journal article·2018-12

Effects of fabrication method on initial powder characteristics and liquid phase sintering behaviour of tungsten

Mahmut Erol, Metehan Erdoğan, İshak Karakaya

Publisher page

Abstract

Abstract Direct electrochemical production of tungsten involves removal of oxygen in solid state from an important tungsten compound, calcium tungstate, in molten salts. A detailed experimental study was performed to characterize the liquid phase sintering behaviour of the tungsten powder (WE), which was produced by the direct electrochemical reduction technique. All of the tungsten heavy alloy (WHA) compositions covered in this study, contained four parts nickel, one part cobalt and over 90 wt% tungsten. The pellets were sintered at 1500 and 1550 °C under continuous flow of an equimolar hydrogen-argon gas mixture. A commercially available tungsten powder (WC) was also used to prepare the same tungsten heavy alloy compositions as those prepared by the electrochemically produced tungsten powder to act as a control group. Scanning electron microscopy (SEM), X-ray diffraction (XRD), X-ray fluorescence (XRF) and hardness measurements were employed for characterization. The analyses provided that; the tungsten powder as obtained from the direct electrochemical reduction process contained some unreduced CaWO4 particles and they limited the grain growth and mass transport in the liquid phase. Although calculated relative densities were a bit lower than desired, the tungsten heavy alloys produced by the electrochemical reduction technique was promising for use when average grain size, dissolved tungsten contents and general/matrix hardness values are considered.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (34)

Show source-provided references
1. Novel fluidised cathode approach for the electrochemical reduction of tungsten oxide in molten LiCl–KCl eutectic10.1016/j.elecom.2014.01.022 ↗
2. Preparation and characterization of tungsten powder through molten salt electrolysis in a CaWO4–CaCl2–NaCl system10.1016/j.ijrmhm.2011.11.004 ↗
3. Electrochemical behavior of tungsten ions from WC scrap dissolution in a chloride melt10.1016/j.electacta.2015.10.071 ↗
4. Electrochemical reduction of tungsten compounds to produce tungsten powder10.1007/s11663-010-9374-4 ↗
5. On the electrochemical reduction mechanism of CaWO4 to W powder10.1007/s11663-012-9689-4 ↗
6. Karakaya · 2009 · 054 819A1
7. Erdoğan · 2013
8. Tang · J. Electrochem. Soc. · 2012 · 159
9. Caceres, effect of microstructure on the abrasive wear properties of infiltrated tungsten alloys10.1016/S1044-5803(02)00201-2 ↗
10. Nandy, effect of solution treatment temperature and cooling rate on the mechanical properties of tungsten heavy alloy10.1016/j.msea.2017.01.113 ↗
11. Processing and microstructural characterization of liquid phase sintered tungsten-nickel-cobalt heavy alloys10.1016/j.ijrmhm.2014.12.009 ↗
12. Microstructure and mechanical properties of tungsten heavy alloys10.1016/j.msea.2010.08.071 ↗
13. Experimental studies of oxygen and carbon segregation at the interfacial boundaries of a 90W–7Ni–3Fe tungsten heavy alloy10.1016/j.matchar.2004.06.011 ↗
14. Processing strategy for consolidating tungsten heavy alloys for ordnance applications10.1016/S0254-0584(00)00426-0 ↗
15. Microstructure and mechanical properties of mechanically alloyed and solid-state sintered tungsten heavy alloys10.1016/S0921-5093(00)00968-0 ↗
16. The rheological and sintering behavior of W–Ni–Fe nano-structured crystalline powder10.1016/S0924-0136(02)01090-7 ↗
17. Influence of minor elements additions on microstructure and properties of 93W–4·9Ni–2·1Fe alloys bull
18. Effect of alloying addition and microstructural parameters on mechanical properties of 93% tungsten heavy alloys10.1016/j.msea.2015.05.046 ↗
19. Refractory metal alloying: a new method for improving mechanical properties of tungsten heavy alloys10.1016/j.jallcom.2017.03.174 ↗
20. Özdemir · 2016 · 596
21. Thompson · 1985
22. ASTM · 2010
23. Effect of cyclic heat treatment and swaging on mechanical properties of the tungsten heavy alloys10.1016/j.msea.2016.01.024 ↗
24. Nagender · 1991
25. Swaging and heat treatment studies on sintered 90W-6Ni-2Fe-2Co tungsten heavy alloy10.1016/j.ijrmhm.2012.03.003 ↗
26. Segregation of molybdenum atoms to the liquid-solid interfaces in liquid phase sintering of W-8 pct Mo-7 pct Ni-3 pct Fe10.1007/s11661-001-0105-y ↗
27. Precipitation of an intermetallic phase in Mo-alloyed tungsten heavy alloys10.2320/matertrans.44.358 ↗
28. Mechanical properties of molybdenum alloyed liquid phase-sintered tungsten-based composites10.1007/BF02670690 ↗
29. The effect of Mo addition on the liquid-phase sintering of W heavy alloy10.1007/BF02663862 ↗
30. Coalescence of tungsten grains around molybdenum grains in the presence of a liquid phase10.1016/S1359-6462(02)00069-6 ↗
31. Fabrication, characterization, and mechanical properties of 93W–4.9Ni–2.1Fe/95W–2.8Ni–1.2Fe–1Al2O3 heavy alloy composites10.1016/j.msea.2015.04.026 ↗
32. Fabrication and properties of mechanically alloyed oxide-dispersed tungsten heavy alloys10.1016/S0921-5093(03)00641-5 ↗
33. Effect of microstructural parameters on the properties of W-Ni-Fe alloys10.1016/S1001-0521(07)60201-0 ↗
34. Effect of size and shape of tungsten particles on dynamic torsional properties in tungsten heavy alloys10.1007/s11661-999-0275-6 ↗