Influence of cooling condition on properties of extruded aluminum alloy matrix composites
Source abstract
Abstract
Abstract This paper discusses the influence of applying water cooling after extrusion on the stability of mechanical properties on the AA6061-7.5 vol. % SiC composite rods cross section. The materials were prepared via powder metallurgy processing using extrusion with a reversibly rotating die at the last technological stage. The mechanical properties, texture and microstructure of composites were analyzed following the experiment. In both deformed samples the XRD measurements indicated that the was the predominant orientation, which, however, was weaker towards the edge of the specimen. Moreover, some differences in microhardness between the center and the edge of water cooled rod were observed.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Aluminum Alloys Composites Properties · Aluminum Alloy Microstructure Properties · Metallurgy and Material Forming
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (24)
Show source-provided references
1. Influence of extrusion ratio on the mechanical behavior of AA6061/SiC composites
2. Ductility and strength of extruded SiCp/aluminium-alloy composites10.1016/S0266-3538(01)00198-1 ↗
3. Clad-extrusion for producing SiCw/6061Al composite tubes10.1023/A:1017990816776 ↗
4. Effect of reinforcement volume fraction on the evolution of reinforcement size during the extrusion of Al-SiC composite10.1016/S0921-5093(01)01526-X ↗
5. Effects of hot extrusion parameters on the tensile properties and microstructures of SiCw-2124Al composites10.1016/0921-5093(95)09996-4 ↗
6. Influence of mixing parameters on homogeneity of Al/SiC composites10.2478/amm-2014-0254 ↗
7. Effects of hot extrusion parameters on the tensile properties and microstructures of SiCw-2124A1 composites10.1016/0921-5093(95)09996-4 ↗
8. Forming of aluminium alloy at temperatures just below melting point10.1016/S0890-6955(02)00242-0 ↗
9. Extrusion of AlMgSi alloys
10. Damage development of Al/SiC metal matrix composite under fatigue, creep and monotonic loading conditions10.1016/j.proeng.2011.04.236 ↗
11. Evaluation of change in material properties due to plastic deformation10.1016/j.jmatprotec.2004.04.114 ↗
12. Effect of texture on the mechanical properties and ballistic performance of an extruded Al-6063 rod
13. Saha · 2000
14. Evolution of surface recrystallization during indirect extrusion of 6xxx aluminum alloys10.1007/s11661-005-0298-6 ↗
15. Korbel A, Bochniak W. Method of plastic forming of materials, U.S. Patent No. 5,737,959, 1997.
16. KOBO type forming: forging of metals under complex conditions of the process10.1016/S0924-0136(02)01033-6 ↗
17. New structural and mechanical features of hexagonal materials after room temperature extrusion using the KoBo method10.3139/146.110490 ↗
18. Plastic flow of aluminium extruded under complex conditions10.1179/026708300101508243 ↗
19. A direct method of determining preferred orientation of a flat reflection sample using a geiger counter X-Ray spectrometer10.1063/1.1698268 ↗
20. A characterization for the dynamic recrystallization kinetics of as-extruded 7075 aluminum alloy based on true stress-strain curves10.1016/j.commatsci.2011.11.031 ↗
21. Microstructural analysis of the <111> and <110> nickel single crystals subjected to severe plastic deformation by hydroextrusion10.1016/j.msea.2012.11.093 ↗
22. Microstructure and texture development in Ag-Cu alloys subjected to severe plastic deformation
23. An experimental determination of the yield locus for titanium and titanium-alloy sheet
24. Modeling of texture evolution in KOBO extrusion process10.2478/v10172-012-0160-y ↗