Study on the microstructure and properties of WCu alloy foils prepared by cyclic warm rolling
Source abstract
Abstract
The initial production of a W30Cu foil with a thickness of 0.1 mm and high relative density (99.9 %), as well as excellent physical and mechanical properties, was achieved through the utilisation of hot-press sintering (HPS) in conjunction with cyclic warm rolling. The impact of rolling deformation on the microstructure and overall performance of the composite material was examined, and the coordinated deformation mechanisms occurring during the rolling process were investigated. As the reduction rate increased, the deformation mechanism of the W30Cu composite material shifted from a Cu-phase-dominated plastic deformation to a cooperative deformation involving both the Cu and W phases. The number of high-angle grain boundaries (HAGBs) increased gradually with the occurrence of dynamic recrystallisation, accompanied by an expansion in the thickness of the W/Cu interface diffusion layer. The yield strength and tensile strength exhibited a gradual increase during the cyclic warm rolling process, while the coefficient of thermal expansion (CTE), electrical conductivity (EC) and thermal conductivity (TC) demonstrated a gradual decrease. Upon reaching an accumulated reduction rate of R98% (0.1 mm), the yield strength of the W30Cu composite material reached 767 MPa, the tensile strength reached 887 MPa, and the CTE, EC and TC were 210 W/(m·K), 40.8 % IACS and 6.2 × 10 −6/K, respectively.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (60)
Show source-provided references
1. Microstructure and properties characterization of tungsten–copper composite materials doped with graphene[J]10.1016/j.jallcom.2016.10.310 ↗
2. Experimental and prediction of sintered cu–W composite by using artificial neural networks[J]10.1016/j.matdes.2012.08.056 ↗
3. Progress in research on hybrid metal matrix composites[J]10.1016/j.jallcom.2020.155274 ↗
4. Low-temperature densification and excellent thermal properties of W–Cu thermal-management composites prepared from copper-coated tungsten powders[J]10.1016/j.jallcom.2013.11.003 ↗
5. Progress, challenges and potentials/trends of tungsten-copper (WCu) composites/pseudo-alloys: fabrication, regulation and application[J]10.1016/j.ijrmhm.2021.105648 ↗
6. Three-dimensional characterization of the permeability of W–Cu composites using a new “TriBeam” technique[J]10.1016/j.actamat.2013.10.043 ↗
7. Engineered chemistry of cu–W composites sintered by field-assisted sintering technology for heat sink applications[J]10.1007/s10853-010-4842-4 ↗
8. W–Cu composites with submicron-and nanostructures: progress and challenges[J]10.1038/s41427-019-0179-x ↗
9. Interfacial design of cu/SiC composites prepared by powder metallurgy for heat sink applications[J]10.1016/j.compositesa.2007.08.012 ↗
10. Recent progress in development of tungsten-copper composites: fabrication, modification and applications[J]10.1016/j.ijrmhm.2018.03.014 ↗
11. Mechanochemical synthesis of W–Cu nanocomposites via in-situ co-reduction of the oxides[J]10.1016/j.powtec.2012.08.013 ↗
12. Effect of processing route on densification of W-10 wt% cu nanocomposite using spark plasma sintering[J]10.1016/j.jallcom.2019.01.274 ↗
13. In-situ synthesis of core-shell structure W (WC) composite grains in W-cu composites fabricated by infiltration[J]10.1016/j.jallcom.2021.158633 ↗
14. Investigation on wear mechanism of thermochemically fabricated W–Cu composites[J]10.1016/j.wear.2010.04.026 ↗
15. Enhanced liquid-phase sintering of W–Cu composites by liquid infiltration[J]10.1016/j.ijrmhm.2013.12.004 ↗
16. A new process for fabricating W–15 wt.% cu sheet by sintering, cold rolling and re-sintering[J]10.1016/j.ijrmhm.2009.09.004 ↗
17. Tungsten/copper composite sheets prepared by a novel encapsulation rolling technique[J]10.1016/j.jallcom.2021.161051 ↗
18. Ultra-rapid processing of high-hardness tungsten–copper nanocomposites[J]10.1016/j.scriptamat.2015.11.012 ↗
19. Research on the densification of W-30 wt% cu composite powder by hot extrusion with steel cup[J]10.1016/j.msea.2013.04.082 ↗
20. The routes and mechanism of plasma facing tungsten materials to improve ductility[J]
21. Simultaneous optimization of the tensile strength, bending strength, hardness and wear resistance of WCu composite produced by sintering process[J]10.1016/j.ijrmhm.2023.106430 ↗
22. Microstructure and high-temperature mechanical properties of cu-W composite prepared by hot isostatic pressing[J]10.1016/j.jallcom.2023.172571 ↗
23. Significant lattice-distortion effect on compressive deformation in Mo-added CoCrFeNi-based high-entropy alloys[J]10.1016/j.msea.2021.142295 ↗
24. Microstructure and mechanical properties of Al–3Mg–0.25 Sc alloy sheets produced by cryorolling[J]10.1016/j.msea.2018.10.044 ↗
25. Evaluation of the intergranular crack growth resistance of ultrafine grained tungsten materials[J]10.1016/j.actamat.2019.06.051 ↗
