journal article·2019-01

Slurry erosion–corrosion wear behavior in SiC-containing NaOH solutions of Mo2NiB2 cermets prepared by reactive sintering

Xiao-Qiu Zheng, Ying Liu

Publisher page

Abstract

Abstract The slurry flow unit, such as coal-mining industry, erosive wear and erosion-corrosion can cause high rates of material loss, particularly in the hydrotransport system where corrosive slurries are encountered. Stainless steel, Metal Matrix Composites (MMCs) and so on, comprising a ductile binder with a reinforcing hard phase, are seeing greater applications as coatings and hard facing for critical components, where there is a requirement for high durability. In this paper, the erosion-corrosion performance of Mo2NiB2-based cermets applied by the reaction sintering process is evaluated. Three cermets, with varying volume fraction of Mo2NiB2 phase range, all with a Ni binder, have been considered. The microstructure and properties of Mo2NiB2-based cermets are investigated and discussed. The influence of volume fraction of Mo2NiB2 phase on the erosion and erosion–corrosion resistance is researched under alkaline conditions. Results reveal that the increasing of boron percent along with Mo2NiB2 phase pile up. Meanwhile, the hardness has direct relationship with the volume fraction of Mo2NiB2. The Mo2NiB2 phase plays an important role in wear behavior. The effect of Mo2NiB2 phase volume fraction on erosion–corrosion only containing NaOH solution of Mo2NiB2-based cermets is different from that on erosion containing both NaOH solution and SiC. It is advantageous for the corrosion resistance to contain more Mo2NiB2 phase. In alkaline slurry impact, the cermets with less Mo2NiB2 phase deteriorate largely due to corrosion which decreases the mechanical properties and speeds up the total loss of material. In alkaline slurry with SiC particles, the weight gain is produced by the synergistic effect of erosion and corrosion on the contrary. When the volume fraction of Mo2NiB2 is low, corrosive production is the main cause of weight gain due to increasing interference between impinging and reflected erodent. The Mo2NiB2 phase is more, the corrosion resistance is higher and the corrosive production is much less.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (33)

Show source-provided references
1. Erosion–corrosion resistance of various stainless steel grades in high-temperature sulfuric acid solution10.1016/j.wear.2016.06.007 ↗
2. Erosion-Corrosion of Low-Carbon Steel in the Absence and Presence of Slurry in Saline Water: Kinetic and Mathematical Views10.1007/s11668-016-0180-4 ↗
3. Evaluation of the synergistic erosion-corrosion behaviour of HVOF thermal spray coatings10.1016/j.surfcoat.2016.04.072 ↗
4. Research on the contributions of corrosion, erosion and synergy to the erosion–corrosion degradation of Ti(C,N)–based cermets10.1016/j.wear.2014.12.041 ↗
5. Synergistic erosion–corrosion behavior of Al–brass alloy at various impingement angles10.1016/j.wear.2014.07.008 ↗
6. Erosion–corrosion behavior of Ti(C,N)-based cermets with different TiN contents10.1016/j.ijrmhm.2013.10.006 ↗
7. Erosion behavior of Ti(C,N)-based cermet in solid–liquid two phase flow10.1016/j.ijrmhm.2013.04.004 ↗
8. Corrosion and Erosion-Corrosion Processes of Metal-Matrix Composites in Slurry Conditions10.1007/s11665-011-9926-z ↗
9. Effect of Sub-critical Tempering and Deep Cryogenic Treatment on Slurry Erosion of Cr-Mn-Cu White Cast Irons10.2355/isijinternational.54.2294 ↗
10. Slurry Erosion–Corrosion of Carburized AISI 5117 Steel10.1007/s11249-013-0155-5 ↗
11. Erosion–corrosion behaviour of lean duplex stainless steels in 3.5% NaCl solution10.1016/j.wear.2012.12.007 ↗
12. Investigation of erosion–corrosion mechanisms of UNS S31603 using FIB and TEM10.1016/j.triboint.2011.05.012 ↗
13. A study of the erosion-corrosion behaviour of engineering steels for marine pumping applications10.1016/0043-1648(95)07145-8 ↗
14. The influence of applied potential on the erosion-corrosion behavior of AISI321 stainless steel in acidic slurry medium10.1016/0043-1648(95)07134-2 ↗
15. Effect of impact angle on the slurry erosion–corrosion of 304L stainless steel10.1016/S0043-1648(00)00344-6 ↗
16. Erosion-corrosion of copper-nickel-alloys in sea-water and other aqueous environments - literature-review10.5006/0010-9312-32.6.242 ↗
17. A study of the erosion-corrosion behavior of engineering steels for marine pumping applications10.1016/0043-1648(95)07145-8 ↗
18. The synergistic effect between erosion and corrosion in acidic slurry medium10.1016/0043-1648(95)07132-6 ↗
19. Microabrasion of WC–Co hardmetals in corrosive media10.1016/j.wear.2003.09.003 ↗
20. Erosion–corrosion behaviour of WC-based MMCs in liquid–solid slurries10.1016/j.wear.2005.02.037 ↗
21. Exposure effects of alkaline drilling fluid on the microscale abrasion–corrosion of WC-based hardmetals10.1016/j.wear.2006.12.047 ↗
22. Wear and corrosion behaviour of thermally sprayed cermet coatings10.1016/S0257-8972(00)01141-5 ↗
23. In-situ metal matrix composite steels: Effect of alloying and annealing on morphology, structure and mechanical properties of TiB2 particle containing high modulus steels10.1016/j.actamat.2016.01.048 ↗
24. Microhardness and microstructure evolution of TiBreinforced Inconel 625/TiBcomposite produced by selective laser melting10.1016/j.optlastec.2016.01.010 ↗
25. Influence and effectivity of Sm 2 O 3 and Cr 3 C 2 grain growth inhibitors on sintering of WCoB–TiC based cermets10.1016/j.ceramint.2015.07.049 ↗
26. Mechanical Properties of W_2NiB_2-Ni Boride Base Cermets10.2497/jjspm.60.349 ↗
27. First-principles study on the electronic structure and elastic properties of Mo2NiB2 doped with V
28. Effect of Mo/B atomic ratio on the properties of Mo 2 NiB 2 -based cermets10.3139/146.111209 ↗
29. Development of Mo_2NiB_2 Base Cermets with High Strength and Excellent Corrosion Resistance for Plastic Injection Molding Machine Parts10.2497/jjspm.53.447 ↗
30. Reactive synthesis and mechanical properties of Mo 2NiB 2 based hard alloy10.1016/j.ijrmhm.2009.11.002 ↗
31. Development and application of high strength ternary boride base cermets10.1016/j.jssc.2006.01.023 ↗
32. Synthesis and microstructure evolution during vacuum sintering of Mo2FeB2 based cermets10.1016/j.ijrmhm.2014.03.010 ↗
33. Effect of coalescence on the grain coarsening during liquid-phase sintering of TaC-TiC-Ni cermets10.1016/S1359-6454(00)00117-8 ↗