Experimental investigation on tool wear characteristics of PVD and CVD coatings during face milling of Ti 6242S and Ti-555 titanium alloys
Source abstract
Abstract
Abstract Ti 6242S and Ti-555, as two typical titanium alloys, are often used to manufacture high-temperature aeroengine parts and landing gear components, respectively. They have different chemical composition and microstructure, which make them have different mechanical properties, and also affect their machinability. In this paper, face milling experiments were carried out to evaluate the wear performance by using CVD-Ti(C, N) + Al2O3 + TiN, PVD-(Ti, Al)N + TiN coated and uncoated tools. The results show that Ti-555 has the worse machinability than that of Ti 6242S. When milling Ti 6242S, all tools suffered adhesive wear and diffusion wear; the wear of Ti(C, N) + Al2O3 + TiN coated tool was more serious than that of other tools due to the blunt cutting edge; (Ti, Al)N + TiN coated tool suffered micro chipping and coating peeling with the minimal wear loss. When milling Ti-555, uncoated tool suffered serious chipping, abrasive wear and adhesive wear; Ti(C, N) + Al2O3 + TiN coated tool suffered serious chipping and coating peeling with short tool life; (Ti, Al)N + TiN coated tool suffered coating peeling, adhesive wear and diffusion wear. Overall, (Ti, Al)N + TiN coated tools have the longest tool life and are preferred for face milling of Ti 6242S and Ti-555 titanium alloys.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (24)
Show source-provided references
1. Mitigation of abrasive wear damage of Ti–6Al–4V by laser surface alloying10.1016/j.matdes.2015.02.010 ↗
2. Advanced cutting conditions for the milling of aeronautical alloys
3. Correlation between microstructures and mechanical properties under tensile and compression tests of heat-treated Ti-6Al-4 V ELI alloy produced by additive manufacturing for biomedical applications10.1016/j.jmatprotec.2017.09.022 ↗
4. Fatigue of the near-alpha Ti-alloy Ti624210.1007/s11340-009-9238-5 ↗
5. Dynamic softening behavior of TC18 titanium alloy during hot deformation10.1016/j.matdes.2015.01.009 ↗
6. Flow characterization of a duplex near α Ti6242 alloy through interrelation of microstructural evolution, 3D activation energy map, and processing map10.1002/adem.201500426 ↗
7. Constitutive modeling for high-temperature flow behavior of Ti-6242S alloy10.1016/j.msea.2016.11.002 ↗
8. Hot deformation of Ti-5Al-5Mo-5 V-1Cr-1Fe near β titanium alloys containing thin and thick lamellar α phase10.1016/j.msea.2013.02.033 ↗
9. Effects of duplex jets high-pressure coolant on machining temperature and machinability of Ti-6Al-4V superalloy10.1016/j.jmatprotec.2017.10.040 ↗
10. Machining of titanium alloy (Ti-6Al-4V)—theory to application10.1080/10910344.2014.991031 ↗
11. Effect of cryogenic compressed air on the evolution of cutting force and tool wear during machining of Ti–6Al–4V alloy10.1016/j.jmatprotec.2015.02.017 ↗
12. Wear performance of (nc-AlTiN)/(a-Si3N4) coating and (nc-AlCrN)/(a-Si3N4) coating in high-speed machining of titanium alloys under dry and minimum quantity lubrication (MQL) conditions10.1016/j.wear.2013.02.001 ↗
13. On the volumetric assessment of tool wear in machining inserts with complex geometries—part II: experimental investigation and validation on Ti-6Al-4V
14. The effect of monolayer TiCN-, AlTiN-, TiAlN-and two layers TiCN+ TiN-and AlTiN+ TiN-coated cutting tools on tool wear, cutting force, surface roughness and chip morphology during high-speed milling of Ti6Al4V titanium alloy10.1177/0954405416666905 ↗
15. Experimental investigation on the effect of the material microstructure on tool wear when machining hard titanium alloys: Ti–6Al–4V and Ti-55510.1016/j.ijrmhm.2013.04.011 ↗
16. Wear characteristics and performance of multi-layer CVD-coated alloyed carbide tool in dry end milling of titanium alloy10.1016/j.surfcoat.2005.07.063 ↗
17. Mathematical modelling and optimization of cutting force, tool wear and surface roughness by using artificial neural network and response surface methodology in milling of Ti-6242S10.3390/app7101064 ↗
18. Davim · 2014
19. Machinability of titanium alloys (Ti6Al4V and Ti555. 3)10.1016/j.jmatprotec.2008.06.020 ↗
20. Evolution of microstructure and tensile properties during the three-stage heat treatment of TA19 titanium alloy10.1016/j.msea.2018.01.046 ↗
21. The crack initiation behavior and the fatigue limit of Ti–5Al–5Mo–5V–1Cr–1Fe titanium alloy with basket-weave microstructure10.1016/j.jallcom.2015.01.077 ↗
22. Tool wear characteristics of binderless CBN tools used in high-speed milling of titanium alloys10.1016/j.wear.2004.09.066 ↗
23. Tool wear in disk milling grooving of titanium alloy10.1177/1687814016671620 ↗
24. Evaluation of principal wear mechanisms of cemented carbides and ceramics used for machining titanium alloy IMI 31810.1179/mst.1986.2.1.47 ↗