Performance of high temperature resisted coated tools while cryogenic assisted drilling of SLM made Inconel-718

1. A review on fabrication of inconel alloys using different additive manufacturing techniques

2. Review on machining of additively manufactured nickel and titanium alloys10.1016/j.jmrt.2021.09.088 ↗

3. A review of mechanical properties of additively manufactured Inconel 718

4. Additive manufacturing of titanium and nickel- based superalloys: a review10.1016/j.matpr.2023.07.082 ↗

5. Experimental and numerical investigation of thermal loads in inocnel 718 machining10.1080/10426914.2018.1424907 ↗

6. Tool life and surface integrity aspects when drilling and hole making in inconel 71810.1016/j.jmatprotec.2007.08.080 ↗

7. Machinability studies on INCONEL 71810.1088/1757-899X/149/1/012019 ↗

8. The machinability of nickel-based alloys: a review10.1016/S0924-0136(98)00314-8 ↗

9. A review of developments towards dry and high speed machining of inconel 718 alloy10.1016/S0890-6955(03)00159-7 ↗

10. Tool wear and hole quality evaluation in cryogenic drilling of inconel 718 superalloy10.1016/j.triboint.2019.106084 ↗

11. Thermo-mechanical effects in drilling using metal working fluids and cryogenic cooling and their impact in tool performance10.1007/s11740-015-0619-6 ↗

12. Overcoming machining challenges in hybrid laser metal deposition of IN718 with heat-assisted minimum quantity lubrication10.1007/s00170-024-13646-0 ↗

13. Drilling process and resulting surface properties of inconel 718 alloy fabricated by selective laser melting additive manufacturing10.1016/j.procir.2020.02.110 ↗

14. Assessment of additive and subtractive sustainable manufacturing of inconel 62510.1016/j.triboint.2023.108655 ↗

15. Microstructure and machinability evaluation in micro milling of selective laser melted inconel 718 alloy10.1016/j.jmrt.2021.06.081 ↗

16. An analysis of surface integrity when drilling inconel 718 using palm oil and synthetic ester under MQL condition10.1080/10910344.2011.557967 ↗

17. Cooling techniques to improve the machinability and sustainability of light-weight alloys: a state-of-the-art review10.1016/j.jmapro.2020.12.013 ↗

18. Comprehensive machining analysis to establish cryogenic LN2 and LCO2 as sustainable cooling and lubrication techniques10.1016/j.triboint.2020.106314 ↗

19. Tool wear, hole quality, power consumption and chip morphology analysis for drilling Ti-6Al-4V using LN2 and LCO210.1016/j.triboint.2021.107190 ↗

20. Review on design and development of cryogenic machining setups for heat resistant alloys and composites10.1016/j.jmapro.2021.05.053 ↗

21. Comparison of LN2 and LCO2 based on machining performance indicators for drilling inconel 71810.1016/j.jmapro.2022.07.002 ↗

22. Life cycle assessment of drilling inconel 718 using cryogenic cutting fluids while considering sustainability parameters

23. The effects of cutting conditions on cutting temperature and hole quality in drilling of inconel 718 using solid carbide drills10.1016/j.jmapro.2018.01.003 ↗

24. Effect of machining parameters and cutting edge geometry on surface integrity when drilling and hole making in Inconel 71810.4271/2009-01-1412 ↗

25. Experimental investigations on single-lip deep hole drilling of superalloy inconel 718 with small diameters10.1016/j.jmapro.2015.06.001 ↗

26. Experimental studies and CFD simulation of the internal cooling conditions when drilling inconel 71810.1016/j.ijmachtools.2016.06.003 ↗

27. Evaluation of tool life in the dry machining of inconel 718 parts from additive manufacturing (AM)10.1007/s12541-019-00275-x ↗

28. Effect of nanoparticles in cutting fluid for structural machining of inconel 718

29. Surface integrity and tool life when turning inconel 718 using ultra-high pressure and flood coolant systems10.1243/09544054JEM936 ↗

30. Comparison of between direct and peck drilling for large aspect ratio in Ti-6Al-4V alloy10.1007/s00170-019-03314-z ↗

31. Tool wear and surface integrity of inconel 718 in dry and cryogenic coolant at high cutting speed10.1016/j.wear.2017.01.031 ↗

32. Surface integrity in cryogenic machining of nickel based alloy - inconel 71810.1016/j.jmatprotec.2010.12.013 ↗

33. Why hybrid PBF-LB – wrought Inconel 718 corrodes differently: interfacial microstructural origins and the influence of post-heat treatment

34. Future research directions in the machining of Inconel 71810.1016/j.jmatprotec.2021.117260 ↗

35. the comprehensive review on machining of inconel 718 superalloy

36. Study on modal analysis and chip breaking mechanism of inconel 718 by ultrasonic vibration-assisted drilling10.1007/s00170-019-04155-6 ↗

37. A state-of-the-art review on tool wear and surface integrity characteristics in machining of superalloys10.1016/j.cirpj.2021.08.005 ↗

38. Integrity S. Advances in hard – to – cut materials: manufacturing, properties, process mechanics and evaluation of 2020. doi:https://doi.org/10.3390/ma13030612.10.3390/ma13030612 ↗

39. Evaluation of drilled hole quality in al 2024 alloy10.1007/s00170-007-1049-1 ↗

40. Investigation the effect of particle size distribution on processing parameters optimisation in selective laser melting process

41. Energy consumption and economic modelling of performance measures in machining of wire arc additively manufactured inconel-625

42. Effects of mono/hybrid nanofluid strategies and surfactants on machining performance in the drilling of Hastelloy X10.1016/j.triboint.2021.106894 ↗

43. Experimental investigation of the influence of wire arc additive manufacturing on the machinability of titanium parts

44. Evaluation of tool wear, surface roughness/topography and chip morphology when machining of ni-based alloy 625 under MQL, cryogenic cooling and CryoMQL10.1016/j.jmrt.2019.12.069 ↗

45. Sustainable machining of high temperature nickel alloy - inconel 718: part 2 - chip breakability and optimization10.1016/j.jclepro.2014.10.085 ↗

46. Numerical analysis of chip formation and shear localisation processes in machining the Ti-6Al-4V titanium alloy10.1007/s00170-010-2789-x ↗

47. Effects of machining parameters and tool geometry on serrated chip formation, specific forces and energies in orthogonal cutting of nickel-based super alloy inconel 10010.1177/0954405413510291 ↗

48. Wang B, Liu Z, Hou X, et al. Influences of cutting speed and material mechanical properties on chip deformation and fracture during high-speed cutting of Inconel 718. Materials (Basel) 2018;11. doi:https://doi.org/10.3390/ma11040461.10.3390/ma11040461 ↗

49. Investigation on performance characteristics and metallographic transformation on drilling aluminium/titanium sandwich10.1177/1099636217724601 ↗