journal article·2021-07

A parametric study on static behavior and load sharing of multi-bolt hybrid bonded/bolted composite joints

Valentin S. Romanov, Mohammad Heidari-Rarani, Larry Lessard

Publisher page

Abstract

Abstract The combination of two joining mechanisms – bonding and bolting – in a single hybrid joint may potentially result in a stronger and more durable joint than either of the separate constituents. Studies have shown that the load sharing between the adhesive and the bolt is a key parameter for such an improvement. The present work executes a parametric study on single-lap hybrid bonded/bolted composite joints with multiple bolts. Joints of five different geometric configurations are subjected to the static tensile loading. The experimental study is supported by modeling results. The study reveals a significant influence of the joint overlap length on the joint strength. The impact of the bolt positioning is less pronounced. Joint stiffness is shown to be mainly governed by the joint overlap length. The load sharing between the adhesive and the bolts is shown to be geometry-dependent, i.e., facilitated by a shorter joint overlap length and smaller bolt-edge distance. The overlap area is shown to be a dominant factor for the strength improvement over that of the load sharing. However, providing that the overlap area is kept unchanged, enhanced load sharing leads to a higher joint strength, revealing their non-linear relationship.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Mechanical Behavior of Composites · Structural Load-Bearing Analysis · Mechanical stress and fatigue analysis

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (44)

Show source-provided references
1. Simplified procedures for designing composite bolted joints10.1177/073168449000900607 ↗
2. Tensile strength of open-hole, pin-loaded and multi-bolted single-lap joints in woven composite plates10.1016/j.matdes.2015.09.008 ↗
3. Investigation of bolt group configurations on load distribution and joint failure10.1080/15376494.2012.697604 ↗
4. An analytical model for strength prediction in multi-bolt composite joints at various loading rates10.1016/j.compstruct.2014.05.021 ↗
5. Review on adhesive joints and their application in hybrid composite structures10.1080/01694243.2018.1543528 ↗
6. Review on techniques to improve the strength of adhesive joints with composite adherends10.1016/j.compositesb.2019.107363 ↗
7. Mode-I behavior of adhesively bonded composite joints at high loading rates10.1016/j.compscitech.2020.108310 ↗
8. The detectability of kissing bonds in adhesive joints using ultrasonic techniques10.1016/S0041-624X(03)00156-2 ↗
9. A review of defect types and nondestructive testing techniques for composites and bonded joints
10. Non-destructive examination of adhesively bonded structures using dielectric techniques: review and some results10.1243/0954406001522831 ↗
11. Hygrothermal effects on the strength of adhesively bonded joints10.1163/156856198X00425 ↗
12. Hart-Smith · 1982
13. Load transfer in hybrid (bonded/bolted) composite single-lap joints10.1016/j.compstruct.2004.04.016 ↗
14. Investigation of bolted/bonded composite joint behaviour using design of experiments10.1016/j.compstruct.2017.02.084 ↗
15. Mechanical characterization of a flexible epoxy adhesive for the design of hybrid bonded-bolted joints10.1016/j.polymertesting.2019.106048 ↗
16. Experimental investigations of bolted, adhesively bonded and hybrid bolted/bonded single-lap joints in composite laminates10.1016/j.mtcomm.2020.101244 ↗
17. Tensile properties of a hybrid bonded/bolted joint: parameter study: parameter study10.1016/j.compstruct.2020.112329 ↗
18. Fatigue of hybrid (adhesive/bolted) joints in SRIM composites10.1016/S0143-7496(00)00047-6 ↗
19. Quasi-static strength and fatigue life of hybrid (bonded/bolted) composite single-lap joints10.1016/j.compstruct.2004.11.002 ↗
20. Evolution of mechanical properties of flexible epoxy adhesives under cyclic loading and its effects on composite hybrid bolted/bonded joint design10.1016/j.compstruct.2018.01.049 ↗
21. Hybrid bonded-fastened joints and their application in composite structures: a general review10.1177/0731684415627296 ↗
22. Load sharing in single-lap bonded/bolted composite joints. Part I: model development and validation10.1016/j.compstruct.2015.04.040 ↗
23. An analytical model for the strength prediction of hybrid (bolted/bonded) composite joints10.1016/j.compstruct.2012.10.022 ↗
24. Load sharing in single-lap bonded/bolted composite joints. Part II: global sensitivity analysis10.1016/j.compstruct.2015.03.069 ↗
25. Effect of adhesive layer compliance on strength of single-lap hybrid bonded-bolted joints
26. Improving load sharing in hybrid bonded/bolted composite joints using an interference-fit bolt10.1016/j.compstruct.2016.04.025 ↗
27. Nonlinear static analysis of a composite bonded/bolted single-lap joint using the meshfree radial point interpolation method10.1016/j.compstruct.2015.08.136 ↗
28. Progressive damage analysis of multi-bolt composite joints with variable bolt–hole clearances10.1016/j.compositesb.2004.11.003 ↗
29. Simulation of single-lap bonded and hybrid (bolted/bonded) joints with flexible adhesive10.1016/j.ijadhadh.2009.12.002 ↗
30. Dimensioning method for bolted, adhesively bonded, and hybrid joints involving Fibre-Reinforced-Polymers10.1016/j.compositesb.2012.09.074 ↗
31. Static and fatigue testing bolted, bonded and hybrid step lap joints of thick carbon fibre/epoxy laminates used on aircraft structures10.1016/j.compstruct.2016.01.078 ↗
32. Experimental and finite element studies of bolted, bonded and hybrid step lap joints of thick carbon fibre/epoxy panels used in aircraft structures10.1016/j.compositesb.2016.06.061 ↗
33. Experimental and finite element studies of thin bonded and hybrid carbon fibre double lap joints used in aircraft structures10.1016/j.compositesb.2015.09.038 ↗
34. Simplified stress analysis of hybrid (bolted/bonded) joints10.1016/j.ijadhadh.2017.05.003 ↗
35. Tensile behavior of hybrid multi-bolted/bonded joints in composite laminates10.1016/j.ijadhadh.2019.102426 ↗
36. 2007
37. ASTM Standard D3165-07 · 2007
38. Technical data sheet of CYCOM® 5320-1 Prepreg
39. Bodjona · 2016
40. Romanov · 2017
41. Strength and fatigue life modeling of bonded joints in composite structure10.1520/CTR10569J ↗
42. Failure of composite laminates containing pin loaded holes-Method of solution10.1177/002199838401800305 ↗
43. The effect of laminate configuration on characteristic lengths and rail shear strength10.1177/002199838401800307 ↗
44. Influence of end distances on the failure of composite bolted joints10.1177/0731684415572199 ↗