journal article·2022-11

Microstructure and mechanical behavior of cemented carbide with Al alloy binder fabricated by selective laser melting

Zijian Hu, Zhe Zhao, Xin Deng, Zhongliang Lu, Jianye Liu, Zhi Qu, Feng Jin

Publisher page

Abstract

Although cemented carbides have been increasingly investigated for additive manufacture, cemented carbides with low melting point metal binders have rarely been explored. In this study, a cemented carbide with AlSi10Mg alloy binder was fabricated by selective laser melting (SLM). The processing parameters were optimized through response surface methodology (RSM). The microstructure and mechanical properties of SLMed cast tungsten carbide (CC) - 40 wt% AlSi10Mg were studied. The SLMed carbide of CC - AlSi10Mg had much finer grain size of AlSi10Mg binder as compared with that of SLMed AlSi10Mg (1.9 μm vs. 7.3 μm). Noticeable metallurgical interaction between CC and AlSi10Mg binder was observed for SLMed carbide, which enhanced the bonding strength between CC and AlSi10Mg. SLMed carbide showed good Vickers hardness (236 ± 10 HV3), compression strength (639 ± 13 MPa), and abrasion wear resistance (0.47 ± 0.03 × 10 −3 mm 3N −1 m −1).
Source: expertdata · Quality: candidate unverified · Source record ↗

Research context

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (55)

