journal article·2017-09

Analysis on brazed diamond joints with modified Cu-based filler alloy

Jinbin Lu, Wenchun Qi, Yang Li, Fangjuan Qi, Mi Qian, Xinkai Qiu

Publisher page

Abstract

Abstract Filler alloy can strongly influence the performance of brazed monolayer diamond grinding tools. Cu-Sn-Ti and modified Cu-based filler alloy added with Ni-Cr-B-Si were used to braze diamond. The morphology of the diamond and the microstructure of the filler alloy were analyzed by SEM, EDS, and XRD. The hardness of the alloy was also determined with a microhardness tester. The results show that filler alloy containing Cu, Sn metal powder, and 16%Ni-Cr-B-Si is suitable for brazing diamond. The morphology of the brazed diamond is intact, and the filler alloy catalyzes the chemical metallurgical bonding with the diamond. Different kinds of carbide are formed on different crystal faces of the diamond. Cu-based dendrites, Cu5.6Sn, Cu3Sn, and Ni3Sn are formed on the filler alloy during solidification. The hardness of the modified Cu-based filler alloy increases with increasing proportion of Ni-Cr-B-Si added. In particular, the hardness of the modified Cu-based filler alloy containing 16 wt% Ni-Cr-B-Si reaches 340–360 HV0.3, which is three times the hardness of the Cu-Sn-Ti filler metal.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (22)

Show source-provided references
1. Brazed diamond grid: a revolutionary design for diamond saws10.1016/S0925-9635(99)00086-2 ↗
2. On performance of brazed-bond monolayer diamond grinding wheel10.1016/S0007-8506(07)62003-4 ↗
3. Diamond–metal interfaces in cutting tools: a review10.1007/s10853-011-6164-6 ↗
4. Joining interface and grain fracture of single-layer brazed grinding wheels with binderless CBN grains10.1007/s00170-013-4917-x ↗
5. Brazed joints of CBN grains and AISI 1045 steel with AgCuTi-TiC mixed powder as filler materials10.1007/s12613-011-0502-1 ↗
6. Study on the use of CuSnTi brazing alloy for induction brazing of diamond grits surface-treated by direct current plasma chemical vapor deposition10.1016/j.ijrmhm.2013.05.006 ↗
7. Modeling and simulation of the TiC reaction layer growth during active brazing of diamond using DICTRA10.1016/j.commatsci.2013.05.025 ↗
8. The effects of solder alloys on the morphologies and mechanical properties of brazed diamond grits10.1016/j.ijrmhm.2013.10.003 ↗
9. Effect of Cu-P-Sn on brazing diamond with Ni-based filler alloy10.1007/s00170-016-9400-z ↗
10. Interfacial segregation of Ti in the brazing of diamond grits onto a steel substrate using a Cu-Sn-Ti brazing alloy
11. Finite element analysis of thermal effects on brazed cold diamond grit10.1007/s12666-015-0516-x ↗
12. Microstructure, residual stresses and shear strength of diamond–steel-joints brazed with a Cu–Sn-based active filler alloy10.1016/j.ijrmhm.2011.06.006 ↗
13. Microstructure and phase formation in a rapidly solidified laser-deposited Ni-Cr-B-Si-C hardfacing alloy10.1007/s11661-013-2004-4 ↗
14. Phase formation and properties of vanadium-modified Ni–Cr–B-Si–C laser-deposited coatings10.1007/s10853-012-7117-4 ↗
15. Study of the sliding wear and friction behavior of WC+NiCrBSi laser cladding coatings as a function of actual concentration of WC reinforcement particles in ball-on-disk test10.1007/s11249-016-0734-3 ↗
16. Microstructure and mechanical properties of pre-brazed diamond abrasive grains using Cu–Sn–Ti alloy10.1016/j.ijrmhm.2014.10.015 ↗
17. Laser brazing of diamond grits using a Cu–15Ti–10Sn brazing alloy10.2320/matertrans.43.2604 ↗
18. Microstructure and mechanical performance of Cu-Sn-Ti-based active braze alloy containing in situ formed nano-sized TiC particles10.1007/s11665-015-1471-8 ↗
19. Polarized micro-Raman spectroscopy for studying stresses in as-grown and tensile-tested diamond films10.1016/j.surfcoat.2007.08.050 ↗
20. The interfacial reaction between diamond grit and Ni-based brazing filler metal10.2320/matertrans.48.889 ↗
21. Interfacial microstructure and performance of brazed diamond grits with Ni–Cr–P alloy10.1016/j.jallcom.2008.09.134 ↗
22. Reaction products at brazed interface between Ag–Cu–V filler metal and diamond (111)10.1007/s10853-006-0707-2 ↗