26. Microstructure evolution of annealed 7075 aluminum alloy and its influence on room-temperature plasticity[J]10.1016/j.matdes.2020.109192 ↗
27. Effect and mechanism of room temperature rolling, cryogenic rolling and heat treatment on mechanical properties and electrical conductivity of cu-Ni-Si alloy with continuous directional solidification[J]10.1016/j.jallcom.2023.169748 ↗
28. Mo70Cu30 composites synthesized by infiltration sintering and hot rolling with simultaneously improved mechanical and electrical properties[J]10.1016/j.jallcom.2023.173156 ↗
29. The deformation of plastically non-homogeneous materials[J]10.1080/14786437008238426 ↗
30. Mechanism-based strain gradient plasticity—I. Theory[J]10.1016/S0022-5096(98)00103-3 ↗
31. Heterostructured metallic materials: plastic deformation and strain hardening
32. Recrystallization behavior of hot-rolled pure tungsten and its alloy plates during high-temperature annealing[J]10.1016/j.nme.2018.04.004 ↗
33. Evolution of microstructure and texture in a warm-rolled yttria dispersion-strengthened tungsten plate during annealing in the temperature range between 1200° C and 1350° C[J]10.1016/j.jallcom.2021.160767 ↗
34. Microstructure, mechanical and thermo-physical properties of hot-rolled Mo-50Cu composite[J]10.1016/j.jallcom.2023.168997 ↗
35. Effect of cross rolling on the edge microstructure and formability of AZ31B magnesium alloy[J]
36. Temperature and deformation effect on the low and high angle grain boundary structure of a double forged pure tungsten[J]10.1016/j.ijrmhm.2015.01.008 ↗
37. Microstructure and texture evolution in cold-rolled W during annealing[J]10.1016/j.ijrmhm.2024.106792 ↗
38. Cold rolled tungsten (W) plates and foils: evolution of the microstructure[J]10.1016/j.ijrmhm.2016.06.020 ↗
39. The brittle-to-ductile transition in cold rolled tungsten plates: impact of crystallographic texture, grain size and dislocation density on the transition temperature[J]10.1016/j.ijrmhm.2018.09.010 ↗
40. Ductilisation of tungsten (W): on the increase of strength AND room-temperature tensile ductility through cold-rolling[J]10.1016/j.ijrmhm.2016.10.018 ↗
41. Cube texture in hot-rolled aluminum alloy 1050 (AA1050)—nucleation and growth behavior[J]10.1016/j.actamat.2008.02.037 ↗
42. Direct diffusion bonding of immiscible tungsten and copper at temperature close to Copper’s melting point[J]10.1016/j.matdes.2017.10.052 ↗
43. Diffusion behavior of W in the WCu/Ni interface[J]10.1016/j.ijrmhm.2010.09.009 ↗
44. Diffusion behavior determined by the new n-body potential in highly immiscible W/cu system through molecular dynamics simulations[J]10.1016/j.jmrt.2023.04.068 ↗
45. Effect of Fe on the constitution of cu–W alloys at 1200° C[J]10.1016/S0925-8388(03)00434-1 ↗
46. Sintering behavior of molybdenum-copper and tungsten-copper alloys by using ultrafine molybdenum and tungsten powders as raw materials[J]10.1016/j.ijrmhm.2020.105194 ↗
47. Fracture behaviour of polycrystalline tungsten[J]10.1016/j.jnucmat.2013.11.001 ↗
48. The thermo-mechanical behaviour of W-cu metal matrix composites for fusion heat sink applications: the influence of the cu content[J]10.1016/j.jnucmat.2017.08.020 ↗
49. Infiltration sintering of WCu alloys from copper-coated tungsten composite powders for superior mechanical properties and arc-ablation resistance[J]10.1016/j.jallcom.2017.08.164 ↗
50. Low thermal expansion metal composite-based heat spreader for high temperature thermal management[J]10.1016/j.matdes.2021.109897 ↗
51. Microstructure and properties of WCu composites with low copper content at different sintering temperatures[J]10.1016/j.ijrmhm.2023.106219 ↗
52. Amorphous Thickness-Dependent Strengthening–Softening Transition in Crystalline–Amorphous Nanocomposites[J]10.1021/acs.nanolett.3c03848 ↗
53. Enhanced mechanical and electrical properties of in situ synthesized nano-tungsten dispersion-strengthened copper alloy[J]10.1016/j.msea.2020.140161 ↗
54. The deformation and ageing of mild steel: II characteristics of the Lüders deformation[J]10.1088/0370-1301/64/9/302 ↗
55. Fracture characteristics and heat treatment of laser powder bed fusion additively manufactured GRCop-84 copper[J]10.1016/j.msea.2021.141690 ↗
56. Preparation and properties of excellent performance W–Cu alloy with a variety of strengthening mechanisms[J]10.1016/j.msea.2023.145955 ↗
57. The calculation of thermal conductivity, viscosity and thermodynamic properties for nanofluids on the basis of statistical nanomechanics[J]10.1016/j.ijheatmasstransfer.2007.01.064 ↗
58. Texture evolution and basic thermal–mechanical properties of pure tungsten under various rolling reductions[J]10.1016/j.jnucmat.2015.04.001 ↗
59. Effect of interface modification by cu-coated W powders on the microstructure evolution and properties improvement for cu–W composites[J]10.1016/j.surfcoat.2016.01.014 ↗
60. Multilayered W–Cu composites with enhanced strength, electrical conductivity and wear resistance[J]10.1016/j.compositesb.2024.111641 ↗