journal article·2016-06

Resistance welding of glass fiber reinforced PET: Effect of weld pressure and heating element geometry

Kyle C Warren, Roberto A Lopez-Anido, Adam L Freund, Habib J Dagher

Publisher page

Abstract

The objective of this paper is to present an investigation of resistance welded thermoplastic joints using stainless steel wire mesh and polyethylene terephthalate (PET) with unidirectional E-glass fiber reinforcement. Five weld pressures and six heating element types were investigated to achieve high quality welds. Scanning electron microscope (SEM) images of welded heating element cross-sections were analyzed to provide a phenomenological description of the weld. Welded joints were also subjected to experimental lap shear evaluation and joint strengths were compared with values from the literature to assess the overall quality of welded joints. Characteristic B-basis strengths and corresponding SEM images are compared to lead to a recommended weld pressure of 345 kPa with a stainless steel wire mesh with 100 openings per inch.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Mechanical Behavior of Composites · Structural Load-Bearing Analysis · Structural Behavior of Reinforced Concrete

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Advanced Structures and Composites Center, University of Maine, USA

References (27)

Show source-provided references
1. Arias M and Ziegmann G. The impulse resistance welding: a new technique for joining advanced thermoplastic composite parts. In: 41st international SAMPE symposium and exhibition , vol. 41, pp.1361–1371.
2. 10.1016/S1359-835X(98)00022-010.1016/S1359-835X(98)00022-0 ↗
3. 10.1177/089270571142865710.1177/0892705711428657 ↗
4. 10.1177/089270571245603110.1177/0892705712456031 ↗
5. 10.1016/S1359-835X(04)00182-410.1016/S1359-835X(04)00182-4 ↗
6. Warren K. Resistance welding of thermoplastic composites for industrial scale wind turbine blades . Master's Thesis, University of Maine, USA, 2012.
7. Hangs B, Burkhart A, Erdman D, et al. Crashworthiness of GF/PET and GF/PA6 tubes produced in a novel rapid tape placement process. In: Society of Plastics Engineers (SPE), Composites Division: 10th Annual Automotive Composites Conference and Exhibition , Troy, Michigan, 15–16 September 2010, pp.711–750. Red Hook, NY: Curran.
8. Grauer D · SAMPE J · 2012 · 48 · 7
9. 10.1016/S0266-3538(00)00025-710.1016/S0266-3538(00)00025-7 ↗
10. Young H · 2004
11. 10.1002/(SICI)1098-2329(199711)16:4<279::AID-ADV3>3.0.CO;2-S10.1002/(SICI)1098-2329(199711)16:4<279::AID-ADV3>3.0.CO;2-S ↗
12. 10.1002/pen.76029231410.1002/pen.760292314 ↗
13. 10.1016/j.compscitech.2007.09.00810.1016/j.compscitech.2007.09.008 ↗
14. Yousefpour A, Simard M, Octeau M, et al. Process optimization of resistance-welded thermoplastic composites using metal mesh heating elements. In: SAMPE 2005 , Long Beach, CA, 2005.
15. Yousefpour A, Hojjati M, Talbot É, et al. Manufacturing process modeling of resistance welding, In: 5th Canadian International Composites Conference , 2005.
16. Chazerain A, Hubert P, Yousefpour A, et al. Mechanical performance of resistance-welded thermoplastic composite double lap shear specimens. In: SAMPE 2009 , vol. 14, Baltimore, MD, 2009.
17. Dubé M. Static and fatigue behavior of thermoplastic composite laminates joined by resistance welding . PhD Thesis, McGill University, USA, 2007.
18. ASTM International. ASTM D5868 Standard Test Method for Lap Shear Adhesion for Fiber Reinforced Plastic (FRP) , ISBN = D5868, 2008.
19. Stavrov D, Bersee H and Beukers A. The influence of the heating element on resistance welding of thermoplastic composite materials. In: ICCM-14 , San Diego, CA, 2003.
20. 10.1177/002199831141298610.1177/0021998311412986 ↗
21. 10.1016/0956-7143(91)90144-610.1016/0956-7143(91)90144-6 ↗
22. 10.1023/A:100887940226710.1023/A:1008879402267 ↗
23. 10.1016/S1359-835X(98)00023-210.1016/S1359-835X(98)00023-2 ↗
24. 10.1016/S0263-8223(00)00047-710.1016/S0263-8223(00)00047-7 ↗
25. Moser L, Villegas IF, Mitschang P, et al. Comparison of three welding processes for joining advanced thermoplastic composites. In: SAMPE , Seattle, WA, 2010, pp. 1–12.
26. 10.1177/073168440707002610.1177/0731684407070026 ↗
27. 10.1016/j.compositesa.2007.07.01410.1016/j.compositesa.2007.07.014 ↗