Mechanical properties and lightweight design of FDM-produced fiber-reinforced composite structures
Source abstract
Abstract
This study systematically investigated the synergistic effects of nozzle diameter and infill geometry on the mechanical properties and lightweight potential of short carbon fiber-reinforced ABS composites fabricated by fused deposition modeling (FDM). Sandwich specimens were produced with three nozzle diameters (0.4, 0.6, and 0.8 mm) and four infill patterns: Gyroid, 2D-honeycomb, 3D-honeycomb, and solid. Three-point flexural tests revealed that increasing the nozzle diameter from 0.4 mm to 0.8 mm significantly enhanced interlayer bonding, leading to a maximum improvement of 21.7% in flexural strength (Gyroid) and 25.3% in flexural modulus (solid infill). At 50% infill density, the 3D-honeycomb structure exhibited superior performance, with 4.7%-19.5% higher flexural strength and 2.89%-20.4% higher modulus than other infill types. Notably, the mass-normalized analysis highlighted the Gyroid structure as the most efficient in material utilization. With a 0.8 mm nozzle system, the strength could reach 14.11 MPa/g and the modulus could reach 574.24 MPa/g, highlighting its unique lightweight potential. Microscopic crack observations further elucidated the distinct failure mechanisms governed by the interplay between nozzle diameter and infill architecture. This work provided a comprehensive understanding of the process-structure-performance relationship in FDM-fabricated composites, offering practical guidelines for parameter selection in automotive lightweight applications.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Additive Manufacturing and 3D Printing Technologies · Fiber-reinforced polymer composites · Mechanical Behavior of Composites
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Dalian Jiaotong University
References (35)
Show source-provided references
1. 10.1016/j.promfg.2017.07.14810.1016/j.promfg.2017.07.148 ↗
2. Ahmad MN, Ishak MR, Maidin NA, et al. Water absorption analysis of oil palm fibre reinforced acrylonitrile butadiene styrene composites by fick’s law. Journal of advanced research in experimental fluid mechanics and heat transfer 2025; 20(1): 150–158. https://doi.org/10.37934/arefmht.20.1.150158
3. 10.1016/j.addma.2014.08.00510.1016/j.addma.2014.08.005 ↗
4. 10.1007/s40964-021-00192-410.1007/s40964-021-00192-4 ↗
5. 10.1016/j.addma.2020.10138510.1016/j.addma.2020.101385 ↗
6. Jin Y, He Y, Fu J, et al. Optimization of tool-path generation for material extrusion-based additive manufacturing technology. Addit Manuf 2014; 1: 32–47. https://doi.org/10.1016/j.addma.2014.08.004
7. 10.1016/j.jmapro.2022.09.03210.1016/j.jmapro.2022.09.032 ↗
8. 10.1007/s00170-018-03269-710.1007/s00170-018-03269-7 ↗
9. 10.1080/15376494.2024.239154510.1080/15376494.2024.2391545 ↗
10. 10.1007/s00170-019-04839-z10.1007/s00170-019-04839-z ↗
11. 10.3390/polym1104065610.3390/polym11040656 ↗
12. 10.1016/j.pmatsci.2023.10122110.1016/j.pmatsci.2023.101221 ↗
13. 10.1016/j.addma.2017.06.00410.1016/j.addma.2017.06.004 ↗
14. 10.1016/j.addma.2019.03.00810.1016/j.addma.2019.03.008 ↗
15. 10.1115/1.405037210.1115/1.4050372 ↗
16. 10.1016/j.compositesb.2019.01.08510.1016/j.compositesb.2019.01.085 ↗
17. 10.1016/j.conbuildmat.2024.13910510.1016/j.conbuildmat.2024.139105 ↗
18. 10.1007/s00170-025-15961-610.1007/s00170-025-15961-6 ↗
19. 10.1016/j.compscitech.2014.10.00910.1016/j.compscitech.2014.10.009 ↗
20. 10.1007/s11664-015-3687-710.1007/s11664-015-3687-7 ↗
21. 10.1016/j.compositesb.2019.04.02910.1016/j.compositesb.2019.04.029 ↗
22. 10.3390/jcs910054810.3390/jcs9100548 ↗
23. 10.1007/s00158-018-1994-310.1007/s00158-018-1994-3 ↗
24. 10.1016/j.oceaneng.2024.11760110.1016/j.oceaneng.2024.117601 ↗
25. 10.3390/polym1212279210.3390/polym12122792 ↗
26. 10.1007/s11831-019-09331-110.1007/s11831-019-09331-1 ↗
27. 10.1016/j.matdes.2018.01.02310.1016/j.matdes.2018.01.023 ↗
28. 10.1016/j.matdes.2017.03.01810.1016/j.matdes.2017.03.018 ↗
29. 10.1016/j.promfg.2017.09.14610.1016/j.promfg.2017.09.146 ↗
30. 10.1108/RPJ-10-2020-025010.1108/RPJ-10-2020-0250 ↗
31. 10.1108/RPJ-08-2020-018510.1108/RPJ-08-2020-0185 ↗
32. Fischer D, Eßbach C, Schönherr R, et al. Improving inner structure and properties of additive manufactured amorphous plastic parts: the effects of extrusion nozzle diameter and layer height. Addit Manuf 2022; 51: 102596. https://doi.org/10.1016/j.addma.2022.102596
33. Roschli A, Gaul KT, Boulger AM, et al. Designing for big area additive manufacturing. Addit Manuf 2019; 25: 275–285. https://doi.org/10.1016/j.addma.2018.11.006
34. Go J, Hart AJ. Fast desktop-scale extrusion additive manufacturing. Addit Manuf 2017; 18: 276–284. https://doi.org/10.1016/j.addma.2017.10.016
35. Schuller T, Jalaal M, Fanzio P, et al. Optimal shape design of printing nozzles for extrusion-based additive manufacturing. Addit Manuf 2024; 84: 104130. https://doi.org/10.1016/j.addma.2024.104130