Impact of cobalt content and grain growth inhibitors in laser-based powder bed fusion of WC-Co
Source abstract
Abstract
Processing of tungsten carbide‑cobalt (WC-Co) by laser-based powder bed fusion (PBF-LB) can result in characteristic microstructure defects such as cracks, pores, undesired phases and tungsten carbide (WC) grain growth, due to the heterogeneous energy input and the high thermal gradients. Besides the processing conditions, the material properties are affected by the initial powder characteristics. In this paper, the impact of powder composition on microstructure, phase formation and mechanical properties in PBF-LB of WC-Co is studied. Powders with different cobalt contents from 12 wt.-% to 25 wt.-% are tested under variation of the laser parameters. Furthermore, the impact of vanadium carbide (VC) and chromium (Cr) additives is investigated. Both are known as grain growth inhibitors for conventional sintering processes. The experiments are conducted at a pre-heating temperature of around 800 ◦C to prevent crack formation in the samples. Increasing laser energy input reduces porosity but leads to severe embrittlement for low cobalt content and to abnormal WC grain growth for high cobalt content. It is found that interparticular porosity at low laser energy is more severe for low cobalt content due to poor wetting of the liquid phase. Maximum bending strength of σB > 1200 MPa and Vickers hardness of approx. 1000 HV3 can be measured for samples generated from WC-Co 83/17 powder with medium laser energy input. The addition of V and Cr leads to increased formation of additional phases such as Co3W3C, Co3V and Cr23C6 and to increased lateral and multi-laminar growth of the WC grains. In contrast to conventional sintering, a grain growth inhibiting effect of V and Cr in the laser molten microstructure is not achieved.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (31)
Show source-provided references
1. Additive manufacturing of application optimized tungsten carbide precision tools
2. A review of additive manufacturing of cermets
3. Investigation on additive manufacturing of tungsten carbide-cobalt by selective laser melting10.1016/j.procir.2015.08.060 ↗
4. Powder bed fusion processes
5. Strongly out-of-equilibrium columnar solidification during laser powder-bed fusion in additive manufacturing10.1103/PhysRevApplied.11.014025 ↗
6. Residual stresses in selective laser sintering and selective laser melting10.1108/13552540610707013 ↗
7. Parameter study on laser beam melting of WC-co at 800°C pre-heating temperature. In: Proc
8. Investigations on additive manufacturing of WCCo hard metals by laser beam melting10.3139/147.110477 ↗
9. High temperature mechanical properties of WC–co hard metals10.1016/j.ijrmhm.2016.01.002 ↗
10. Impact of laser irradiation on microstructure and phase development of tungsten carbide - cobalt
11. Liquid-phase sintering of tungsten carbide-cobalt by laser radiation
12. Thermodynamic properties of the Co-WC system10.1007/BF02651660 ↗
13. A study of the effect of carbon content on the structure and properties of sintered WC-Co alloys
14. Cemented carbide microstructures: a review10.1016/j.ijrmhm.2018.12.004 ↗
15. A history of fine grained hardmetal10.1016/0263-4368(95)92671-6 ↗
16. Location of VC in VC, Cr3C2 codoped WC–Co cermets by HREM and EELS10.1016/S0263-4368(01)00071-3 ↗
17. Cr-rich layer at the WC/Co interface in Cr-doped WC–Co cermets: segregation or metastable carbide?10.1016/j.jcrysgro.2004.05.101 ↗
18. Schwanekamp · 2020
19. Laser-based additive manufacturing of WC–Co with high-temperature powder bed preheating
20. Gläser · 2010
21. Baum · 2014
22. Bondar · 2010
23. A review of parameters influencing some mechanical properties of tungsten carbide-cobalt alloys10.1179/pom.1970.13.25.002 ↗
24. Properties of hardmetals and cermets
25. A computational study of thin cubic carbide films in WC/co interfaces10.1016/j.actamat.2010.09.021 ↗
26. Determination of the linear expansion coefficient of Co-W-C eta-carbides using a high-temperature X-ray diffraction technique10.1016/0022-5088(77)90093-5 ↗
27. The Co-V (cobalt-vanadium) system10.1007/BF02649921 ↗
28. The shape of WC crystals in cemented carbides10.1016/S0921-5093(97)00509-1 ↗
29. Pellan · 2016 · 2016
30. Segregation amount of dopants at WC/Co Interface in Cr3C2- and VC+Cr3C2-doped WC-Co submicro-grained hardmetals
31. Einsatz von pulvermetallurgischen Werkstoffen bei einem Werkzeughersteller – Additive Fertigung von Wolframcarbid-Cobalt-Hartmetallen