journal article·2008-12

A comparative study of the pin-bearing responses of two glass-based fibre metal laminates

R.M. Frizzell, C.T. McCarthy, M.A. McCarthy

Composites Science and Technology· Volume 68· Issue 15-16
Publisher page

Abstract

Abstract The pin-bearing behaviour of two commercially available glass-based fibre metal laminates (FMLs), GLARE® 2 and GLARE® 3, is presented. Results shown include bearing stress, strain, stiffness and strength, surface strains in the vicinity of the hole, and damage progression using microscopy. The initial stiffness, the bearing strain at which non-linearity first occurs and the initial rate of stiffness loss were similar for both materials, indicating that the initial bearing behaviour of these FMLs is dominated by the metal layers. Microscopy results provided experimental evidence that delamination first occurs in FMLs as a result of interlaminar normal stresses from pin loading and not because of buckling of the metal layers. Final failure for both materials involved complete separation of layers caused by out of plane deformation. The ultimate bearing stress and strain were significantly higher for GLARE® 2 than for GLARE® 3, which the micrographs indicate is due to the higher bending stiffness of the reinforcing layers in GLARE® 2, which delays out of plane deformation during the final failure sequence. Measurements of surface strains showed similar initial behaviour for both materials, in agreement with the analysis of the bearing stress–strain curves, and provided additional insight into the final failure sequence of the two materials.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Mechanical Behavior of Composites · Textile materials and evaluations · Optical measurement and interference techniques

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (17)

Show source-provided references
1. Towards application of fibre metal laminates in large aircraft10.1108/00022669910303711 ↗
2. GLARE technology development 1997–200010.1023/A:1016006314630 ↗
3. Development of fibre metal laminates for advanced aerospace structures10.1016/S0924-0136(00)00411-8 ↗
4. An historic overview of the development of fibre metal laminates10.1023/A:1025533701806 ↗
5. Vlot · 2001
6. Impact loading on fibre metal laminates10.1016/0734-743X(96)89050-6 ↗
7. Modelling of bird strike on an aircraft wing leading edge made from fibre metal laminates. Part 1. Material modelling10.1023/B:ACMA.0000037133.64496.13 ↗
8. Modelling of bird strike on an aircraft wing leading edge made from fibre metal laminates. Part 2. Modelling of impact with SPH bird model10.1023/B:ACMA.0000037134.93410.c0 ↗
9. The mechanical behavior of GLARE laminates for aircraft structures10.1007/s11837-005-0067-4 ↗
10. Parametric studies of bearing strength for fibre metal laminates10.2514/3.46582 ↗
11. Van Rooijen RGJ. Bearing strength characteristics of standard and steel reinforced GLARE. PhD Thesis. Delft University of Technology, Department of Aerospace Engineering; 2006.
12. On bearing strength of fibre metal laminates10.1177/002199839202601705 ↗
13. Observations on bolted connections in composite structures10.1016/0263-8223(89)90051-2 ↗
14. Pin and bolt bearing strength of fibreglass/aluminium laminates10.1016/j.compositesa.2005.01.014 ↗
15. Prediction of bearing strength in fiber metal laminates10.1177/0021998306067302 ↗
16. Failure mechanisms in bolted CFRP10.1177/073168449801700302 ↗
17. Bolt-hole clearance effects and strength criteria in single-bolt, single-lap, composite bolted joints10.1016/S0266-3538(02)00088-X ↗