Structure and wear performance of the atmospheric heat-treated HVOF sprayed bimodal WC-co coating
Source abstract
Abstract
Abstract In this study, the bimodal WC-Co coatings were prepared by high-velocity oxygen-fuel (HVOF). The coatings were then heat treated for 4 h at 350 °C, 450 °C and 550 °C in air atmosphere. The effect of the heat treatment on the composition, microstructure, mechanical property and wear performance were investigated. The results show that, after heat treatment, the coating shows dense microstructure at 450 °C and shows loose structure and cracks at 550 °C. the hardness first increases and then decreases with the increase of the heat-treated temperature, the maximum hardness is 1261 ± 61 HV after heat treatment at 450 °C. Testing at room and high temperature, the coating heat-treated at 450 °C for 4 h exhibits better wear resistance than the as-sprayed coating. The CoWO4 exhibits low shear strength and antifriction property and the friction promotes the formation of CoWO4.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (26)
Show source-provided references
1. Microstructure-property relations in WC-co coatings sprayed from combinatorial Ni-plated and nanostructured powders10.1016/j.matchar.2017.05.005 ↗
2. Improving the wear resistance of HVOF sprayed WC-co coatings by adding submicron-sized WC particles at the splats' interfaces10.1016/j.surfcoat.2015.11.017 ↗
3. Mechanical property and wear performance dependence on processing condition for cold-sprayed WC-(nanoWC-co)10.1016/j.apsusc.2015.01.138 ↗
4. Corrosion and strength degradation behaviors of binderless WC material and WC–co hardmetal in alkaline solution: a comparative investigation10.1016/j.ijrmhm.2017.06.003 ↗
5. Enhancement in the corrosion resistance of WC coatings by adding a Fe-based alloy in simulated seawater10.1016/j.surfcoat.2016.08.009 ↗
6. Relationships between feedstock structure, particle parameter, coating deposition, microstructure and properties for thermally sprayed conventional and nanostructured WC–co10.1016/j.ijrmhm.2012.03.014 ↗
7. New perspectives in hardmetal abrasion simulation10.1016/j.wear.2017.01.038 ↗
8. Improvement in tribological properties of atmospheric plasma-sprayed WC–co coating followed by cu electrochemical impregnation10.1016/j.apsusc.2009.04.181 ↗
9. Influence of heat treatment on the strength and fracture toughness of 7N01 aluminum alloy10.1016/j.jallcom.2016.03.228 ↗
10. Effect of Cr and Mn addition and heat treatment on AlSi3Mg casting alloy10.1016/j.matchar.2016.11.022 ↗
11. Effects of microstructure and heat treatment on mechanical properties and corrosion behavior of powder metallurgy derived Fe-30Mn alloy10.1016/j.msea.2017.07.054 ↗
12. Influence of heat treatment on the microstructure and performance of high-velocity oxy-fuel sprayed WC–12Co coatings10.1016/j.surfcoat.2012.03.080 ↗
13. Influence of heat treatment on the abrasive wear behaviour of HVOF sprayed WC–co coatings10.1016/S0257-8972(98)00444-7 ↗
14. Comparative tribological study of air plasma sprayed WC–12%co coating versus conventional hard chromium electrodeposit10.1016/j.triboint.2009.12.049 ↗
15. Formation of an amorphous phase in thermally sprayed WC-co10.1007/BF02647520 ↗
16. Microstructure and wear performance of heat treated WC-12Co microwave clad10.1016/j.vacuum.2016.06.021 ↗
17. Microstructural stability of thermal shayed WC-co composite coatings in oxidising atmospheres at 450°C10.1179/sur.1998.14.2.124 ↗
18. Structural and oxidation behavior of atmospheric heat treated plasma sprayed WC–co coatings10.1016/j.vacuum.2013.01.019 ↗
19. The oxidation of tungsten carbide10.1021/ja01622a023 ↗
20. Oxidation behavior of WC-co10.1016/0921-5093(95)10145-4 ↗
21. Weibull distribution of micro-hardness of plasma sprayed nanostructured ceramic coating and relation between phase composition and micro-hardness
22. The effect of temperature on the dry sliding wear behavior of HVOF sprayed nanostructured WC-CoCr coatings10.1016/j.ceramint.2016.09.180 ↗
23. Influences of the compositions and mechanical properties of HVOF sprayed bimodal WC-co coating on its high temperature wear performance10.1016/j.ijrmhm.2017.08.012 ↗
24. A crystal chemical approach to the formulation of self-lubricating nanocomposite coatings10.1016/j.surfcoat.2005.08.054 ↗
25. Wear behaviour of WC–co HVOF coatings at different temperatures in air and argon10.1016/j.wear.2015.01.035 ↗
26. A crystal-chemical approach to lubrication by solid oxides10.1023/A:1019183101329 ↗