Weld line strength factors in a reinforced injection molded part: Relationship with predicted fiber orientation
Source abstract
Abstract
In this work, the residual strength of a fiber-reinforced injection molded part containing a hot weld line—or meld line—was evaluated. Injected plates were generated using a double-gated mold under four different process conditions. Quantification of the weld line detrimental effect was made in base on a fracture mechanics experiment. Specimens with and without the weld line—obtained from the same plates—were tested under a clamped single edge notched tension (SENT) configuration. For each set of process conditions, a relative weld line strength factor was defined in terms of the maximum applied stress intensity factor (K Imax ) as: K Imax of specimens with weld line/K Imax of specimens without weld line. In parallel, the fiber distribution pattern was obtained by process simulation software Moldex3D. An orientation factor was determined from simulation in order to quantify the effect of the local fiber orientation around the weld line. Optimal process condition and the most significant variable influencing the weld line strength were calculated via statistical analysis. Results showed a clear correlation between the weld line strenght factors and the orientaion factor. It was demonstrated that the fracture performance of the weld line region is controlled by the fiber orientation arrangement developed on that zone.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Injection Molding Process and Properties · Advanced machining processes and optimization · Manufacturing Process and Optimization
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Instituto de Investigaciones en Ciencia y Tecnología de Materiales (INTEMA), Universidad Nacional de Mar del Plata, Buenos Aires, Argentina
References (39)
Show source-provided references
1. 10.1016/j.egypro.2013.06.81210.1016/j.egypro.2013.06.812 ↗
2. Hamada H, Yamada K, Tomari K, et al. Fracture behavior of injection moldings with weld lines, http://www.gruppofrattura.it (2013, accessed 10 May 2018).
3. Kuehnert I, Spoerer Y, Zimmermann M. Weld lines in injection molded parts: Strength, morphology and improvement. In: SPE ANTEC , Indianapolis, IN, 23–25 May 2016, paper no. 1255.
4. BASF Corporation. Mechanical performance of knit lines and welded butt joints – A key factor in designing of multiple gated injection molded and subsequent welded thermoplastic c omponents . Florham Park, NJ: BASF Corporation, 2003.
5. 10.1002/pc.2018210.1002/pc.20182 ↗
6. 10.1007/BF0295436710.1007/BF02954367 ↗
7. 10.1023/A:100448781470910.1023/A:1004487814709 ↗
8. 10.1023/A:100436291571310.1023/A:1004362915713 ↗
9. 10.1080/0360255820806770910.1080/03602558208067709 ↗
10. Malloy RA. · 1994
11. 10.1007/s00397005011710.1007/s003970050117 ↗
12. 10.1177/073168441877052810.1177/0731684418770528 ↗
13. 10.1016/j.mspro.2014.06.33010.1016/j.mspro.2014.06.330 ↗
14. Onken J · Int Polym Sci Tech · 2018 · 43 · 1
15. 10.1002/pen.1166310.1002/pen.11663 ↗
16. 10.4028/www.scientific.net/MSF.589.26310.4028/www.scientific.net/MSF.589.263 ↗
17. 10.1016/S0924-0136(03)00567-310.1016/S0924-0136(03)00567-3 ↗
18. Ross PJ. · 1996
19. Pareek R · Int J Sci Eng Res · 2013 · 4
20. Shayfull Z · Int J Eng Technol · 2011 · 11
21. Kumar Lal S · Int J Eng Res Dev · 2013 · 7 · 35
22. Ozcelik B. · Int Commun Heat Mass Transfer · 2011 · 38 · 1067
23. O’Brien-Saucy AK · J Inj Mold Technol · 2000 · 4 · 152
24. 10.1002/app.2048810.1002/app.20488 ↗
25. 10.1002/pen.2036910.1002/pen.20369 ↗
26. 10.1002/masy.1988020015110.1002/masy.19880200151 ↗
27. 10.1016/B978-0-444-87286-9.50010-310.1016/B978-0-444-87286-9.50010-3 ↗
28. Zhu XK, McGaughy T. A review of fracture toughness testing and evaluation using SENT specimens. In: Proceedings of the 10th international pipeline conference IPC2014 , Calgary, Canada, 29 September–3 October 2014, paper no. 33718.10.1115/IPC2014-33718 ↗
29. 10.1023/A:100891373127810.1023/A:1008913731278 ↗
30. 10.1002/pc.2271010.1002/pc.22710 ↗
31. 10.1122/1.142331210.1122/1.1423312 ↗
32. 10.1007/BF0110570410.1007/BF01105704 ↗
33. 10.1016/0095-8522(65)90022-X10.1016/0095-8522(65)90022-X ↗
34. Hyer MW. · 2009
35. 10.1002/pc.75014050310.1002/pc.750140503 ↗
36. 10.1016/0266-3538(86)90009-610.1016/0266-3538(86)90009-6 ↗
37. 10.1002/pc.75013041010.1002/pc.750130410 ↗
38. Shokri P, Bhatnagar N. Effect of packing pressure and mold temperature on fiber orientation in injection molding reinforced plastics. In: The 8th international conference on flow processes in composite materials (FPCM8) , Douai, France, 11–13 July 2006.
39. 10.1002/pc.75003020710.1002/pc.750030207 ↗