journal article·2009-08

Geometrically Nonlinear Determination of Energy Release Rate and Mode Ratio in Single Leg Bending Tests

B.D. Davidson, Amitabh Bansal, Qida Bing, Xuekun Sun

Publisher page

Abstract

Geometrically linear and nonlinear finite element analyses are used to determine the energy release rate and mode ratio in simulated tests of unidirectional, symmetric, single leg bending (SLB) specimens. It is shown that the finite diameter loading rollers that are typically used in practical test set-ups cause this test to be inherently nonlinear. The differences between the linear and nonlinear results are presented parametrically as a function of material properties, specimen thickness, roller diameter, span length and crack length. These results are used, along with empirically derived equations, to develop an approach for designing SLB experiments where one will have a high degree of confidence in toughness values as obtained from conventional data reduction techniques, and for which relatively little specimen-to-specimen variation in mode ratio will be observed.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Mechanical Behavior of Composites · Fatigue and fracture mechanics · Structural Health Monitoring Techniques

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Department of Mechanical and Aerospace Engineering, Syracuse University Syracuse, NY 13244, USA,

Department of Mechanical and Aerospace Engineering, Syracuse University Syracuse, NY 13244, USA

References (26)

Show source-provided references
1. 10.1007/BF0003452510.1007/BF00034525 ↗
2. Davidson, B.D. · ASTM STP · 1997 · 1242 · 109
3. Davidson, B.D. · Sci. Technol. · 2006 · 66 · 1479
4. Bhashyam, S. and Davidson, B.D. (1997). Evaluation of Data Reduction Methods for the Mixed-Mode Bending Test, AIAA J., 35(3): 546-552.10.2514/2.129 ↗
5. Szekrenyes, A. · Sci. Technol. · 2004 · 64 · 2393
6. Szekrenyes, A. · Struct. · 2006 · 72 · 321
7. 10.1520/CTR10849J10.1520/CTR10849J ↗
8. 10.1007/BF0001812910.1007/BF00018129 ↗
9. 10.1177/07316844930120120410.1177/073168449301201204 ↗
10. 10.1177/00219983950290150210.1177/002199839502901502 ↗
11. 10.1016/0010-4361(95)90878-410.1016/0010-4361(95)90878-4 ↗
12. Korjakin, A. · Composite · 1998 · 19 · 793
13. 10.1177/00219983980320170110.1177/002199839803201701 ↗
14. ASTM D6671-01. · ASTM International
15. 10.1177/002199830606730410.1177/0021998306067304 ↗
16. 10.1177/073168440505040210.1177/0731684405050402 ↗
17. 10.1007/s10704-005-3746-910.1007/s10704-005-3746-9 ↗
18. 10.1177/002199830607103110.1177/0021998306071031 ↗
19. 10.1115/1.289593110.1115/1.2895931 ↗
20. 10.1016/0013-7944(77)90013-310.1016/0013-7944(77)90013-3 ↗
21. 10.1177/00219983950290060110.1177/002199839502900601 ↗
22. Kanninen, M.F. · Int. J. Fracture · 1973 · 9 · 8310.1007/BF00035958 ↗
23. Williams, J.G. · Sci. Technol. · 1989 · 35 · 367
24. Davidson, B.D. and Krafchak, T.M. (1993). Analysis of Instability-related Delamination Growth Using a Crack Tip Element, AIAA J., 31(11): 2130-2136.10.2514/3.11900 ↗
25. 10.1016/j.engfracmech.2005.11.00710.1016/j.engfracmech.2005.11.007 ↗
26. Davidson, B.D. · J. ASTM Inter. · 2006 · 3 · 110.1520/JAI100285 ↗