Effect of counterbody on the dry sliding wear performance of plasma sprayed calcia-stabilized zirconia coating
Source abstract
Abstract
Abstract In this study, the effect of counterbody on the dry sliding wear behavior of plasma sprayed calcia-stabilized zirconia coating was investigated. The commercial ZrO2-5CaO coating powder (Metco 201NS, −53 + 11 μm) was deposited onto the surface of AISI 316L substrate using Atmospheric Plasma Spray method. Dry sliding wear tests were performed with Al2O3 and WC-Co counterbody balls at different loads (5 N, 10 N and 15 N) and sliding speeds (10 mm/s, 20 mm/s and 30 mm/s) using a ball-on-disc device. From the test results, the COF values obtained from the Al2O3 ball were recorded to be lower than that of the WC-Co ball especially at 20 N and 30 N loads. The sliding speed did not cause a remarkable change in the COF values of the wear tests performed with both counterbody balls. However, in the case of WC-Co ball, COF values also increased especially with increasing the load from 5 N to 10 N at the 20 mm/s of sliding speed. In general, increasing load and sliding speed led to an increase in the wear volume loss values for all the tests. When using Al2O3 ball, under the 5 N load, lots of pitting and spalling zones were observed, whereas for 10 N and 15 N loads, plastically deformed worn areas which had lots of wear debris and deep cracks were determined. As for the WC-Co ball, the plastic deformation was observed as the predominant wear mechanism as well as the swelling-induced spallation and delamination. In addition, the wear mechanisms identified as a result of this study were explained by associating them with the Hertzian contact theory.
Source: openaire · Quality: candidate unverified · Source record ↗
References (29)
Show source-provided references
1. Basu · 2011
2. Hutchings · 1992
3. Zum Gahr · 1987
4. The influence of substrate hardness on the formation and endurance of molybdenum disulphide films10.1016/0043-1648(67)90082-8 ↗
5. Coaxial laser cladding of Al2O3-13%TiO2 powders on Ti-6Al-4V alloy10.1016/j.surfcoat.2012.05.027 ↗
6. Mahamood · 2018
7. Ceramic coating technology10.1007/BF02811962 ↗
8. Friction and wear behavior of ZrO2–Al2O3 composite coatings deposited by air plasma spraying: correlation with physical and mechanical properties10.1016/j.surfcoat.2009.03.056 ↗
9. The analysis of the friction and wear mechanisms of plasma sprayed ceramic coatings at 450 °C10.1016/0043-1648(88)90063-4 ↗
10. Tribological behavior of plasma sprayed zirconia coatings10.1016/S0043-1648(96)07395-4 ↗
11. Wear behavior of plasma-sprayed partially stabilized zirconia on a steel substrate10.1016/0043-1648(93)90556-2 ↗
12. Unlubricated friction and wear behavior of low-pressure plasma sprayed ZrO2 coating at elevated temperatures10.1016/S0272-8842(00)00072-9 ↗
13. Oerlikon Metco · 2017
14. Thermal barrier coatings for gas-turbine engine applications10.1126/science.1068609 ↗
15. Effects of hardness on the wear mode diagram in lubricated sliding friction of carbon steels10.1016/0043-1648(90)90187-F ↗
16. Effect of hardness on three very different forms of wear10.1016/S0043-1648(96)07414-5 ↗
17. The hardness and sliding wear behaviour of a bainitic steel10.1016/S0043-1648(96)07411-X ↗
18. Buckley · 1981
19. Fischer-Cripps · 2007
20. Indentation fracture
21. A model for microcrack initiation and propagation beneath hertzian contacts in polycrystalline ceramics10.1016/0956-7151(94)90378-6 ↗
22. Model for fretting wear of brittle ceramics10.1016/j.actamat.2009.01.013 ↗
23. Hertz · 1896
24. Johnson · 1985
25. Zhang · 2007
26. Sliding friction and wear behaviour of Titanium-Zirconium-Molybdenum (TZM) alloy against Al2O3 and Si3N4 balls under several environments and temperatures10.1016/j.triboint.2016.10.049 ↗
27. Dry sliding friction and wear behaviour of hardened AISI D2 tool steel with different hardness levels10.1016/j.triboint.2013.05.006 ↗
28. Wear mechanisms of WC-Co cutting tools from high-speed tribological tests10.1016/j.wear.2008.12.035 ↗
29. Effects of pressure and sliding speed on the friction and wear properties of Al–40Zn–3Cu–2Si alloy: a comparative study with SAE 65 bronze10.1016/j.msea.2008.06.008 ↗