Thermal characteristics of unidirectional carbon fiber reinforced polymer laminates during orthogonal cutting
Source abstract
Abstract
Carbon fiber reinforced polymer has been used as a major material for primary load-bearing structural components in aviation industry. But its poor heat resistance is an important factor affecting the machining performance, because high cutting temperature above glass transition temperature of resin matrix (normally 300°C or below) may lead to the degradation of the resin matrix. In this study, orthogonal machining experiments were conducted to investigate the effects of cutting parameters, cutting tool geometric parameters, and material parameters on cutting temperature, and the prediction model of cutting temperature about fiber orientation angle ( θ) was built. Cutting temperature was measured by semiartificial thermocouple method. The experimental results revealed that the influence of cutting parameters on cutting temperature was not affected by fiber orientation angle of carbon fiber reinforced polymer. Cutting tool geometric parameters have little effect on cutting temperature. Unlike metal materials, cutting temperature was greatly influenced by θ. Cutting temperature for θ < 90° was significantly higher than that for θ > 90°. The maximum temperature occurred at θ = 90°. The influence of fiber orientation angle was shown in two aspects: changing the springback of unidirectional-carbon fiber reinforced polymer laminates in cutting process, changing material removal mechanism, which affected cutting temperature eventually.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Advanced machining processes and optimization · Mechanical Behavior of Composites · Manufacturing Process and Optimization
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
School of Mechanical Engineering, State Key Laboratory of Mechanical System and Vibration, Shanghai Jiao Tong University, Shanghai, PR China
Shanghai Aerospace Control Technology Institute, Shanghai, PR China
Shanghai Aircraft Manufacturing Factory, Commercial Aircraft Corporation of China, Shanghai, PR China
Funding
National Natural Science Foundation of China · National Engineering and Research Center for Commercial Aircraft Manufacturing · Important National Science & Technology Specific Projects
References (23)
Show source-provided references
1. 10.1016/j.compositesb.2016.11.03310.1016/j.compositesb.2016.11.033 ↗
2. 10.1016/j.compositesb.2017.02.01310.1016/j.compositesb.2017.02.013 ↗
3. 10.1177/073168441561293110.1177/0731684415612931 ↗
4. 10.1016/j.compstruct.2015.08.00710.1016/j.compstruct.2015.08.007 ↗
5. 10.1177/073168441770935910.1177/0731684417709359 ↗
6. 10.1016/j.ijmachtools.2012.01.00110.1016/j.ijmachtools.2012.01.001 ↗
7. 10.1016/j.compositesb.2016.10.01510.1016/j.compositesb.2016.10.015 ↗
8. 10.1177/073168441668496610.1177/0731684416684966 ↗
9. 10.1177/073168441557768810.1177/0731684415577688 ↗
10. 10.1016/j.compstruct.2015.05.03510.1016/j.compstruct.2015.05.035 ↗
11. 10.1016/j.compstruct.2015.11.04310.1016/j.compstruct.2015.11.043 ↗
12. 10.1016/j.cirp.2016.04.00110.1016/j.cirp.2016.04.001 ↗
13. 10.1007/s12541-015-0222-y10.1007/s12541-015-0222-y ↗
14. 10.1016/j.compositesa.2015.11.03610.1016/j.compositesa.2015.11.036 ↗
15. 10.1016/j.ijmachtools.2015.06.00510.1016/j.ijmachtools.2015.06.005 ↗
16. 10.1016/j.compstruct.2014.06.03410.1016/j.compstruct.2014.06.034 ↗
17. 10.1016/j.ijmachtools.2014.06.00810.1016/j.ijmachtools.2014.06.008 ↗
18. 10.1177/073168441351595610.1177/0731684413515956 ↗
19. 10.1016/S0924-0136(00)00549-510.1016/S0924-0136(00)00549-5 ↗
20. 10.1016/j.cirp.2011.03.07710.1016/j.cirp.2011.03.077 ↗
21. Bao YJ. The formation mechanism of disfigurements during drilling and the high-efficiency techniques of drilling C/E composite . PhD Thesis, Dalian University of Technology, China, 2010 (in Chinese).
22. Shaw MC. · 2005
23. Wang YX. · 2001