Effects of defects in automated fiber placement laminates and its correlation to automated optical inspection results
Source abstract
Abstract
Automated Fiber Placement (AFP) is a widely used production process for the manufacturing of large scale CFRP parts. However, the occurrence of manufacturing defects such as gaps or overlaps is still a common problem in today’s AFP production environments. This study investigates the effect of different defect configurations on the mechanical performance (i.e., tensile strength, flexural strength, and shear strength) of AFP laminates. The results are then linked to the data generated “inline” by a ply inspection system. We use the Pearson correlation in order to relate the measured defect volume to the strength of samples containing different types of defects. A clear knockdown in tensile strength was found for specimens with gaps or overlaps that caused a high amount of fiber undulations in the laminate. The sensor data analysis showed a similar trend. Specimens with a high defect volume had significantly lower values for the tensile strength. A correlation coefficient of −0.98 between these two values was calculated. The obtained results are a promising step towards automated quality inspection for the AFP process.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Industrial Vision Systems and Defect Detection · Optical measurement and interference techniques · Surface Roughness and Optical Measurements
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
School of Engineering & Design, Department of Aerospace and Geodesy, Chair of Carbon Composites, Technical University of Munich, Germany
Fraunhofer Institute for Casting, Composite and Processing Technology IGCV, Augsburg, Germany
Funding
Bundesministerium für Wirtschaft und Energie · Bayerische Staatsministerium für Wirtschaft, Landesentwicklung und Energie
References (28)
Show source-provided references
1. 10.1016/j.compositesb.2011.12.00310.1016/j.compositesb.2011.12.003 ↗
2. 10.4271/2017-01-215010.4271/2017-01-2150 ↗
3. 10.1177/002199831665539310.1177/0021998316655393 ↗
4. Harik R, Saidy C, Williams SJ, et al. Automated fiber placement defect identity cards: cause, anticipation, existence, significance and progression. In: SAMPE Conference and Exhibition. Long Beach, CA. May 21-24, 2018.
5. 10.4271/2015-01-260810.4271/2015-01-2608 ↗
6. 10.4271/2014-01-227210.4271/2014-01-2272 ↗
7. 10.1007/s10845-021-01774-310.1007/s10845-021-01774-3 ↗
8. Automation Edixia · 2020
9. Gardiner G · 2020
10. Loop Technology Limited · 2020
11. 10.1016/j.compositesb.2016.04.07610.1016/j.compositesb.2016.04.076 ↗
12. 10.1016/j.procir.2016.06.05810.1016/j.procir.2016.06.058 ↗
13. 10.2514/6.1998-178610.2514/6.1998-1786 ↗
14. 10.1016/j.compositesa.2011.01.00710.1016/j.compositesa.2011.01.007 ↗
15. 10.1016/j.compositesa.2015.12.00710.1016/j.compositesa.2015.12.007 ↗
16. 10.1016/j.compositesa.2018.09.01410.1016/j.compositesa.2018.09.014 ↗
17. 10.1016/j.compstruct.2018.06.07810.1016/j.compstruct.2018.06.078 ↗
18. Zenker T · Adv Manuf: Polym Compos Sci · 2019 · 5 · 184
19. 10.1016/j.compstruct.2012.10.03110.1016/j.compstruct.2012.10.031 ↗
20. 10.1515/secm-2013-032210.1515/secm-2013-0322 ↗
21. 10.1007/s12289-020-01581-w10.1007/s12289-020-01581-w ↗
22. Mierzwa A · J Plast Technol · 2018 · 14 · 146
23. 10.1098/rsta.2011.044110.1098/rsta.2011.0441 ↗
24. Brieskorn L · 2020
25. Corporation Hexcel. Data sheet HexPly 8552, https://www.hexcel.com/user_area/content_media/raw/HexPly_8552_eu_DataSheet.pdf (2020, accessed 20 November 2020).
26. 10.1109/TSMC.1979.431007610.1109/TSMC.1979.4310076 ↗
27. 10.1016/j.compstruct.2007.06.00210.1016/j.compstruct.2007.06.002 ↗
28. 10.1109/ANTS47819.2019.911815710.1109/ANTS47819.2019.9118157 ↗