journal article·2017-10

Carbon fiber-reinforced polymer composite drilling via aluminum chromium nitride-coated tools: Hole quality and tool wear assessment

Muhammad Harris, Muhammad Asif Mahmood Qureshi, Muhammad Qaiser Saleem, Sarmad Ali Khan, Muhammad Mahmood Aslam Bhutta

Publisher page

Abstract

Drilling into carbon fiber-reinforced polymer composites presents a stiff challenge in terms of ensuring hole quality aspects such as delamination, roughness, roundness, etc. while maintaining an adequate tool life. The hardened carbon fibers in laid up form generally give rise to chips in powdered form that contribute significantly to tool wear problem. To overcome the aforementioned issues, the use of high performance tools has been reported. This paper reports on the usage of yet another novel high performing but much economical aluminum chromium nitride-coated tools that are typically employed for metallic parts. The effect of aluminum chromium nitride tools at three spindle speeds with constant feed rate was evaluated on hole quality, tool wear, and chip formation pattern of carbon fiber-reinforced polymer composite plates. The results were compared with the performance of conventional high speed steel tools taken as baseline. It was found that the coated tools help significantly improve hole quality and provide appreciable tool life at specific machining parameters.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Advanced machining processes and optimization · Advanced Machining and Optimization Techniques · Advanced Surface Polishing Techniques

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Department of Industrial & Manufacturing Engineering, Rachna College of Engineering & Technology, Gujranwala, Pakistan

Department of Mechanical Engineering, University Engineering & Technology, Lahore, Pakistan

Department of Industrial and Manufacturing Engineering, University Engineering & Technology, Lahore, Pakistan

References (35)

Show source-provided references
1. 10.1016/S0263-8223(02)00257-X10.1016/S0263-8223(02)00257-X ↗
2. 10.1016/j.compositesb.2012.01.00710.1016/j.compositesb.2012.01.007 ↗
3. 10.1201/978142004198910.1201/9781420041989 ↗
4. 10.1016/j.matdes.2008.03.01410.1016/j.matdes.2008.03.014 ↗
5. 10.1016/j.ijmachtools.2009.08.00210.1016/j.ijmachtools.2009.08.002 ↗
6. Li MJ, Soo SL, Aspinwall DK, et al. Influence of lay-up configuration and feed rate on surface integrity when drilling carbon fiber reinforced plastic (CFRP) composites. In: 2nd CIRP conference on surface integrity (CSI) , Nottingham, UK, 2014, paper no. 13 pp.399–404. Procedia CIRP.10.1016/j.procir.2014.04.068 ↗
7. 10.1016/j.compositesa.2007.08.01010.1016/j.compositesa.2007.08.010 ↗
8. Kalpakjian S · 2001
9. 10.1016/S0890-6955(96)00095-810.1016/S0890-6955(96)00095-8 ↗
10. 10.1016/j.ijmachtools.2005.10.00410.1016/j.ijmachtools.2005.10.004 ↗
11. 10.1016/j.jmatprotec.2005.06.03910.1016/j.jmatprotec.2005.06.039 ↗
12. 10.1007/s00170-014-5616-y10.1007/s00170-014-5616-y ↗
13. 10.1007/s00170-014-6199-310.1007/s00170-014-6199-3 ↗
14. 10.1016/j.jmatprotec.2015.03.04010.1016/j.jmatprotec.2015.03.040 ↗
15. 10.1007/s00170-016-8967-810.1007/s00170-016-8967-8 ↗
16. Oerlikon Balzers. Available at: https://www.oerlikon.com/balzers/com/en/portfolio/balzers-surface-solutions/pvd-and-pacvd-based-coatings/balinit/alcrn-based/balinit-alcrona-pro/ (accessed 18 March 2017).
17. 10.1016/j.jmatprotec.2010.02.01110.1016/j.jmatprotec.2010.02.011 ↗
18. Heisel U and Pfeifroth T. Influence of point angle on drill hole quality and machining forces when drilling CFRP. In: 5th CIRP conference on high performance cutting , Zurich, Switzerland, 2012, paper no. 1, pp.471–476. Procedia CIRP.10.1016/j.procir.2012.04.084 ↗
19. Madhavan S · Int J Eng Res Dev · 2012 · 3 · 36
20. Ramirez C., Poulachon G., Rossi F, et al. Tool wear monitoring and hole surface quality during CFRP drilling. In: 2nd CIRP conference on surface integrity (CSI) , Nottingham, UK, 2014, paper no. 13, pp.163–168. Procedia CIRP 13.10.1016/j.procir.2014.04.028 ↗
21. 10.1115/1.403105210.1115/1.4031052 ↗
22. 10.1115/1.402500810.1115/1.4025008 ↗
23. 10.1115/1.275282710.1115/1.2752827 ↗
24. 10.1115/1.150585410.1115/1.1505854 ↗
25. 10.1080/10426914.2015.100471310.1080/10426914.2015.1004713 ↗
26. Poulachon G, Outeiro J, Ramirez C, et al. Hole surface topography and tool wear in CFRP drilling. In: 3rd CIRP conference on surface integrity (CSI) , Charlotte, NC, 2016, paper no. 9, pp.35–38. Procedia CIRP.10.1016/j.procir.2016.02.348 ↗
27. 10.1007/s12541-013-0252-210.1007/s12541-013-0252-2 ↗
28. Kianfar P, Karimi NZ and Minak G. The effect of chisel edge on drilling-induced delamination. In: 18th international conference on composite materials , London, UK, 2016, pp.18–19.10.14311/APP.2016.3.0019 ↗
29. Astakhov VP and Davim JP. Tools (geometry and material) and tool wear. In: Machining fundamentals and recent advances . London: Springer-Verlag, 2008, pp.29–57.10.1007/978-1-84800-213-5_2 ↗
30. 10.1007/s00170-013-5592-710.1007/s00170-013-5592-7 ↗
31. 10.1007/s40436-015-0129-y10.1007/s40436-015-0129-y ↗
32. 10.1007/s00170-015-7284-y10.1007/s00170-015-7284-y ↗
33. 10.1016/j.wear.2009.01.03110.1016/j.wear.2009.01.031 ↗
34. 10.1016/j.wear.2011.05.03810.1016/j.wear.2011.05.038 ↗
35. Harris M. Evaluation of hole quality and tool wear of CFRP composites using different tool bits . MSc Thesis, University of Engineering & Technology, Lahore, Pakistan, 2016.