Optimized Brazing Performance of Amorphized Cu-P-Sn-Ni Fillers for Copper Joining
Source abstract
Abstract
In this study, amorphous Cu86P7.5Sn4.5Ni2(wt.%) fillers were prepared using the melt spinning method with different rolling speeds. The wetting performance of these fillers on copper was assessed under different temperatures and holding times. The results indicated that the fillers obtained through the melt spinning technique exhibited lower melting temperatures than the as-cast filler. When processed at a rolling speed of 20 m/s, the amorphization of the filler was not sufficient. The higher rolling speed promoted the formation of the amorphous structure. The amorphous filler produced at 30 m/s exhibited the narrowest melting range and the lowest liquidus temperature (622 °C), which is approximately 100 °C lower than that of the as-cast filler (725 °C). Furthermore, the amorphous fillers also exhibited better wettability toward copper under the same conditions. Notably, the amorphous filler fabricated at 30 m/s demonstrated superior wettability at 750 °C for 90 s. Owing to the optimal wettability of the amorphized filler toward copper and the lower liquid temperature, the brazed copper joint achieved a shear strength of 223.2 MPa. The fracture of the four joints occurred in the base metal. In this study, we explored the brazing performance of amorphized Cu-based fillers, facilitating the solid bonding of copper at lower brazing temperatures.
Source: crossref · Quality: baseline
Affiliations
Agriculture College, Jinhua University of Vocational Technology, Jinhua 321017, China
General Education College, Jinhua University of Vocational Technology, Jinhua 321017, China
Academician Workstation, Jinhua University of Vocational Technology, Jinhua 321017, China
Funding
Science Foundation of Jinhua
References (21)
Show source-provided references
1. Brazing techniques for the fabrication of biocompatible carbon-based electronic devices10.1016/j.carbon.2016.05.047 ↗
2. Guo, L., Zuo, P.C., Zhang, Z.Q., Zhang, Q.W., Zhao, M.Y., Hou, X.Y., Wu, J.S., and Zhang, B.W. (2023). A Review of Cu–Ni–Sn Alloys: Processing, Microstructure, Properties, and Developing Trends. Materials, 16.10.3390/ma16010444 ↗
3. Luo, Q.C., Xue, S.B., and Wu, J. (2021). Influences of Sn on Properties of Ag-Based and Cu-Based Brazing Filler Metals. Crystals, 11.10.3390/cryst11111403 ↗
4. Micromorphology change and microstructure of Cu-P based amorphous filler during heating process10.1515/htmp-2019-0013 ↗
5. Sami, M.M., Zaharinie, T., Yusof, F., and Ariga, T. (2020). Investigation on strength and microstructural evolution of porous Cu/Cu brazed joints using Cu-Ni-Sn-P Filler. Metals, 10.10.3390/met10030416 ↗
6. Effects of Forming Specific Pressure and Filling Speed on Microstructure and Mechanical Properties of Thin-Walled CuSn10P1 Alloy Parts by Rheological Squeeze Forming
7. Bao, L., Yang, J., Zhang, S.N., and Ding, T.R. (2024). Effect of E-waste copper alloy additions on the microstructure and organization of Cu90PSn brazing joints. Front. Chem., 12.10.3389/fchem.2024.1342117 ↗
8. Thermodynamic Reassessment of the Binary Cu-Sn, Cu-P, and Sn-P and Ternary Cu-Sn-P Systems10.1007/s11669-024-01112-z ↗
9. Effects of Ga addition on microstructure and properties of Sn-Ag-Cu/Cu solder joints10.1016/j.jallcom.2014.11.030 ↗
10. Investigation of intergranular penetration behavior in CrMnFeCoNi HEA/304 SS dissimilar brazing joints10.1016/j.intermet.2020.106940 ↗
11. Effect of rare earth elements scandium on Sn-0.7Cu brazing metal: First-principles calculation10.1016/j.surfin.2024.104960 ↗
12. Wu, J., Xue, S.B., and Luo, Q.C. (2022). Development of a Novel Low-Silver Cu-P Brazing Filler Metal Bearing Sn. Crystals, 12.10.3390/cryst12010066 ↗
13. Achieving superior strength and ductility in TiAl/Ti2AlNb dissimilar brazed joints by controlling the brittle Zr(Ni,Cu)3 intermetallic compound10.1016/j.msea.2025.148225 ↗
14. Effect of Ni on the wetting and brazing characterization of 304 stainless steel by Ag–Cu alloy10.1007/s10853-023-08372-z ↗
15. Latent heat of crystallization and precursor film induced superior wettability of tungsten heavy alloy by Cu-Ti based amorphous alloy10.1016/j.ijrmhm.2021.105722 ↗
16. Current Review on the Research Status of Cemented Carbide Brazing: Filler Materials and Mechanical Properties10.1007/s12613-020-1999-y ↗
17. A New Technique for Brazing Porous Copper to Copper Substrate Using CuNiSnP Amorphous Filler Metal10.1007/s11665-025-11086-9 ↗
18. Glass and nanocrystalline phase formation in CuZrAg alloys: Insights from combinatorial thin film libraries studied by mapping synchrotron X-ray diffraction10.1016/j.matdes.2024.113144 ↗
19. Study on Brazing of SiC Ceramics with Zr-Cu-Nb Filler Metal10.1007/s11665-023-08501-4 ↗
20. Study on properties of AgCuInTi filler metal for active bonding of alumina ceramic10.1007/s40194-024-01920-4 ↗
21. Brazing of 6061 aluminum alloy with the novel Al-Si-Ge-Zn filler metal10.1016/j.matlet.2016.05.052 ↗