journal article·2024-05

A study of post-processing for AFP-fabricated thermoplastic composites with void content and air permeability characterization

Sasan Karimi, Pouya Y Louyeh, Ali Barzegar, Mehmet Yildiz, Hatice S Sas

Publisher page

Abstract

Improving the quality of fiber-reinforced composite laminates using out-of-autoclave techniques has been a challenge for a long time. The recent trends toward the replacement of autoclave processes with out-of-autoclave processes for thermoplastic composites still lack a compressive recipe. This study first develops an understanding of the integrated effect of the automated fiber placement (AFP) lay-up process parameters (compaction force and lay-up velocity) and the type of post-processing: i) autoclave and ii) vacuum bag only (VBO) processing with two vacuum hold times, 2 and 24 h. The void content results highlight the potential of the VBO process to replace the autoclave with an improved void content of VBO with 24 vacuum hold times. Then, this result has been correlated with the morphology of voids after the AFP lay-up as isolated or connected via air permeability characterization. This study reveals that the high air permeability to effective porosity ratio of samples after AFP lay-up which is achievable with low compaction force facilitates the air removal mechanism during the VBO process with sufficient vacuum hold times.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Epoxy Resin Curing Processes · Mechanical Behavior of Composites · Composite Material Mechanics

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Integrated Manufacturing Technologies Research and Application Center, Sabanci University, Istanbul, Turkey

Composite Technologies Center of Excellence, Sabanci University-Kordsa, Istanbul Technology Development Zone, Istanbul, Turkey

Faculty of Engineering and Natural Sciences, Department of Manufacturing Engineering, Sabanci University, Istanbul, Turkey

Funding

Sabancı Üniversitesi · Türkiye Bilimsel ve Teknolojik Araştirma Kurumu

References (39)

Show source-provided references
1. 10.1016/j.jcomc.2021.10018210.1016/j.jcomc.2021.100182 ↗
2. 10.2514/6.2019-051610.2514/6.2019-0516 ↗
3. 10.1016/j.compositesa.2014.09.02910.1016/j.compositesa.2014.09.029 ↗
4. 10.1177/089270572094537610.1177/0892705720945376 ↗
5. 10.1016/j.compositesb.2022.11040510.1016/j.compositesb.2022.110405 ↗
6. 10.3390/polym1312195110.3390/polym13121951 ↗
7. 10.1177/09673911100180010110.1177/096739111001800101 ↗
8. 10.1177/00219980303518810.1177/002199803035188 ↗
9. Lamontia MA · 30th Int SAMPE Eur Conf · 2009 · 2009 · 1
10. 10.1177/002199831244181010.1177/0021998312441810 ↗
11. 10.1080/20550340.2015.111479810.1080/20550340.2015.1114798 ↗
12. 10.1016/j.compositesa.2017.02.00810.1016/j.compositesa.2017.02.008 ↗
13. Di Francesco M · ECCM 2016-Proceeding 17th Eur Conf Compos Mater · 2016
14. 10.1016/j.compositesb.2014.05.02510.1016/j.compositesb.2014.05.025 ↗
15. 10.1016/j.compositesa.2020.10616010.1016/j.compositesa.2020.106160 ↗
16. 10.1016/j.compositesa.2013.03.00310.1016/j.compositesa.2013.03.003 ↗
17. 10.1016/j.compscitech.2018.02.03110.1016/j.compscitech.2018.02.031 ↗
18. Vernejoux C, Fischer X, Deseur S, et al. Influence of automated fiber placement parameters on thermoplastic composite blanks used on stamp forming process. In: ESAFORM 2021. Liège (virtual), Belgium 2021: 1–11.10.25518/esaform21.366 ↗
19. 10.1016/j.compositesa.2014.09.02910.1016/j.compositesa.2014.09.029 ↗
20. 10.3390/ma1502045110.3390/ma15020451 ↗
21. Cender TA · International SAMPE Technical Conference · 2014
22. 10.1016/j.compositesa.2019.03.03510.1016/j.compositesa.2019.03.035 ↗
23. 10.1016/j.compscitech.2019.01.03010.1016/j.compscitech.2019.01.030 ↗
24. 10.1016/j.compositesb.2019.10732010.1016/j.compositesb.2019.107320 ↗
25. 10.1007/s11242-016-0784-x10.1007/s11242-016-0784-x ↗
26. 10.1016/j.compositesa.2013.02.01310.1016/j.compositesa.2013.02.013 ↗
27. 10.1177/002199831771508910.1177/0021998317715089 ↗
28. Zhang D · 2017
29. 10.1177/002199831770070010.1177/0021998317700700 ↗
30. Zhang D, Heider D, Gillespie JWJr. Volatile removal during out of autoclave processing of high performance thermoplastic composites. In: CAMX - 2014. Orlando, FL 2014.
31. Toray. Toray Cetex ® TC1320 PEKK product data sheet 2019; 31: 1–3.10.1016/S0958-2118(19)30195-8 ↗
32. 10.1177/0731684422114344810.1177/07316844221143448 ↗
33. 10.1016/j.compositesa.2015.04.00910.1016/j.compositesa.2015.04.009 ↗
34. Paciornik S · Materia · 2010 · 15 · 172
35. 10.1016/j.compositesa.2017.06.01310.1016/j.compositesa.2017.06.013 ↗
36. 10.1038/nmeth.201910.1038/nmeth.2019 ↗
37. Klinkenberg LJ · Drill Prod Pract · 2012 · 200
38. 10.1016/j.compositesa.2020.10616010.1016/j.compositesa.2020.106160 ↗
39. 10.1016/j.procir.2017.03.22010.1016/j.procir.2017.03.220 ↗