journal article·2018-02

Failure modes and failure mechanisms of single tooth bound to composite pre-tightened tooth connection

Yifeng Gao, Fei Li, Qilin Zhao, Jiangang Gao, Xiaoqiang Yan, Longxing Xu

Publisher page

Abstract

To assess the failure modes and failure mechanisms of single pre-tightened tooth connection joints, experiments were conducted on the mechanical properties of three different materials―T700/DER-321, T700/EP4221, and E-glass/HCH-8300―under different geometric parameters. During the test, failure processes and details of the fracture surfaces were observed by using a high-speed camera, an optical microscope, and a scanning electron microscope. Then, the failure modes and failure mechanisms of the joints were analyzed by numerical simulation and theoretical methods. The results showed that only two failure modes, shear failure and crushing failure, occurred in the glass fiber-reinforced plastic single joint. However, in addition to these two failure modes, a new failure mode was found to occur in the carbon fiber-reinforced plastic single joint, i.e. compression failure. The glass fiber-reinforced plastic joint had a lower elastic modulus along the fiber direction than the carbon fiber-reinforced plastic joint, which was the fundamental cause for the new failure mode. The carbon fiber-reinforced plastic joint with compression failure had a higher bearing capacity, and a certain ductile failure will occur as a result of the large interlaminar shear strength of the composite, which is an important consideration in joint design. Thus, the material type, the geometrical parameters of the tooth, and the interlaminar shear strength of the composite all influenced the failure modes and the bearing capacity of single pre-tightened tooth connection joints.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Mechanical Behavior of Composites · Mechanical stress and fatigue analysis · Fatigue and fracture mechanics

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Engineering Institute of Engineer Corps, PLA University of Science and Technology, Nanjing, China

Engineering Management Department, Institute of Logistics Engineering of PLA, Chongqing, China

College of Mechanical and Power Engineering, Nanjing University of Technology, Nanjing, China

The First Research Division, General Equipment Department of the PLA, Wuxi, China

Funding

National Natural Science Foundation of China · Natural Science Foundation of Jiangsu Province

References (19)

Show source-provided references
1. Zhao Q, Chen H, andLi F. Composite tube connection technology. Patent zl.201020157303.1, China, 2010.
2. Xu L, Cheng Y, Chen L, et al. Research on bearing capacity and shear stress distribution of composite pre-tightened teeth connection in tension and compression. J Reinf Plast Compos 2015; 6: 2300–28.
3. 10.1177/073168441349257510.1177/0731684413492575 ↗
4. Zhao Q · Fibre Reinf Plast/Compos · 2014 · 12 · 52
5. 10.1177/073168441558893510.1177/0731684415588935 ↗
6. 10.1177/073168441557943710.1177/0731684415579437 ↗
7. Liu J · Acta Mater Compos Sin · 2016 · 33 · 2215
8. 10.1016/j.compstruct.2013.09.05810.1016/j.compstruct.2013.09.058 ↗
9. Liu PF · Sci World J · 2014 · 10 · 125
10. 10.1177/136943321562715810.1177/1369433215627158 ↗
11. 10.1177/136943321665619610.1177/1369433216656196 ↗
12. Xu L. Research on bearing capacity calculation and experiment of composite tubes pre-tightened teeth . Master Thesis, Engineering Institute of Engineer Corps, PLA University of Science and Technology, China, 2015.
13. 10.1016/j.compstruct.2016.06.03610.1016/j.compstruct.2016.06.036 ↗
14. Li F. Research on new type of pultruded composite connection and application in the truss . PhD Thesis, Engineering Institute of Engineer Corps, PLA University of Science and Technology, China, 2012.
15. 10.1016/j.compscitech.2006.12.00110.1016/j.compscitech.2006.12.001 ↗
16. 10.1177/00219983740080030310.1177/002199837400800303 ↗
17. 10.1177/00219983780120030210.1177/002199837801200302 ↗
18. 10.1177/00219983780120030510.1177/002199837801200305 ↗
19. 10.1177/00219983710050010610.1177/002199837100500106 ↗