Effect of plastic bending on high temperature creep resistance of molybdenum single crystals
Source abstract
Abstract
Abstract Using molybdenum single crystals, it is shown how plastic bending multiplies the high-temperature strength of products for pipelines and tube shells of small diameter (10–30 mm), which are subjected to high internal pressure. It is very convenient to do this when the plastic bending process is included in the manufacturing technology of such products, for example, in the form of spiral winding a strip into a pipe. It has been established that during 1000 h, the creep rate of a pre-bent Mo single crystals at 1633 K and an applied stress of 10 MPa permanently decreases by 4–5 orders of magnitude as compared to an unstrengthened single crystal. Using light microscopy, X-ray diffractometry, and transmission electron microscopy, changes in the dislocation structure and the mechanism leading to such strengthening have been found. During the creep test, the edge components of dislocations are depleted and disappear, and the cross slip of screw dislocations is blocked by numerous loops and helicoids that were formed under bending and transformed during the creep process. As a result, dislocation creep gradually turns into diffusion creep during one test. It is safe to assume that similar effects will be observed in polycrystals when the dominant texture direction will correspond to the required bending axis.
Source: openaire · Quality: candidate unverified · Source record ↗
References (32)
Show source-provided references
1. Materials challenges for nuclear systems10.1016/S1369-7021(10)70220-0 ↗
2. Structural method for the determination of the residual service life of steam pipelines operating for a long time
3. Failure assessment analysis of pipelines for heat and power generating plants according to the SINTAP procedures10.1016/j.ijpvp.2005.06.006 ↗
4. Problems, and prospects of direct thermionic conversion of unused heat energy to electrical energy of thermal power plants and metallurgical units
5. Review on thermionic energy converters
6. Dislocation substructure induced by creep in molybdenum single crystals10.1016/0001-6160(70)90152-5 ↗
7. Steady state creep and dislocation structure of molybdenum single crystals
8. Tungsten and molybdenum single crystals strengthening using pre-deformation
9. Dekhtyar AI, O.P. Karasevska OP, Kozyrsky GY, Kononenko VA. The Influence of the Structural State on the High-Temperature Creep of Tungsten and Molybdenum Single Crystals. Мoscow: Nauka, 1977, 162–167.
10. Structural factor in the equation of high-temperature creep at various stresses
11. Study of dislocation structure of metals by the oscillating crystal technique. Metallofiz
12. Distribution of dislocations in molybdenum monocrystals under action by different treatments
13. High temperature creep of molybdenum and tungsten single crystals substructure strengthened. Tungsten, Refractory Metals and Alloys 4
14. Regularities of the high-temperature creep of molybdenum and tungsten single crystals in the initial and substructure-strengthened state
15. Estimation of the dislocation density in tungsten single crystals at high-temperature creep using the oscillating crystal technique
16. Formation, and behavior of subboundaries in silicon-iron crystals
17. Some features of bending deformation and subsequent annealing of molybdenum single crystals
18. Annealing of plastic bent molybdenum single crystals
19. On the growth of the crystalline layer on a plastically bent rock salt single crystal
20. Structure of dislocation bands produced by bending stress in material f.c.c
21. The effect of a system of parallel dislocation walls on the mechanical characteristics of single crystals
22. Investigation of the effect of preliminary polygonization on the creep of silicon iron single crystals
23. Structural features of the high-temperature creep of single-crystal molybdenum in a wide range of applied stresses 2 substructure strengthened state
24. Demchenko · 1987
25. Thermal stability of substructure of bent molybdenum monocrystals
26. Plastic bending of molybdenum and tungsten single crystals and structural stability on heating
27. Kozyrskij GY, Kononenko VA. Device for mechanical testing of ring samples: Patent USSR N 460470, 1975. Bulletin № 6, (2 p).
28. Stress in anisotropic ring when stretched by hard sectors, Izv AS USSR
29. On the stresses determining the high-temperature creep rate of single crystals with a bcc lattice
30. Helical dislocations10.1103/PhysRev.107.1259 ↗
31. Dislocation-tangle formation
32. Hirth · 1967