstructural evolution and properties of cemented carbides (WC-17Co) reinforced with 3% volume hexagonal-boron nitride (h-BN) and processed by selective laser sintering (SLS)10.1016/j.matchar.2021.110968 ↗
9. Discharge energy based optimisation of sinking EDM of cemented carbides10.1016/j.procir.2022.03.113 ↗
10. A comprehensive review on the cutting and abrasive machining of cemented carbide materials10.1016/j.jmapro.2023.10.042 ↗
11. Analysis of the electrochemical behaviors of WC–Co alloy for micro ECM10.1016/j.jmatprotec.2012.10.018 ↗
12. Origin of superhard pure PcBN: a relation to the fragment and its plastic mechanism under the high pressure10.1016/j.ceramint.2022.10.269 ↗
13. Cutting performance and wear behavior of diamond, coated cemented carbide and PCBN tools during milling of Cf/SiC composites10.1016/j.diamond.2023.110473 ↗
14. Surface quality of cemented tungsten carbide finished by direct cutting using diamond-coated carbide end mill10.1016/j.jmapro.2020.11.004 ↗
15. HPC-milling of WC-Co cemented carbides with PCD10.1016/j.ijrmhm.2017.12.019 ↗
16. Experimental investigation on direct micro milling of cemented carbide10.3390/mi10020147 ↗
17. Fabrication of PCD micro end mill for machining hard and brittle material10.1007/s00170-019-03343-8 ↗
18. Internal turning of sintered carbide parts: tool wear and surface roughness evaluation10.1007/s40430-018-1139-z ↗
19. Coppini · 2013 · vol. 8 · 368
20. Suppression of diamond tool wear in machining of tungsten carbide by combining ultrasonic vibration and electrochemical processing10.1016/j.ceramint.2017.11.215 ↗
21. An experimental study on milling of high-volume fraction SiCP/Al composites with PCD tools of different grain size10.1007/s00170-015-6901-0 ↗
22. Influence of WC and co contents in cutting of wear and impact resistant cemented carbides10.1299/jsmec.49.90 ↗
23. Study on wear behaviors and grain effects of PCD cutting tools in turning granite10.4028/www.scientific.net/AMM.214.130 ↗
24. Study on characteristics in high-speed milling SiCp/Al composites with small particles and high volume fraction by adopting PCD cutters with different grain sizes10.1007/s00170-019-03374-1 ↗
25. Milling of high volume fraction SiCp/Al composites using PCD tools with different structures of tool edges and grain sizes10.1007/s00170-017-0297-y ↗
26. Influence of WC and Co in cutting cemented carbides with PCD and CBN tools10.4028/www.scientific.net/KEM.407-408.428 ↗
27. Environmentally conscious hard turning of cemented carbide materials on the basis of micro-cutting in SEM: stressing four kinds of cemented carbides with PCD tools10.1007/s12206-008-0411-z ↗
28. Estimating the effect of cutting data on surface roughness and cutting force during WC-Co turning with PCD tool using Taguchi design and ANOVA analysis10.1007/s00170-014-6382-6 ↗
29. Experimental investigations on the machinability of tungsten carbides in orthogonal cutting with diamond-coated tools10.1016/j.procir.2016.04.008 ↗
30. Influence of cutting parameters on PCD tool wear during milling tungsten carbide10.1007/s00170-023-12775-2 ↗
31. Fracture propagation in brittle granular matter
32. Grain size dependence of tensile properties in nanocrystalline diamond10.1016/j.commatsci.2018.10.027 ↗
33. Performance and wear mechanisms of polycrystalline diamond tools with different diamond grains in milling Cf/SiC composites10.1016/j.wear.2024.205355 ↗
34. Effects of carbothermal prereduction temperature and co content on mechanical properties of WC–Co cemented carbides10.1111/ijac.14383 ↗
35. Effect of co content on microstructure and mechanical properties of ultrafine grained WC-Co cemented carbide sintered by spark plasma sintering10.1016/j.ceramint.2018.07.100 ↗
36. Microstructure and properties of ultrafine cemented carbides—differences in spark plasma sintering and sinter-HIP10.1016/j.msea.2012.05.065 ↗
37. Molecular dynamics simulation on friction and wear behavior of WC-Co cemented carbides
38. Cemented carbide microstructures: a review10.1016/j.ijrmhm.2018.12.004 ↗