Show source-provided references
1. Cemented carbide microstructures: a review10.1016/j.ijrmhm.2018.12.004 ↗
2. A review of cemented carbides for rock drilling: an old but still tough challenge in geo-engineering10.1016/j.ijrmhm.2013.01.003 ↗
3. Materials science of cemented carbides - an overview10.1016/S0261-3069(01)00007-3 ↗
4. The critical raw materials in cutting tools for machining applications: a review10.3390/ma13061377 ↗
5. Additive manufacturing of WC-Co hardmetals: a review10.1007/s00170-020-05389-5 ↗
6. Effect of binder saturation and powder layer thickness on the green strength of the binder jet 3D printing (BJ3DP) WC-12%Co powders10.1016/j.ijrmhm.2019.104991 ↗
7. Direct laser sintered WC-10Co/Cu nanocomposites10.1016/j.apsusc.2007.12.028 ↗
8. Synthesis of nanostructured WC-Co hardmetal by selective laser melting
9. Additive manufacturing of WC-13%Co by selective electron beam melting: achievements and challenges10.1016/j.ijrmhm.2019.105028 ↗
10. Phase control of WC-Co hardmetal using additive manufacturing technologies10.1080/00325899.2021.1937868 ↗
11. Additive manufacturing of WC-20Co components by 3D gel-printing10.1016/j.ijrmhm.2017.10.005 ↗
12. Electron beam melted beta-type Ti-24Nb-4Zr-8Sn porous structures with high strength-to-modulus ratio10.1016/j.jmst.2016.03.020 ↗
13. Powder-bed additive manufacturing for aerospace application: techniques, metallic and metal/ceramic composite materials and trends
14. Transformation-induced plasticity and high strength in beta titanium alloy manufactured by selective laser melting10.1016/j.mtla.2019.100299 ↗
15. Microstructure and mechanical properties of Inconel 718 produced by selective laser melting: sample orientation dependence and effects of post heat treatments10.1016/j.msea.2017.12.043 ↗
16. Additive manufacturing of metals10.1016/j.actamat.2016.07.019 ↗
17. Additive manufacturing of Ti6Al4V alloy: a review10.1016/j.matdes.2018.107552 ↗
18. A review of selective laser melting of aluminum alloys: processing, microstructure, property and developing trends10.1016/j.jmst.2018.09.004 ↗
19. Selective laser melting to manufacture “in situ” metal matrix composites: a review10.1002/adem.201801244 ↗
20. Particle-reinforced metal matrix nanocomposites fabricated by selective laser melting: a state of the art review10.1016/j.pmatsci.2019.04.006 ↗
21. Review on manufacture by selective laser melting and properties of titanium based materials for biomedical applications10.1179/1753555715Y.0000000076 ↗
22. Microstructure characteristics and formation mechanisms of in situ WC cemented carbide based hardmetals prepared by selective laser melting10.1016/j.msea.2010.08.075 ↗
23. Microstructure characterization of cemented carbide fabricated by selective laser melting process10.1016/j.ijrmhm.2018.05.001 ↗
24. On the microstructure and properties of an advanced cemented carbide system processed by selective laser melting10.1016/j.jallcom.2018.12.187 ↗
25. Microstructure analysis of high density WC-Co composite prepared by one step selective laser melting10.1016/j.ijrmhm.2019.104980 ↗
26. Microstructure evolution of WC-20Co cemented carbide during direct selective laser melting10.1080/00325899.2020.1815996 ↗
27. Development of the structure of cemented carbides during their processing by SLM and HIP10.3390/met10111477 ↗
28. Prcessability of WC-Co powder mixtures using SLM additive technology10.17973/MMSJ.2019_06_2018115 ↗
29. Role of Co content on densification and microstructure of WC-Co cemented carbides prepared by selective laser melting10.1007/s40195-021-01195-4 ↗
30. Correlation between microstructural heterogeneity and mechanical properties of WC-Co composite additively manufactured by selective laser melting10.1016/j.matlet.2021.129683 ↗
31. Investigation on additive manufacturing of tungsten carbide-cobalt by selective laser melting
32. Process chain development for additive manufacturing of cemented carbide10.1016/j.jmapro.2018.05.036 ↗
33. Selective laser melting of in-situ Al4SiC4+SiC hybrid reinforced Al matrix composites: influence of starting SiC particle size10.1016/j.surfcoat.2015.04.029 ↗
34. Influence of processing parameters on selective laser melted SiCp/AlSi10Mg composites: densification, microstructure and mechanical properties
35. Microstructure characteristics and its formation mechanism of selective laser melting SiC reinforced Al-based composites10.1016/j.vacuum.2018.11.022 ↗
36. In situ formation of D022-Al3Ti during selective laser melting of nano-TiC/AlSi10Mg alloy prepared by electrostatic self-assembly10.1016/j.vacuum.2021.110179 ↗
37. Aluminum with dispersed nanoparticles by laser additive manufacturing10.1038/s41467-019-12047-2 ↗
38. Enhanced micro-hardness and wear resistance of Al-15Si/TiC fabricated by selective laser melting10.1016/j.coco.2018.06.009 ↗
39. Effect of TiC content on the Al-15Si alloy processed by selective laser melting: microstructure and mechanical properties10.1016/j.optlastec.2019.105719 ↗
40. Nanometric TiC reinforced AlSi10Mg nanocomposites: powder preparation by high-energy ball milling and consolidation by selective laser melting10.1177/0021998314538870 ↗
41. Microstructural evolution and mechanical performance of in-situ TiB2/AlSi10Mg composite manufactured by selective laser melting10.1016/j.jallcom.2020.157287 ↗
42. Effect of TiB2 particles on microstructure and crystallographic texture of Al-12Si fabricated by selective laser melting10.1016/j.jallcom.2019.01.327 ↗
43. Selective laser melting additive manufacturing of 7xxx series Al-Zn-Mg-Cu alloy: cracking elimination by co-incorporation of Si and TiB2
44. Mechanical properties of SLM-printed aluminium alloys: a review10.3390/ma13194301 ↗
45. Selective laser melting of aluminum and its alloys
46. 3D printing of aluminium alloys: additive manufacturing of Aluminium alloys using selective laser melting10.1016/j.pmatsci.2019.100578 ↗
47. Selective laser melting of aluminium and aluminium metal matrix composites: review
48. A review of particulate-reinforced aluminum matrix composites fabricated by selective laser melting10.1016/S1003-6326(20)65357-2 ↗
49. Microstructure characteristics of Ni-based WC composite coatings by laser induction hybrid rapid cladding10.1016/j.msea.2007.07.058 ↗
50. The influence of carbide dissolution on the erosion-corrosion properties of cast tungsten carbide/Ni-based PTAW overlays10.1016/j.wear.2011.01.046 ↗
51. Decomposition of two phases WC and W2C in casting tungsten carbide particles in steel/iron substrate
52. Effects of interface formation kinetics on the microstructural properties of wear-resistant metal-matrix composites10.1016/j.msea.2010.06.060 ↗
53. Solidification of high-Cr white cast iron-WC particle reinforced composites10.1016/j.msea.2005.08.215 ↗
54. Reinforced cast metals - part I solidification microstructure10.1023/A:1004308027679 ↗
55. Microstructure and mechanical properties of hypoeutectic Al-Si composite reinforced with TiCN nanoparticles10.1016/j.matdes.2016.01.144 ↗