journal article·2026-05

Process optimization of compressive property and dimensional error on wood polylactic acid gyroid-structured polymer composite

Dhinakaran Veeman, Sabarinathan Palaniyappan, GJ Surendhar, Ragavanantham Shanmugam

Publisher page

Abstract

In the fused deposition modeling (FDM) process, various thermoplastic filaments may be used as a feedstock material for the component fabrication. The present study involves incorporating a gyroid structure in wood/polylactic acid (PLA) polymer composite. The strength of the sample may reduce while incorporating lattice structure in PLA polymeric samples. There are certain difficulties due to the wide availability of process parameters that may vary the quality and strength during the fabrication of the sample through the FDM process. Determining the influence of certain important process parameters such as raster angle, layer thickness, and wall thickness is carried out in this research to attain higher mechanical strength and less dimensional error in the geometry of the fabricated sample. Taguchi L 9 orthogonal array is used in these experiments to optimize process parameters in the gyroid incorporated samples. The output responses in the present study are compressive strength and dimensional error. Both the output responses were predicted using the ANOVA technique. Both the output responses are greatly influenced by the raster angle with the value of 60.78% in compressive strength and 90.43% in the dimensional error, and Wall thickness is the least influenced process parameter with the value of 7.17% in compressive strength and 0.93% in dimensional error. The sequential order of influencing process parameters in both the compressive strength and dimensional error were raster angle > layer thickness > wall thickness. 31.019 MPa of compressive strength was observed in the confirmational compression test. The prepared composite can be used as a structural material in the replacement of balusters and handrails.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Additive Manufacturing and 3D Printing Technologies · Manufacturing Process and Optimization · Innovations in Concrete and Construction Materials

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Chennai Institute of Technology

Navajo Technical University

Funding

Chennai Institute of Technology

References (41)

Show source-provided references
1. Wong KV, Hernandez A. A review of additive manufacturing. Int Sch Res Notices 2012; 2012.
2. Gibson I, Rosen DW, Stucker B, et al. Addit. Manuf. Tech. Cham, Switzerland: Springer, 2021.
3. 10.1016/j.matdes.2015.06.05310.1016/j.matdes.2015.06.053 ↗
4. 10.1007/s13369-022-06806-510.1007/s13369-022-06806-5 ↗
5. Elkholy A Kempers R. Investigation into the Influence of Fused Deposition Modeling (FDM) Process Parameters on the Thermal Properties of 3D-Printed Parts. In: Proceedings of the 2018 Canadian Society for Mechanical Engineering (CSME) International Congress. Toronto ON: Canada; 2018.10.25071/10315/35337 ↗
6. 10.1007/s00170-016-9263-310.1007/s00170-016-9263-3 ↗
7. 10.1007/s11837-015-1367-y10.1007/s11837-015-1367-y ↗
8. 10.1108/1355254061065244710.1108/13552540610652447 ↗
9. 10.1016/j.jmatprotec.2005.02.25910.1016/j.jmatprotec.2005.02.259 ↗
10. 10.1108/RPJ-09-2013-008610.1108/RPJ-09-2013-0086 ↗
11. 10.1016/j.jmapro.2018.09.02510.1016/j.jmapro.2018.09.025 ↗
12. 10.1108/1355254071082481410.1108/13552540710824814 ↗
13. 10.1016/j.addma.2017.11.00410.1016/j.addma.2017.11.004 ↗
14. 10.1016/j.ijmecsci.2020.10576710.1016/j.ijmecsci.2020.105767 ↗
15. 10.1016/j.rineng.2021.10026410.1016/j.rineng.2021.100264 ↗
16. 10.1016/j.matpr.2020.11.33210.1016/j.matpr.2020.11.332 ↗
17. 10.1002/pc.2562110.1002/pc.25621 ↗
18. 10.1007/s10163-019-00927-010.1007/s10163-019-00927-0 ↗
19. 10.1007/s12633-022-01712-910.1007/s12633-022-01712-9 ↗
20. 10.1080/10667857.2021.191505610.1080/10667857.2021.1915056 ↗
21. 10.1007/s00170-021-08289-410.1007/s00170-021-08289-4 ↗
22. 10.1016/j.matpr.2019.08.15810.1016/j.matpr.2019.08.158 ↗
23. 10.1016/j.matdes.2016.05.02010.1016/j.matdes.2016.05.020 ↗
24. 10.1016/j.jmbbm.2017.04.01110.1016/j.jmbbm.2017.04.011 ↗
25. 10.1016/j.matdes.2017.02.02110.1016/j.matdes.2017.02.021 ↗
26. 10.1016/j.jmbbm.2017.08.03410.1016/j.jmbbm.2017.08.034 ↗
27. Magerramova L, Volkov M, Afonin A, et al. Application of light lattice structures for gas turbine engine fan blades. In: Proccedings of the 31st Congress of the International Council of the Aeronautical Sciences, ICAS 2018.
28. 10.3390/app918384410.3390/app9183844 ↗
29. 10.1016/j.jmbbm.2019.05.01910.1016/j.jmbbm.2019.05.019 ↗
30. 10.1016/j.ijsolstr.2014.06.02410.1016/j.ijsolstr.2014.06.024 ↗
31. 10.1016/j.matdes.2019.10759710.1016/j.matdes.2019.107597 ↗
32. Abidin Zainal YanisKadir M.M. Zahri Akbar Teguh P et al. Optimization of FDM 3D printing process parameter for improving porosity accuracy of PLA Scaffold. In: 4th Forum in Research Science and Technology. Atlantis Press; 2021 pp. 155–161. (FIRST-T1-T2-2020).10.2991/ahe.k.210205.028 ↗
33. 10.1016/j.compstruct.2019.03.01010.1016/j.compstruct.2019.03.010 ↗
34. Karna SK, Sahai R. An overview on Taguchi method. Int J Eng Math 2012; 1(1): 1–7.
35. 10.1016/j.matpr.2020.02.43510.1016/j.matpr.2020.02.435 ↗
36. 10.1177/089270572096456010.1177/0892705720964560 ↗
37. Rodríguez P Zapico P Robles PE et al. Evaluation of mechanical properties of FDM components reinforced with fibre. In: IOP Conferences Series: Materials Science and Engineering 1193. IOP Publishing 2021 p. 012069. No. 1.10.1088/1757-899X/1193/1/012069 ↗
38. 10.1007/s11665-021-05809-x10.1007/s11665-021-05809-x ↗
39. 10.1016/j.matpr.2018.08.16710.1016/j.matpr.2018.08.167 ↗
40. 10.1177/0892705722108983210.1177/08927057221089832 ↗
41. 10.1007/s12633-020-00466-610.1007/s12633-020-00466-6 ↗